Quadra-Fire CB1200I, CB1200MI-MBK owner manual Before removing the side frame. Use a pow

Page 38

CB1200-I Pellet Insert

 

R

E. Glass Replacement

 

 

 

WARNING

 

Door Latch

 

Top & Bottom Frame

 

 

• Glass is 5mm thick high temperature heat-

 

 

 

 

 

resistant ceramic glass.

 

 

 

• DO NOT REPLACE with any other material.

 

 

 

• Alternate material may shatter and cause

Center Posts

 

 

injury

 

 

 

• Remove door from appliance and place face down

Glass

Side

 

Frame

 

on a protected surface to avoid scratching the door.

 

 

 

• Remove all door rope.

 

 

1.

Replacing Center Glass

 

 

NOTE: DO NOT LET Air Wash Spacers fall down from

 

 

 

top frame when removing and replacing center

 

 

 

glass.

Figure 38.1

 

 

 

 

a.Be sure the appliance is allowed to cool, has been unplugged and the exhaust blower is off.

b. Using a nut driver remove the (5) bottom nuts and

Remove Door Latch First

and then Side Frame

remove the bottom glass frame. Figure 38.2.

 

c. Slightly bend up and out of the way the 2 center posts

 

and slide the glass out the bottom.

Door Frame

d. Slide new glass in, reposition the 2 center posts and

shown with no

re-install bottom glass frame.

Glass or Glass

e. Re-rope the door.

Frames

2. Replacing Side Glass

 

NOTE: When removing the side glass with the door

 

latch, you must remove the door latch first

Remove 5 nuts from Bottom Frame

before removing the side frame. Use a pow-

 

ered Phillips head screw driver to remove the

 

4 screws.

 

Figure 38.2

a. Be sure the appliance is allowed to cool, has been

 

unplugged and the exhaust blower is off.

 

b.Remove side glass frame.

c.Loosen the top and bottom frame and slightly bend up and out of the way.

d.Slide glass out the side and slide new glass in.

e.Re-install the side glass frame and tighten the top and bottom frames.

f.Re-install the door latch, if applicable, and re-rope the door.

WARNING

Handle glass with care.

•Inspect the gasket to ensure it is undamaged.

•Do NOT strike, slam or scratch glass.

•Do NOT operate appliance with glass assembly removed.

•Do NOT operate with glass cracked, broken or scratched.

Page 38

7014-188B

February 3, 2010

Page 37 Page 39
Image 38
Page 37 Page 39
Contents CB1200MI-MBK Hot glass will cause burnsCB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Mobile Home ApprovedDesign, Installation & Location Consider- ations Appliance LocationThermostat Location CB1200-I Pellet Insert Locating Your Appliance & ChimneyNegative Pressure DraftInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Fire SafetyTools And Supplies Needed 3Dimensions and Clearances Appliance DimensionsInch 0mm Clearance to Exposed Section and Face Trim Rear Shroud Kit is Required for Built-In InstallationShown with Rear Vent and Optional Outside Air Floor Protection Zero Clearance InstallationsNon-Zero Clearance Installations Inches MillimetersConverting k to R Thermal Conductivity k valueThermal Resistance R value Converting R to kAltering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT ChimneysVenting Termination Requirements Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Venting Systems Full Reline With Outside Air HorizontalCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-UpFor Top Vent Installation Rear Vent Installation PreparationInstalling Rear Shroud Attaching Shroud to Hopper BodyTo adjust hopper Adjustable Hopper OptionsGrille Installation CB1200-I Pellet Insert Outside Air Kit InstructionsAdjustable Hearth Support Size 9D x 45W, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCB1200-I Pellet Insert Optional Brick Set Installation Brick Clip InstallationRight Thermostat InstallationTop Log, Left Front LogWood Pellets Shelled Field Corn Cont’d 8Operating InstructionsFuel Size, Material and Storage Shelled Field CornStarting Your First Fire CB1200-I Pellet Insert General Operating InformationBefore Your First Fire Thermostat Calls For HeatIgnition Cycles CB1200-I Pellet Insert Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Frequently Asked Questions Issues SolutionsTroubleshooting SymptomTroubleshooting Cont’d Symptom Possible Cause Corrective ActionTroubleshooting Cont’d Maintaining & Servicing Your Appliance 10Proper Shutdown ProcedureQuick Reference Maintenance Chart Types of FuelCleaning the Hopper Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Pan See Disposal of Ashes Frequency As neededCleaning Exhaust Path Cleaning Heat Exchanger Chambers & Drop TubeCleaning Beneath Heat Exchanger Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning Exhaust Blower Requires No LubricationDoor Gasket Inspection CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is RequiredBefore removing the side frame. Use a pow Ered Phillips head screw driver to remove ScrewsIgniter Replacement Baffle Removal Component Function Reference MaterialsCB 200-I Pellet Insert Thermostat Vacuum SwitchWiring Harness See .1 below Snap Disc #1 Convection Blower 125FCB1200-I Pellet Insert Component Locations Control BoxCB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number DR-CB12-NL-BStocked Description Comments Part NumberCB1200-I Pellet Insert Fasteners Stocked at DepotCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information
Top Page Image Contents