Quadra-Fire CB1200MI-MBK, CB1200I owner manual Hot glass will cause burns

Page 1

CB1200-I PELLET INSERT

Owner’s Manual

Installation and Operation

Model:

CB1200MI-MBK

R

Tested and	O-T L	Portland
Listed by	O-T L	Oregon USA

C US

OMNI-Test Laboratories, Inc.

NOTICE

DO NOT DISCARD THIS MANUAL

• Important operating and	• Read, understand and	• Leave this manual with
maintenance instruc-	follow these instruc-	party responsible for use
tions included.	tions for safe installa-	and operation.
	tion and operation.

DO DISCARDNOT

WARNING

Please read this entire manual before installation and use of this pellet fuel-burning room heater. Failure to follow these instructions could result in property damage, bodily injury or even death.

•Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance.

•Do not overfire - If any external part starts to glow, you are overfiring. Reduce feed rate. Overfiring will void your warranty.

•Comply with all minimum clearances to com- bustibles as specified. Failure to comply may cause house fire.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

•Do not touch glass until it is cooled

•NEVER allow children to touch glass

•Keep children away

•CAREFULLY SUPERVISE children in same room as fireplace.

•Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

•Keep clothing, furniture, draperies and other flammable materials away.

CAUTION

Tested and approved for wood pellets and shelled field corn fuel only. Burning of any other type of fuel voids your warranty.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult local building, fire officials or authorities having jurisdic- tion about restrictions, installation inspection, and permits.

www.quadrafire.com

7014-188B

February 3, 2010

Image 1

Contents Hot glass will cause burns CB1200MI-MBKWelcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Glass Specifications Appliance Certification BTU & Efficiency SpecificationsListing and Code Approvals Mobile Home ApprovedAppliance Location Design, Installation & Location Consider- ationsNegative Pressure CB1200-I Pellet Insert Locating Your Appliance & ChimneyThermostat Location DraftTools And Supplies Needed CB1200-I Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesShown with Rear Vent and Optional Outside Air Rear Shroud Kit is Required for Built-In InstallationInch 0mm Clearance to Exposed Section and Face Trim Non-Zero Clearance Installations Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kS629M, Standard for 650oC FACTORY-BUILT Chimneys Altering the Factory-Built FireplaceChimney and Exhaust Connection Vent InformationVenting Termination Requirements CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Full Reline With Outside Air Horizontal Venting SystemsCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home 7Appliance Set-Up Rear Shroud InstallationInstalling Rear Shroud Rear Vent Installation PreparationFor Top Vent Installation Attaching Shroud to Hopper BodyGrille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsSize 9D x 45W, 2 to 10 Height Adjustment Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dBrick Clip Installation CB1200-I Pellet Insert Optional Brick Set InstallationTop Log, Left Thermostat InstallationRight Front LogFuel Size, Material and Storage 8Operating InstructionsWood Pellets Shelled Field Corn Cont’d Shelled Field CornBefore Your First Fire CB1200-I Pellet Insert General Operating InformationStarting Your First Fire Thermostat Calls For HeatFeed Rate Adjustment Instructions CB1200-I Pellet Insert Fire CharacteristicsIgnition Cycles Issues Solutions CB1200-I Pellet Insert Frequently Asked QuestionsSymptom TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Cont’dTroubleshooting Cont’d Quick Reference Maintenance Chart 10Proper Shutdown ProcedureMaintaining & Servicing Your Appliance Types of FuelCleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger Chambers & Drop TubeCleaning Exhaust Path Cleaning the GlassDoor Gasket Inspection Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly Immediate Attention and Cleaning is Required CB1200-I Pellet Insert High Ash Fuel Content MaintenanceEred Phillips head screw driver to remove Screws Before removing the side frame. Use a powIgniter Replacement Baffle Removal CB 200-I Pellet Insert Reference MaterialsComponent Function Wiring Harness See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 125FControl Box CB1200-I Pellet Insert Component LocationsCB1200-I Pellet Insert Exploded Drawing Important this is Dated Information HOW to Order CB1200-I Pellet Insert Service Parts and AccessoriesDR-CB12-NL-B Stocked At Depot Description Comments Part NumberDescription Comments Part Number StockedCB1200-I Pellet Insert Stocked at Depot FastenersDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information