Quadra-Fire CB1200MI-MBK Design, Installation & Location Consider- ations, Appliance Location

Page 5

R

CB1200-I Pellet Insert

2

Getting Started

 

A.Design, Installation & Location Consider- ations

Since pellet exhaust can contain ash, soot or sparks, you must consider the location of:

• Windows

1.Appliance Location

Notice: Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

•Air Intakes

•Air Conditioner

•Overhang, soffits, porch roofs, adjacent walls

•Landscaping, vegetation

When locating vent and venting termination, vent above roof line when possible.

It is a good idea to plan your installation on paper, using exact measurements for clearances and floor protection, before actually beginning the installation

Consideration must be given to:

•Safety, convenience, traffic flow

•Placement of the chimney and chimney connector.

Warning! Risk of Fire Damaged parts could impair safe operation. Do NOT install damaged, incomplete or substitute components.

CAUTION! If burning shelled field corn, you must use ap- proved venting specifically designed for corn to prevent corro- sion or degradation. Follow the instructions from the venting manufacturer.

• If you are not using an existing chimney, place the appli-

Notice: Locating the appliance in a location of

 

ance where there will be a clear passage for a factory-

 

built listed chimney through the ceiling and roof.

 

considerable air movement can cause intermittent smoke

• Installing an optional outside air kit would affect the loca-

spillage from appliance. Do not locate appliance near:

• Frequently open doors

 

tion of the vent termination.

 

 

 

 

• Central heat outlets or returns

 

 

 

 

 

Recommended Location:

 

Recommended Location:

• Above peak

 

 

• Above peak

• Inside heated space

Location NOT recommended:

•Not the highest point of the roof

•Wind loading possible

Windward

Marginal Location:

• Below peak

Recommended:

•Insulated exterior chase in cooler climates

Marginal Location:

• Wind loading possible

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Leeward

Recommended: Outside Air Intake on windward side

Multi-level Roofs

NOT recommended: Outside Air Intake on leeward side

Figure 5.1

February 3, 2010

7014-188B

Page

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Hot glass will cause burns CB1200MI-MBKWelcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Glass Specifications Appliance Certification BTU & Efficiency SpecificationsListing and Code Approvals Mobile Home ApprovedAppliance Location Design, Installation & Location Consider- ationsNegative Pressure CB1200-I Pellet Insert Locating Your Appliance & ChimneyThermostat Location DraftInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Fire SafetyTools And Supplies Needed Appliance Dimensions 3Dimensions and ClearancesInch 0mm Clearance to Exposed Section and Face Trim Rear Shroud Kit is Required for Built-In InstallationShown with Rear Vent and Optional Outside Air Non-Zero Clearance Installations Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kS629M, Standard for 650oC FACTORY-BUILT Chimneys Altering the Factory-Built FireplaceVenting Termination Requirements Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Full Reline With Outside Air Horizontal Venting SystemsCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home 7Appliance Set-Up Rear Shroud InstallationInstalling Rear Shroud Rear Vent Installation PreparationFor Top Vent Installation Attaching Shroud to Hopper BodyGrille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsSize 9D x 45W, 2 to 10 Height Adjustment Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dBrick Clip Installation CB1200-I Pellet Insert Optional Brick Set InstallationTop Log, Left Thermostat InstallationRight Front LogFuel Size, Material and Storage 8Operating InstructionsWood Pellets Shelled Field Corn Cont’d Shelled Field CornBefore Your First Fire CB1200-I Pellet Insert General Operating InformationStarting Your First Fire Thermostat Calls For HeatIgnition Cycles CB1200-I Pellet Insert Fire CharacteristicsFeed Rate Adjustment Instructions Issues Solutions CB1200-I Pellet Insert Frequently Asked QuestionsSymptom TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Cont’dTroubleshooting Cont’d Quick Reference Maintenance Chart 10Proper Shutdown ProcedureMaintaining & Servicing Your Appliance Types of FuelCleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger Chambers & Drop TubeCleaning Exhaust Path Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning Exhaust Blower Requires No LubricationDoor Gasket Inspection Immediate Attention and Cleaning is Required CB1200-I Pellet Insert High Ash Fuel Content MaintenanceEred Phillips head screw driver to remove Screws Before removing the side frame. Use a powIgniter Replacement Baffle Removal Component Function Reference MaterialsCB 200-I Pellet Insert Wiring Harness See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 125FControl Box CB1200-I Pellet Insert Component LocationsCB1200-I Pellet Insert Exploded Drawing Important this is Dated Information HOW to Order CB1200-I Pellet Insert Service Parts and AccessoriesDR-CB12-NL-B Stocked At Depot Description Comments Part NumberDescription Comments Part Number StockedCB1200-I Pellet Insert Stocked at Depot FastenersDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information
Top Page Image Contents