Quadra-Fire CB1200I, CB1200MI-MBK CB1200-I Pellet Insert Optional Brick Set Installation

Page 24

CB1200-I Pellet Insert

R

G. Optional Brick Set Installation

1.Slide bottom of left rear brick in first; rotate top edge to- ward rear of appliance and then rotate outer edge toward rear of appliance, until brick slides into place. Figure 24.1. Repeat for right rear brick.

2.Place left side brick along left side of firebox, making sure chamfered (beveled) back edge fits snugly next to left rear brick. Figure 24.2. Repeat with right side brick.

3.Complete brick set, correctly installed. Figure 24.4.

1

Figure 24.1

WARNING

Risk of Injury.

Brick may have small wires protruding from the back of brick.

H.Brick Clip Installation

1.After the brick set has been installed, 2 brick clips need to be installed on the outer edge of baffle to keep the brick set in place. Remove the baffles from the appliance before installing the brick clips.

2.Using pliers, bend the brick clip slightly past 90° in the direction shown in Figure 24.4.

3.Position the brick clip as shown in Figure 24.4 and use pliers to crimp around the outside edge of the baffle. Figure 24.5 shows the finished shape of the brick clip after being bent around the outside edge of the baffle.

4.Slide the baffles back into place making sure that the brick clip holds the brick out toward the wall of the firebox. Push back on the sides so they keep the rear bricks in place. Repeat for the opposite side.

3

1

2

 

 

Figure 24.2

3

4

1

2

Figure 24.3

 

Approximately

 

1 inch

 

Outside edge

 

of Baffle

Top outside

Brick Clip

corner of Baffle

 

Figure 24.4

Installed Clip

Figure 24.5

Page 24

7014-188B

February 3, 2010

Image 24
Contents CB1200MI-MBK Hot glass will cause burnsCB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home ApprovedDesign, Installation & Location Consider- ations Appliance LocationCB1200-I Pellet Insert Locating Your Appliance & Chimney Negative PressureThermostat Location DraftCB1200-I Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsRear Shroud Kit is Required for Built-In Installation Shown with Rear Vent and Optional Outside AirInch 0mm Clearance to Exposed Section and Face Trim Zero Clearance Installations Non-Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Conductivity k value Thermal Resistance R valueConverting k to R Converting R to kAltering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT ChimneysVent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-UpRear Vent Installation Preparation Installing Rear ShroudFor Top Vent Installation Attaching Shroud to Hopper BodyAdjustable Hopper Options Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsAdjustable Hearth Support Size 9D x 45W, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCB1200-I Pellet Insert Optional Brick Set Installation Brick Clip InstallationThermostat Installation Top Log, LeftRight Front Log8Operating Instructions Fuel Size, Material and StorageWood Pellets Shelled Field Corn Cont’d Shelled Field CornCB1200-I Pellet Insert General Operating Information Before Your First FireStarting Your First Fire Thermostat Calls For HeatCB1200-I Pellet Insert Fire Characteristics Feed Rate Adjustment InstructionsIgnition Cycles CB1200-I Pellet Insert Frequently Asked Questions Issues SolutionsTroubleshooting SymptomTroubleshooting Cont’d Symptom Possible Cause Corrective ActionTroubleshooting Cont’d 10Proper Shutdown Procedure Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Types of FuelCleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash PanCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the GlassCleaning Exhaust Blower Requires No Lubrication Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is RequiredBefore removing the side frame. Use a pow Ered Phillips head screw driver to remove ScrewsIgniter Replacement Baffle Removal Reference Materials CB 200-I Pellet InsertComponent Function Vacuum Switch Wiring Harness See .1 belowThermostat Snap Disc #1 Convection Blower 125FCB1200-I Pellet Insert Component Locations Control BoxCB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number DR-CB12-NL-BStocked Description Comments Part NumberCB1200-I Pellet Insert Fasteners Stocked at DepotCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information