Quadra-Fire CB1200MI-MBK Adjustable Hearth Support, Size 9D x 45W, 2 to 10 Height Adjustment

Page 21

R

 

CB1200-I Pellet Insert

E. Adjustable Hearth Support

 

 

Size: 9”D x 45”W, 2” to 10” Height Adjustment

ExPLODED VIEW OF SCISSORS

 

 

Included in Kit: (1) trim top, (1) trim front, (2) trim sides,

 

 

double-sided tape (already installed)

 

SCREWS ARE CIRCLED

Tools Needed: Phillips head screw driver, sheet metal

 

 

shears, measuring tape, gloves

 

 

1. The 10 screws on each set of scissors will already be

DOUBLE-SIDED TAPE

DOUBLE-SIDED TAPE

loose when shipped. Figure 21.1.

Figure 21.1

 

 

 

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips head screw driver. Figure 21.2.

3.Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess mate-

rial from top of trim’s edge, not bottom. This edge will

ExPAND SCISSORS TO DESIRED HEIGH T

 

be sharp; wear gloves to prevent injury to your hands.

 

 

Figure 21.3.

 

 

4. Using sheet metal shears, cut trim along the marked

 

 

edge. The cut edge fits under lip of top trim, so it allows

 

 

for some variance in your straight edge.

 

CUT TOP EDGE OF TRIM,

5. The double-sided tape that holds front and side trims to

INSTALL FRONT TRIM LAST.

NOT BOTTOM EDGE

CORNERS OVERLAP SIDE

 

scissors has a powerful bonding adhesive. Adjustments

TRIM PIECES

 

 

 

are extremely difficult once trim has adhered to tape. Do

Figure 21.2

 

a dry run first without removing paper from tape.

 

 

6.Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece. The front piece overlaps side pieces.

7.Once you are satisfied with the positioning, remove trim

and set aside.

8. Remove the paper from double-sided tape that is to

Decorative tile

accept trim side. Align side and then press hard against

may be installed

tape to secure side piece. Repeat for other side. Install

 

front trim piece last.

 

9. There are 3 holes in the back flange of the top to secure

 

it to the wall if necessary. Use the appropriate fastener

 

for the type of wall material, i.e., brick, sheetrock, etc.

Figure 21.3

NOTE: 3/8 inch (9.5mm) thick tile or like material can be

 

cut to size and fit under lip of top trim edge for a decora-

 

tive touch. Figure 21.3.

 

WARNING

Sheet metal trim edges will be sharp.

For safety purposes wear gloves.

Injury can occur.

February 3, 2010

7014-188B

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Hot glass will cause burns CB1200MI-MBKWelcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Glass Specifications Appliance Certification BTU & Efficiency SpecificationsListing and Code Approvals Mobile Home ApprovedAppliance Location Design, Installation & Location Consider- ationsNegative Pressure CB1200-I Pellet Insert Locating Your Appliance & ChimneyThermostat Location DraftCB1200-I Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesRear Shroud Kit is Required for Built-In Installation Shown with Rear Vent and Optional Outside AirInch 0mm Clearance to Exposed Section and Face Trim Non-Zero Clearance Installations Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kS629M, Standard for 650oC FACTORY-BUILT Chimneys Altering the Factory-Built FireplaceVent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart CB1200-I Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation Full Reline With Outside Air Horizontal Venting SystemsCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home 7Appliance Set-Up Rear Shroud InstallationInstalling Rear Shroud Rear Vent Installation PreparationFor Top Vent Installation Attaching Shroud to Hopper BodyGrille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsSize 9D x 45W, 2 to 10 Height Adjustment Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dBrick Clip Installation CB1200-I Pellet Insert Optional Brick Set InstallationTop Log, Left Thermostat InstallationRight Front LogFuel Size, Material and Storage 8Operating InstructionsWood Pellets Shelled Field Corn Cont’d Shelled Field CornBefore Your First Fire CB1200-I Pellet Insert General Operating InformationStarting Your First Fire Thermostat Calls For HeatCB1200-I Pellet Insert Fire Characteristics Feed Rate Adjustment InstructionsIgnition Cycles Issues Solutions CB1200-I Pellet Insert Frequently Asked QuestionsSymptom TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Cont’dTroubleshooting Cont’d Quick Reference Maintenance Chart 10Proper Shutdown ProcedureMaintaining & Servicing Your Appliance Types of FuelCleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger Chambers & Drop TubeCleaning Exhaust Path Cleaning the GlassCleaning Exhaust Blower Requires No Lubrication Door Gasket InspectionPreparing Firebox for Non-Burn Season Frequency Yearly Immediate Attention and Cleaning is Required CB1200-I Pellet Insert High Ash Fuel Content MaintenanceEred Phillips head screw driver to remove Screws Before removing the side frame. Use a powIgniter Replacement Baffle Removal Reference Materials CB 200-I Pellet InsertComponent Function Wiring Harness See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 125FControl Box CB1200-I Pellet Insert Component LocationsCB1200-I Pellet Insert Exploded Drawing Important this is Dated Information HOW to Order CB1200-I Pellet Insert Service Parts and AccessoriesDR-CB12-NL-B Stocked At Depot Description Comments Part NumberDescription Comments Part Number StockedCB1200-I Pellet Insert Stocked at Depot FastenersDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information
Top Page Image Contents