Quadra-Fire CB1200I Listing and Code Approvals, Mobile Home Approved, Glass Specifications

Page 4

CB1200-I Pellet Insert

Listing and Code Approvals

R

A. Appliance Certification

E. BTU & Efficiency Specifications

MODEL:

1200-I Pellet Insert

LABORATORY:

OMNI Test Laboratories, Inc

REPORT NO.

061-S-13-2

TYPE:

Solid Fuel Room Heater/Pellet Fuel

 

Burning Type Insert

STANDARD:

ASTM E1509-95, ULC S628-93, ULC

 

S610-M87, ULC S628-M93 and ULC/

 

ORD-C1482-M1990 Room Heater Pellet

 

Fuel Burning Type and (UM) 84-HUD,

 

Mobile Home Approved

Emissions Rating:

.9 grams/hr

*BTU Output:

14,000 - 40,000 / hr

Heating Capacity:

up to 2,500 sq. ft. depending

 

on climate zone

Hopper Capacity:

60-75 lbs

Fuel:

Wood Pellets or Shelled Corn

Shipping Weight:

243 lbs

*BTU output will vary, depending on the brand of fuel you use in your appliance. Consult your Quadra-Fire dealer for best results.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM

E1509-95, ULC S628-93, ULC S610-M87, ULC/ORD-C- 1482-M1990, (UM) 84-HUD.

WARNING! Risk of Fire! Hearth & Home Technologies dis- claims any responsibility for, and the warranty and agency listing will be voided by the above actions.

B. Mobile Home Approved

This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home floor, ceiling, and walls must be maintained.

The appliance must be properly grounded to the frame of the mobile home and use only listed pellet vent, Class “L” or “PL” connector pipe. A Quadra-Fire Outside Air Kit must be installed in a mobile home installation.

Note: This appliance is also approved for installation into a shop.

C. Glass Specifications

This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

D. Electrical Rating

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps

NOTE: Some generator or battery back-up systems may not be compatable with the micro-processor elec- tronics on this appliance. Please consult the power supply manufacturer for compatable systems.

DO NOT:

•Install or operate damaged appliance

•Modify appliance

•Install other than as instructed by Hearth & Home Technologies

•Operate the appliance without fully assembling all components

•Overfire

•Install any component not approved by Hearth & Home Technologies

•Install parts or components not Listed or approved. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified installer, service agency or your dealer.

NOTE: Hearth & Home Technologies, manufacturer of this appliance, reserves the right to alter its products, their specifications and/or price without notice.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

Page

7014-188B

February 3, 2010

Page 3 Page 5
Image 4
Page 3 Page 5
Contents CB1200MI-MBK Hot glass will cause burnsCB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home ApprovedDesign, Installation & Location Consider- ations Appliance LocationCB1200-I Pellet Insert Locating Your Appliance & Chimney Negative PressureThermostat Location DraftTools And Supplies Needed CB1200-I Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsShown with Rear Vent and Optional Outside Air Rear Shroud Kit is Required for Built-In InstallationInch 0mm Clearance to Exposed Section and Face Trim Zero Clearance Installations Non-Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Conductivity k value Thermal Resistance R valueConverting k to R Converting R to kAltering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT ChimneysChimney and Exhaust Connection Vent InformationVenting Termination Requirements CB1200-I Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation Venting Systems Full Reline With Outside Air HorizontalCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-UpRear Vent Installation Preparation Installing Rear ShroudFor Top Vent Installation Attaching Shroud to Hopper BodyAdjustable Hopper Options Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsAdjustable Hearth Support Size 9D x 45W, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCB1200-I Pellet Insert Optional Brick Set Installation Brick Clip InstallationThermostat Installation Top Log, LeftRight Front Log8Operating Instructions Fuel Size, Material and StorageWood Pellets Shelled Field Corn Cont’d Shelled Field CornCB1200-I Pellet Insert General Operating Information Before Your First FireStarting Your First Fire Thermostat Calls For HeatFeed Rate Adjustment Instructions CB1200-I Pellet Insert Fire CharacteristicsIgnition Cycles CB1200-I Pellet Insert Frequently Asked Questions Issues SolutionsTroubleshooting SymptomTroubleshooting Cont’d Symptom Possible Cause Corrective ActionTroubleshooting Cont’d 10Proper Shutdown Procedure Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Types of FuelCleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash PanCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the GlassDoor Gasket Inspection Cleaning Exhaust Blower Requires No LubricationPreparing Firebox for Non-Burn Season Frequency Yearly CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is RequiredBefore removing the side frame. Use a pow Ered Phillips head screw driver to remove ScrewsIgniter Replacement Baffle Removal CB 200-I Pellet Insert Reference MaterialsComponent Function Vacuum Switch Wiring Harness See .1 belowThermostat Snap Disc #1 Convection Blower 125FCB1200-I Pellet Insert Component Locations Control BoxCB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number DR-CB12-NL-BStocked Description Comments Part NumberCB1200-I Pellet Insert Fasteners Stocked at DepotCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information
Top Page Image Contents