Quadra-Fire CB1200MI-MBK, CB1200I owner manual Mobile Home

Page 17

	R	CB1200-I Pellet Insert


6	Mobile Home
6

A. Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit for installation in a mobile home.

1.An outside air inlet must be provided for the combustion air and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while the appliance is in use to prevent room air starvation which causes smoke spillage. Smoke spillage can also set off smoke alarms.

2.The combustion air duct system must be made of metal. It must permit zero clearance to combustible construc- tion and prevent material from dropping into the inlet or into the area beneath the dwelling and contain a rodent screen.

3.The appliance must be secured to the mobile home structure by bolting it to the floor (using lag bolts) in two places. Use the same holes that secured the appliance to the shipping pallet.

4.The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC approved grounding device.

5.Refer to Clearances to Combustibles and floor pro- tection requirements on pages 9 & 10 for listings to combustibles and appropriate chimney systems.

6.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the the exterior of the structure.

7.Follow the chimney manufacturer’s instructions when installing the vent system for use in a mobile home.

8.Installation shall be in accordance with the Manufactur- ers Home & Safety Standard (HUD) CFR 3280, Part 24.

WARNING

Installation must comply with Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE MAIN- TAINED

Do NOT cut through:

•Floor joist, wall, studs or ceiling trusses.

•Any supporting material that would affect the structural integrity.

CAUTION

Never draw outside combustion air from:

•Wall, floor or ceiling cavity

•Enclosed space such as an attic or garage

	Spark Arrestor Cap
Storm Collar
	Roof Flashing
Joist Shield/Firestop	Approved Class “L”
	or “PL” Pellet Vent

Figure 17.1

WARNING

Asphyxiation Risk.

NEVER INSTALL IN A SLEEPING ROOM. Consumes oxygen in the room.

February 3, 2010

7014-188B

Page 17

Image 17

Contents Hot glass will cause burns CB1200MI-MBKWelcome to the Quadra-Fire Family CB1200-I Pellet InsertTable of Contents Glass Specifications Appliance Certification BTU & Efficiency SpecificationsListing and Code Approvals Mobile Home ApprovedAppliance Location Design, Installation & Location Consider- ationsNegative Pressure CB1200-I Pellet Insert Locating Your Appliance & ChimneyThermostat Location DraftInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Fire SafetyTools And Supplies Needed Appliance Dimensions 3Dimensions and ClearancesInch 0mm Clearance to Exposed Section and Face Trim Rear Shroud Kit is Required for Built-In InstallationShown with Rear Vent and Optional Outside Air Non-Zero Clearance Installations Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Resistance R value Thermal Conductivity k valueConverting k to R Converting R to kS629M, Standard for 650oC FACTORY-BUILT Chimneys Altering the Factory-Built FireplaceVenting Termination Requirements Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Full Reline With Outside Air Horizontal Venting SystemsCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home 7Appliance Set-Up Rear Shroud InstallationInstalling Rear Shroud Rear Vent Installation PreparationFor Top Vent Installation Attaching Shroud to Hopper BodyGrille Installation Adjustable Hopper OptionsTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsSize 9D x 45W, 2 to 10 Height Adjustment Adjustable Hearth SupportCB1200-I Pellet Insert Panel and Trim Set Completed View CB1200-I Pellet Insert Panel and Trim Set Cont’dBrick Clip Installation CB1200-I Pellet Insert Optional Brick Set InstallationTop Log, Left Thermostat InstallationRight Front LogFuel Size, Material and Storage 8Operating InstructionsWood Pellets Shelled Field Corn Cont’d Shelled Field CornBefore Your First Fire CB1200-I Pellet Insert General Operating InformationStarting Your First Fire Thermostat Calls For HeatIgnition Cycles CB1200-I Pellet Insert Fire CharacteristicsFeed Rate Adjustment Instructions Issues Solutions CB1200-I Pellet Insert Frequently Asked QuestionsSymptom TroubleshootingSymptom Possible Cause Corrective Action Troubleshooting Cont’dTroubleshooting Cont’d Quick Reference Maintenance Chart 10Proper Shutdown ProcedureMaintaining & Servicing Your Appliance Types of FuelCleaning Ash Pan Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Cleaning Heat Exchanger Chambers & Drop TubeCleaning Exhaust Path Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning Exhaust Blower Requires No LubricationDoor Gasket Inspection Immediate Attention and Cleaning is Required CB1200-I Pellet Insert High Ash Fuel Content MaintenanceEred Phillips head screw driver to remove Screws Before removing the side frame. Use a powIgniter Replacement Baffle Removal Component Function Reference MaterialsCB 200-I Pellet Insert Wiring Harness See .1 below Vacuum SwitchThermostat Snap Disc #1 Convection Blower 125FControl Box CB1200-I Pellet Insert Component LocationsCB1200-I Pellet Insert Exploded Drawing Important this is Dated Information HOW to Order CB1200-I Pellet Insert Service Parts and AccessoriesDR-CB12-NL-B Stocked At Depot Description Comments Part NumberDescription Comments Part Number StockedCB1200-I Pellet Insert Stocked at Depot FastenersDate of Service Performed By Description of Service CB1200-I Pellet Insert Service And Maintenance LogCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information