Quadra-Fire CB1200I, CB1200MI-MBK owner manual 3Dimensions and Clearances, Appliance Dimensions

Page 8

CB1200-I Pellet Insert

3Dimensions and Clearances

A. Appliance Dimensions

R

	40 in. (1016mm)
	29-1/4 in. (743mm)
	22 in. (559mm)
	8-3/4 in.
	(222mm)
10-3/4 in.	13 in. (330mm)
(273mm)
	C
	L
	12 in. (305mm)
	28-1/2 in. (724mm)

Figure 8.1 - Top View

B

A

Figure 8.2 - Front View

				Panel	A	B
				Standard	30 inches (762mm)	40 inches (1016mm)
				Large	33 inches (838mm)	50 inches (1270mm)
					12 in.
				(305mm)
				13 in.
				(330mm)
				10-3/4 in.
				(273mm)
30 in. (762mm)	22 in. (559mm) (Hopper Up)	19-1/2 in. (495mm)	(Hopper Down)		25-1/2 in.
					(648mm)
				11in. (279mm)
					11"
				(279mm)

Figure 8.3 - Side View

Page

7014-188B

February 3, 2010

Image 8

Contents CB1200MI-MBK Hot glass will cause burnsCB1200-I Pellet Insert Welcome to the Quadra-Fire FamilyTable of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home ApprovedDesign, Installation & Location Consider- ations Appliance LocationCB1200-I Pellet Insert Locating Your Appliance & Chimney Negative PressureThermostat Location DraftInspect Appliance & Components and Pre-Use Check List CB1200-I Pellet Insert Fire SafetyTools And Supplies Needed 3Dimensions and Clearances Appliance DimensionsInch 0mm Clearance to Exposed Section and Face Trim Rear Shroud Kit is Required for Built-In InstallationShown with Rear Vent and Optional Outside Air Zero Clearance Installations Non-Zero Clearance InstallationsFloor Protection Inches MillimetersThermal Conductivity k value Thermal Resistance R valueConverting k to R Converting R to kAltering the Factory-Built Fireplace S629M, Standard for 650oC FACTORY-BUILT ChimneysVenting Termination Requirements Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartCB1200-I Pellet Insert Equivalent Feet of Pipe Venting Systems Full Reline With Outside Air HorizontalCB1200-I Pellet Insert Full Reline With Outside Air Vertical Mobile Home Rear Shroud Installation 7Appliance Set-UpRear Vent Installation Preparation Installing Rear ShroudFor Top Vent Installation Attaching Shroud to Hopper BodyAdjustable Hopper Options Grille InstallationTo adjust hopper CB1200-I Pellet Insert Outside Air Kit InstructionsAdjustable Hearth Support Size 9D x 45W, 2 to 10 Height AdjustmentCB1200-I Pellet Insert Panel and Trim Set CB1200-I Pellet Insert Panel and Trim Set Cont’d Completed ViewCB1200-I Pellet Insert Optional Brick Set Installation Brick Clip InstallationThermostat Installation Top Log, LeftRight Front Log8Operating Instructions Fuel Size, Material and StorageWood Pellets Shelled Field Corn Cont’d Shelled Field CornCB1200-I Pellet Insert General Operating Information Before Your First FireStarting Your First Fire Thermostat Calls For HeatIgnition Cycles CB1200-I Pellet Insert Fire CharacteristicsFeed Rate Adjustment Instructions CB1200-I Pellet Insert Frequently Asked Questions Issues SolutionsTroubleshooting SymptomTroubleshooting Cont’d Symptom Possible Cause Corrective ActionTroubleshooting Cont’d 10Proper Shutdown Procedure Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Types of FuelCleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash PanCleaning the Hopper See Disposal of Ashes Frequency As neededCleaning Heat Exchanger Chambers & Drop Tube Cleaning Beneath Heat ExchangerCleaning Exhaust Path Cleaning the GlassPreparing Firebox for Non-Burn Season Frequency Yearly Cleaning Exhaust Blower Requires No LubricationDoor Gasket Inspection CB1200-I Pellet Insert High Ash Fuel Content Maintenance Immediate Attention and Cleaning is RequiredBefore removing the side frame. Use a pow Ered Phillips head screw driver to remove ScrewsIgniter Replacement Baffle Removal Component Function Reference MaterialsCB 200-I Pellet Insert Vacuum Switch Wiring Harness See .1 belowThermostat Snap Disc #1 Convection Blower 125FCB1200-I Pellet Insert Component Locations Control BoxCB1200-I Pellet Insert Exploded Drawing CB1200-I Pellet Insert Service Parts and Accessories Important this is Dated Information HOW to OrderStocked At Depot Description Comments Part Number DR-CB12-NL-BStocked Description Comments Part NumberCB1200-I Pellet Insert Fasteners Stocked at DepotCB1200-I Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceCB1200-I Pellet Insert Warranty Policy CB1200-I Pellet Insert Contact Information