Adjusting the position of a locate point or marker | Yamaha AW2400

Adjusting the position of a locate point or marker

Adjusting the position of a locate point or marker

Here’s how you can adjust the position of a previously-registered locate point or marker. These operations are performed via the EDIT screen Mark Adj. page.

To call this page press the Work Navigate section [EDIT] key as many times as necessary, or press the [F3] key after pressing the [EDIT] key.

A

B

E

C

D

1Locator Position ﬁeld

Shows the various locate points (Quick Locator points not included).

BQuick Locator/Marker ﬁeld

Shows the Quick Locator or Marker points.

CLOCATOR button

DMARKER button

These buttons determine whether the Quick Locator or Marker points appear in the Quick Locator/Marker ﬁeld.

EDELETE button (Marker display only)

Deletes the currently selected marker.

Adjusting the position of a locate point

1 Call the EDIT screen Mark Adj. page by either pressing the Work Navigate section [EDIT] key as many times as necessary, or by pressing the [F3] key after pressing the [EDIT] key.

2 The Locator Position ﬁeld is used to edit the various locate points (not including the Quick Locator points).

The positions for each locator are displayed in the Locator Position ﬁeld.

A B C

1Locate points

Shows the type of locate point and its abbreviation.

BPosition

Shows the position of each locate point in time code or the current counter display format.

CMeasure/beat

Shows the position of each locate point as measures/ beats. This value is calculated based on the tempo and time signature of the tempo map (→ p. 175).

The format in which the position is displayed will depend on the locate point. The following table shows the display format for each locate point.

Locate point	Position	Measure/Beat
REL.ZERO	Time code	--

START	Time code	Measure/beat

END	Time code	Measure/beat

IN	Counter display format	Measure/beat

OUT	Counter display format	Measure/beat

A	Counter display format	Measure/beat

B	Counter display format	Measure/beat

HINT

•If a locate point has not been registered “--” will appear in the numerical ﬁeld.

9

Transport/Locate Operation

AW2400 Owner’s Manual

91

Image 91

Yamaha AW2400 owner manual Adjusting the position of a locate point or marker

Contents

Page Important Notice for the United Kingdom FCC Information U.S.A Important Safety Instructions Precautions Connections Laser properties of the Drive Label shown below is located on the rear of this product Internal Hard Disk Precautions Contents AUX Midi Introduction Before you startRemember to back up your data Handling Using the CD-RW driveAbout the built-inCD-RW drive Using the CD-RW drive About the built-in CD-RW drive Available optional cards Installing an optional cardInstalling an optional card Installing an optional card Before you start Mixer section Features of the AW2400Plenty of input channels with professional features Introducing the AW2400 Recorder section CD-RW drive Connecting to a ComputerAW2400 terminology Recorder section Mixing Layers Mixer sectionLocate points/markers Channels Overall Top panel Parts of the AW2400 and what they doParts of the AW2400 and what they do Work Navigate section Analog Input sectionQuick Navigate section Display section Stereo fader SEL keys Stereo SEL keyOn keys Stereo on key Faders Monitor section Selected Channel sectionScene/Automix/USB section Locate/Number section Data entry/control section Remote key Layer section Transport section Locate section Rear panel Slot Front panel Basic operation of the AW2400 F1-F4 keys correspond to the tabs as follows Accessing a screen/pageSwitching a button on/off Press the key or knob for the desired screen Entering text Using the Locate Keys To Enter Characters & Numbers Using the Selected Channel section Switching Mixing Layers DYN Selected Key Lit Knob Dynamics Screen Introducing the AW2400 Connection Connection and Setup Turning the power on/off Turning the power on/offTurning the power on Turning the power off shut down MIC/LINE Input TRS phone jacks Adjusting the input levelAdjusting the input level MIC/LINE Input XLR jacks Input channel input levels are displayed at the top Song list Listening to the demo songLoading the demo song Press the Work Navigate section Song key Playing the demo song Playing the demo songDemo song will begin playing To stop the song, press the Stop key Mixer section Signal ﬂow when using a sound clipRecording to a sound clip Recording a sound clip Metronome knob TempoTime signature Metronome button Playing a sound clip Playing a sound clipPress the Play key to hear the recorded sound clip Specifying the End point Recording to a sound clip Creating a new song Track recordingMove the cursor to the NEW button and press the Enter key Carry over from the current song, move Select the buttons of the items you want toCursor to the OK button, and press MIC/LINE Input jacks Stereo Output Direct recording and Mixed recordingDirect recording Direct recording and Mixed recording Channel Mixed recordingBus Display will appear as shown here Assigning input signals to tracks Direct recording To Adjust Pan To Adjust Volume/BalanceRaise the Stereo fader to the 0 dB posi- tion This completes the patch setup for direct recording Monitor signal ﬂow during recording Assigning input signals to tracks Mixed recording Set the input channel 1-8 faders as required Press the SEL keys for the record-desti- nation tracks To stop recording, press the Stop key Recording on a trackDirect recording and Mixed recording Recording on a track Recording on a track Saving the current song Saving the current songIf you want to redo the recording, press the UNDO/REDO key Move the cursor to the Save button and press the Enter key Pairing channels Popup window contains the same items as PairingMonitor screen used for channel pairing Popup window will appear, asking you to conﬁrm Repeat steps 5 and 6 to set all bands as required Applying EQ To an Input SignalEQ settings are available via this Applying EQ To an Input Signal Dynamics screen will appear Applying Compression to an Input SignalCompressor settings are available via this Applying Compression to an Input Signal Popup window conﬁrming the recall operation will appear Using the MetronomeActivating the metronome and setting the tempo and vol- ume Handy Recording Functions Time signature can be set from 1/4 to 8/4 Switching virtual tracksTempo map events Tempo can be set from 30 to 250 BPM Undo list Using the Undo ListPress and hold the UNDO/REDO key Undo List popup window will appear Input jacks Track Signal ﬂow when overdubbingOverdubbing About overdubbing Assigning the input signal to a track Assigning the input signal to a track Adjust the pan in the same way for the other track channels Setting the mix balance and panSetting the mix balance and pan Recording will begin OverdubbingOverdubbing Manual punch-in/out Punch-in/outPunch-in/out To rehearse the auto punch-in/out, press the Play key Following diagram shows the auto punch-in/out procedure Overdubbing About mixdown and bouncing Signal ﬂow during mixdown Bouncing differs from mixdown in the following ways Signal ﬂow during bouncingAbout mixdown and bouncing Digital Mixdown procedure Hint Mastering Library popup window will appear Save the song Meter screen Master page will appear Playing back the stereo track Switch the ST TR Mode ON/OFF button onPlaying back the stereo track Record Track Bounce ping-pong recording procedurePlay Track Return Bus 1 and Bus 2 output levels Bounce ping-pong recording procedure Fader Group assignments Convenient functions for mixdown/bounce Operate a channel that is assigned to a mute group Mute Group assignmentsRepeat steps 2-3 to make assignments for other mute groups Buttons E-H can be turned on/off independently Using the Solo function To defeat the Solo function, press the Solo key once again Mixdown and bounce operations Enter the locate point in measures/beats Transport/Locate OperationTransport Section Keys Move To a Speciﬁed Location Using the locator Locate points correspond to the following keys Using the locatorDisplayed Character Locate Type Number Press the Mark key Using markersUsing markers You can assign markers while the song is playing or stopped Adjusting the position of a locate point or marker List Adjusting the position of a markerMarkers Erasing a locate point Erasing a locate point or markerErasing a marker Current location Song track Nudge time AMP Finding a location while viewing the waveformTrack Scale Finding a location while viewing the waveform Level Meter Types Meters Peak Hold button Meter screen Output page F4 keyLevel Meter Types Or by pressing the F1 key after pressing 11 the Record key Patching and signal ﬂowInput signal patching Patching for Direct Recording Multi Connection ON/OFF button Input signal patchingRemain Direct OUT 101 Indication in the screen will be as follows 102 Patching for Mixed RecordingThis area indicates the connection status of tracks 1 This indicates the remaining recordable time For details on recording, refer to Track recording → p Proceed with recording103 ST OUT Assign ﬁeld Output signal patchingOmni OUT Assign ﬁeld Option I/O Slot OUT Assign ﬁeld 105 Channel OperationInput channels Track channels Effect return channels ATT button, EQ button Channel Pair IndicatorPhase button, Gate button Initialize button REC TR CompInsert EFF BUS1, BUS2, ST Source Channel Channel Library OperationCalling the Channel Library screen EQ/COMP Move the cursor to the Store button and press the Enter key Storing Channel Library settings109 Move the cursor to the Clear button and press the Enter key Erasing Channel Library settingsPopup window conﬁrming the clear operation will appear 111 AUX Send Level AdjustmentAdjusting AUX send levels via AUX screen About the AUX buses 112 Adjusting AUX send levels via Selected Channel section Press the Display section F2 key to dis- play the Track Using external effects with the AUX busesThis assigns the AUX1 bus signal to Omni OUT jack AUX1 screen will appear Fully left and right, respectively Signal Flow When Using an External Effect ProcessorEQ key so that its indicator lights, then Press the Selected Channel section PAN Channel Insertion EffectsAbout the Internal Effects Effect Sends and Returns Press the Display section F4 key to call the FX Lib. Recalling Effect Library settingsLibrary setting will be recalled Effect screen will appear 117 Applying Effects via Send and ReturnEffect screen FX Input Input ﬁeld Effect screen FX Track Track ﬁeld Effect screen FX Edit page will appear Select PRE for pre-fader or Post for post-fader send118 119 Signal ﬂow for the selected channel will be dis- playedInserting an Effect Into a Channel Popup window includes the following items 120 Signal ﬂow is as followsInternal effect inserted pre-EQ input channel External effect inserted pre-EQ Input channel Used AS Editing EffectsName Type 122 Effect Library OperationsCall the Effect Library Screen Changing Effect Library Names Cursor to the OK button and press Enter key 123 Storing Effect Library settingsErasing Effect Library settings To actually erase the selected setting move 124 Correcting a Vocal Track Pitch FixCorrecting a Vocal Track Pitch Fix Parameters ﬁeld This will select the Pitch FIX displayPitch FIX ﬁeld Control ﬁeld 126 Master Tuning ﬁeldFIX Note ﬁeld Move the cursor to the Exit button and press Enter About the AW2400’s tracks Track operations and editing127 About audio tracks Audio track operationsViewing all audio tracks Indicates the track number Switching the virtual track of an audio trackMuting a speciﬁc audio track Virtual track name Edited name will be applied Stereo track operationsEditing virtual track names for an audio track About the stereo track Playing back the stereo track Recording on the stereo track131 Editing the name of a virtual track for the stereo track Switching the virtual track of the stereo track132 Trigger Track Function Trigger Track FunctionAbout Trigger Track 133 Fader Start button Normal buttonTrigger button Group Editing tracks Select the editing command Basic procedure for track editing136 Select the virtual track that you want to edit Execute the commandSelect the tracks to edit Specify the editing region Parameter list List of editing commandParameters are the same as for the Erase command List of editing command Start End From Track To Start 139From Track From Track To Start List of editing command When measure lock = on140 Measure Lock Start End From Track To Start 141 Time Compression/ExpansionIf you set Ratio = 50% If you set Ratio = 200% 142 Pitch Pitch Change You can import data from the following types of media Press the Enter key to conﬁrm the edit commandImporting audio data/WAV ﬁles Insert a CD into the CD-RW drive Total File144 Sort Importing audio data from another song145 146 To TR/To V.TR Pan Control via the PAN/EQ Screen Pan Control147 Pan Control via Selected Channel section Adjusting pan via Selected Channel section knob148 EQ Control via the PAN/EQ Screen Band EQ149 EQ Control via the Selected Channel section 151 Using the GatesDynamics Processing Parameter Position ﬁeld Using the CompressorsCompressor Control via Dynamics screen Compt ON/OFF button Threshold Ratio Gain Compressor Control via Selected Channel section153 Selected Channel Knobs Parameters 154 Recalling EQ Library settingsRecalling Gate Library settings EQ/Dynamics Processor Library Operation 155 156 Recalling EQ/Dynamics Library settingsAccess the page containing the library to be edited Changing EQ/Dynamics Library Names 157 Storing EQ/Dynamics Library settingsErasing EQ/Dynamics Library settings Cursor to the OK button and press 158 Protect button Scene MemoryAbout Scene Memory Scene Memory Operation Key. For details on entering a name Renaming a sceneRecalling scene data To the OK button and press the Enter Here’s how you can delete unwanted scene data Storing scene dataDeleting scene data Scene will be stored 162 Using the Recall Safe function 163 Moving scenesSource list Destination list 164 Song Bit Depth Song managementAbout songs Song Organization AW2400-1 Drive AW2400-2 Drive Song Folder Organization166 About songs 167 Managing Your Songs 168 Creating a new songChanges the order of songs displayed in the Song List Currently-selected song Editing the song name Song screen Setting page will appear169 Saving the current song Loading and Sorting Songs170 171 Deleting a songCopying a song Move the cursor to the Copy button and press the Enter key 172 Song ProtectionOptimizing a song Popup window will ask you to conﬁrm the optimize operation 173 Importing data from an existing song ABS absolute time Editing various settings for the songEditing various settings for the song 174 Measure Creating a tempo mapEditing a tempo map event Step Selected event will be deleted Event Range ContentAdding a tempo map event Deleting a tempo map event 177 Backing up songs 178 Restoring songsBacking up songs Restoring songs Restoring songs Restore buttonSystem button 179 180 Mark will appear for songs selected to be restoredCompatible with the other AW-series Information will be read from the inserted CD-R/RW media Automix Operation ENABLE/DISABLE buttonAutomix About Automix Free Command ﬁeldCreating a New Automix Recording Overwrite ﬁeld 183 Move the cursor to the Mode ﬁeld and press the REC buttonRecording the Automix Data Press the top-panel Play key to start song playback PAN CH ON/FADERAUX/EFFECT Send on AUX/EFFECT Send Return Time Operation Automix PlaybackPunch In and Out of Automix To stop Automix playback press the top- panel Stop key Operate the fader as required Command Editing Automix data In a Speciﬁed RegionMove the cursor to the Mode ﬁeld and turn the REC button on Recorded Automix data will be updated Channel/Region CommandWhen the Erase command is selected When the Copy or Move command is selected Param Editing Individual Automix Events188 189 Time Protect Automix Library OperationAbout the Automix Library Changing Automix Names 191 Storing Automix settingsRecalling Automix settings Erasing Automix settings 192 Protecting Automix Data 193 What you can do using Midi Control Change ﬁeld Basic Midi SettingsPort ﬁeld Program Change ﬁeld When Control Change Mode = Control Change Mode box195 CC# Parameter 196 197 198 Midi Synchronization Message Setup 199 Offset Turn on the Slave button in the MMC ﬁeld Connecting to External EquipmentConnecting to External Equipment This sets the AW2400 to function as MTC master Scene Assign scenes to program changesPlay back the external Midi device Program change number Computer-based Sequencer application ChangesMidi Clock Control Changes With a built-in sequencer Play back the AW2400 song from the begin- ning Select a Control Change Mode203 Messages that can Using the Midi Remote functionUsing the Midi Remote function presets About the Midi Remote function Cubase Logic Sonar Protools Mode boxVolume/Rec TR Volume USER1 USER2 USER3 USER4 Using User-deﬁned Remote function206 Midi message This enables the Remote functionRemotely controlling Tone generator module Learn button 208 Operate the AW2400 faders and on keys 209 Using the test tone oscillatorUtility functions Waveform Preroll Time Nudge Play ModeAW2400 Preferences Nudge Time Direct OUT Extract Position Postroll Time211 212 Initializing the internal hard diskCluster ﬁeld Set the disk cluster size to either 32K or 64K CD-RW Creating an audio CDCreating an audio CD CD-R 214 Writing an audio CDTrack At Once Disc At Once Basic settings for the CD-RW drive 216 Writing audio dataIf you turn on Track AT Once button If you turn on the Disc AT Once button 217 Writing Track At OnceInserted CD-RW will be automatically checked Move the cursor to the ADD button and press the Enter key OK button and press the Enter key Writing Disc At OnceMove the cursor to the Write button and press the Enter key To ﬁnalize the disc, move the cursor to 219 Finalizing CD-R/RW media Finalizing CD-R/RW mediaPopup window will ask you to conﬁrm the ﬁnalize operation 220 Erasing CD-RW media Erasing CD-RW mediaButtons select the following erasure methods 221 Input CH MUTE/MIX button CD Play Mode buttonSwitches the CD Play function on/off Playing an audio CD Select the Wordclock Source Wordclock and Cascade Settings223 IN, OUT INT buttonST in button 2-15/16 buttons AW2400 As Wordclock Master Using an HDR or DAW As Wordclock MasterUsing an MD or DAT Recorder as Wordclock Master Select a wordclock source via the Wordclock Source ﬁeld 226 Cascade-connecting External Devices 227 Check the Status Of the Digital Input Signal 228 Plug-in Card SettingsDigital Stereo in connector status Digital I/O card status What You Can Do With USB Midi Message Transfer Normal ModeWAV File Transfer USB Storage Mode USB Storage mode Mode WAV File Transfer USB Storage Mode230 231 Turn on the AW2400Two windows will appear Case of Mac OS Case of Mac OSX Exiting the USB Storage Mode File Name Copying Exported WAV Files To the ComputerFrom TR From V.TR 234 For details on how to enter a name, refer toImporting Copied WAV Files From the Computer Transport folder is located in the AW2400-2 drive 235 This ﬁeld is for display only, and cannot be changed 236 237 AppendixName Description Parameter # Title 238EQ Parameter list Title Parameter LOW MID 239 Parameter Value 240Dynamics Parameters Compressor CMP parameters Expander EXP parameters 241CompanderH CPH CompanderS CPS parameters Gate GAT and Ducking DUK parameters 242 Gate Parameter list Compressor Parameter list 243Title Type Parameter Value Compressor Parameter list 244 Gate REVERB, Reverse Gate Reverb HALL, Reverb ROOM, Reverb STAGE, Reverb PlateEarly REF One input, two output early reﬂections Delay LCR Mono DelayStereo Delay MOD. Delay 247 EchoChorus Flange 248 PhaserSymphonic Auto PAN Rotary TremoloHQ. Pitch Dual Pitch AMP Simulate Ring MODMOD. Filter Distortion 251 DYNA. PhaserDYNA. Filter DYNA. Flange 252 REV+CHORUSREV-CHORUS REV+FLANGE REV-SYMPHO REV-FLANGEOne input, two output reverb and ﬂanger effects in series REV+SYMPHO REV-PAN DELAY+ER254 255 DELAY-ERDELAY+REV DELAY-REV 256 DIST-DELAYMulti Filter Two input, two output 3-band multi-ﬁlter 24 dB/octave Band Dyna Gate257 258 259 260 261 262 263 MessagesDisplay message list 264 Popup messages 265 Installing USB Midi driver Contents of the CD-ROMSpecial Notices Click the Close button Start your computer, then log in as Adminis- tratorRestart the computer Click Continue Windows Installing a remote ﬁleMove the cursor to the list and press 268 269 Commands 270 Installing the Sonar template ﬁle Type Receive From Send To #ch’s 271 Control Change Mode Program Change Mode272 MTC Sync Offset MTC Sync ModeRemote Port MTC Sync Average Continue FB Midi Time Code Quarter Frame F1Song Position Pointer F2 Timing Clock F8 MMC Locate Target MMC Fast ForwardMMC Record Strobe MMC Record Exit 276 Midi Implementation Chart 277 Digital Mixing Functions Input/Output278 279 Dimensions Index 280 Gate 281 Recall Confirmation 282 283 Input Block diagram 285 286 North America