Rev-Pan, Delay+Er, 254 | Yamaha AW2400 guide

Effects Parameters

■REV->PAN

One input, two output reverb and autopan effects in parallel.

Parameter	Range	Description

REV TIME	0.3–99.0 s	Reverb time

INI. DLY	0.0–500.0 ms	Initial delay before reverb begins

HI. RATIO	0.1–1.0	High-frequency reverb time ratio

DIFF.	0–10	Spread

DENSITY	0–100%	Reverb density

HPF	THRU, 21.2 Hz–8.00 kHz	High-pass ﬁlter cutoff frequency

LPF	50.0 Hz–16.0 kHz, THRU	Low-pass ﬁlter cutoff frequency

REV.BAL	0–100%	Reverb and panned reverb balance (0% = all panned reverb, 100% = all reverb)

FREQ.	0.05–40.00 Hz	Modulation speed

DEPTH	0–100%	Modulation depth

DIR.	*1	Panning direction

WAVE	Sine, Tri, Square	Modulation waveform

*1. L<–>R, L–>R, L<–R, Turn L, Turn R

■DELAY+ER.

One input, two output delay and early reﬂections effects in parallel.

	Parameter	Range	Description

	DELAY L	0.0–1000.0 ms	Left channel delay time

	DELAY R	0.0–1000.0 ms	Right channel delay time

	FB. DLY	0.0–1000.0 ms	Feedback delay time

	FB. GAIN	-99 to +99%	Feedback gain (plus values for normal-phase feedback, minus values for reverse-phase feedback)

	HI. RATIO	0.1–1.0	High-frequency feedback ratio

	HPF	THRU, 21.2 Hz–8.00 kHz	High-pass ﬁlter cutoff frequency

	LPF	50.0 Hz–16.0 kHz, THRU	Low-pass ﬁlter cutoff frequency

	DLY/ER	0–100%	Delay and early reﬂections balance (0% = all delay, 100% = all early reﬂections)

	TYPE	S-Hall, L-Hall, Random,	Type of early reﬂection simulation
	TYPE	Revers, Plate, Spring	Type of early reﬂection simulation
		Revers, Plate, Spring

	ROOMSIZE	0.1–20.0	Reﬂection spacing

	LIVENESS	0–10	Early reﬂections decay characteristics (0 = dead, 10 = live)

	INI. DLY	0.0–500.0 ms	Initial delay before reverb begins

	DIFF.	0–10	Spread

	DENSITY	0–100%	Reverb density

	ER NUM.	1–19	Number of early reﬂections

Appendix

254

AW2400 Owner’s Manual

Image 254

Yamaha AW2400 owner manual Rev-Pan, Delay+Er, 254

Contents

Page FCC Information U.S.A Important Notice for the United Kingdom Important Safety Instructions Precautions Connections Label shown below is located on the rear of this product Laser properties of the Drive Internal Hard Disk Precautions Contents AUX Midi Remember to back up your data Before you startIntroduction About the built-in CD-RW drive Using the CD-RW driveAbout the built-inCD-RW drive Using the CD-RW drive Handling Installing an optional card Installing an optional cardInstalling an optional card Available optional cards Before you start Introducing the AW2400 Features of the AW2400Plenty of input channels with professional features Mixer section Recorder section Recorder section Connecting to a ComputerAW2400 terminology CD-RW drive Channels Mixer sectionLocate points/markers Mixing Layers Overall Parts of the AW2400 and what they do Parts of the AW2400 and what they doTop panel Quick Navigate section Analog Input sectionWork Navigate section Display section Faders SEL keys Stereo SEL keyOn keys Stereo on key Stereo fader Scene/Automix/USB section Selected Channel sectionMonitor section Data entry/control section Locate/Number section Layer section Remote key Locate section Transport section Rear panel Front panel Slot Basic operation of the AW2400 Press the key or knob for the desired screen Accessing a screen/pageSwitching a button on/off F1-F4 keys correspond to the tabs as follows Using the Locate Keys To Enter Characters & Numbers Entering text Switching Mixing Layers Using the Selected Channel section Selected Key Lit Knob DYN Dynamics Screen Introducing the AW2400 Connection and Setup Connection Turning the power off shut down Turning the power on/offTurning the power on Turning the power on/off MIC/LINE Input XLR jacks Adjusting the input levelAdjusting the input level MIC/LINE Input TRS phone jacks Input channel input levels are displayed at the top Press the Work Navigate section Song key Listening to the demo songLoading the demo song Song list To stop the song, press the Stop key Playing the demo songDemo song will begin playing Playing the demo song Recording a sound clip Signal ﬂow when using a sound clipRecording to a sound clip Mixer section Metronome button TempoTime signature Metronome knob Specifying the End point Playing a sound clipPress the Play key to hear the recorded sound clip Playing a sound clip Recording to a sound clip Move the cursor to the NEW button and press the Enter key Track recordingCreating a new song Cursor to the OK button, and press Select the buttons of the items you want toCarry over from the current song, move Direct recording and Mixed recording Direct recording and Mixed recordingDirect recording MIC/LINE Input jacks Stereo Output Bus Mixed recordingChannel Assigning input signals to tracks Direct recording Display will appear as shown here Raise the Stereo fader to the 0 dB posi- tion To Adjust Volume/BalanceTo Adjust Pan Monitor signal ﬂow during recording This completes the patch setup for direct recording Assigning input signals to tracks Mixed recording Press the SEL keys for the record-desti- nation tracks Set the input channel 1-8 faders as required Direct recording and Mixed recording Recording on a track Recording on a trackTo stop recording, press the Stop key Move the cursor to the Save button and press the Enter key Saving the current songIf you want to redo the recording, press the UNDO/REDO key Recording on a track Saving the current song Pairing channels Popup window will appear, asking you to conﬁrm PairingMonitor screen used for channel pairing Popup window contains the same items as Applying EQ To an Input Signal Applying EQ To an Input SignalEQ settings are available via this Repeat steps 5 and 6 to set all bands as required Applying Compression to an Input Signal Applying Compression to an Input SignalCompressor settings are available via this Dynamics screen will appear Handy Recording Functions Using the MetronomeActivating the metronome and setting the tempo and vol- ume Popup window conﬁrming the recall operation will appear Tempo can be set from 30 to 250 BPM Switching virtual tracksTempo map events Time signature can be set from 1/4 to 8/4 Undo List popup window will appear Using the Undo ListPress and hold the UNDO/REDO key Undo list About overdubbing Signal ﬂow when overdubbingOverdubbing Input jacks Track Assigning the input signal to a track Assigning the input signal to a track Setting the mix balance and pan Setting the mix balance and panAdjust the pan in the same way for the other track channels Overdubbing OverdubbingRecording will begin Punch-in/out Punch-in/outManual punch-in/out To rehearse the auto punch-in/out, press the Play key Following diagram shows the auto punch-in/out procedure Overdubbing Signal ﬂow during mixdown About mixdown and bouncing About mixdown and bouncing Signal ﬂow during bouncingBouncing differs from mixdown in the following ways Mixdown procedure Digital Mastering Library popup window will appear Hint Meter screen Master page will appear Save the song Playing back the stereo track Switch the ST TR Mode ON/OFF button onPlaying back the stereo track Return Bounce ping-pong recording procedurePlay Track Record Track Bus 1 and Bus 2 output levels Bounce ping-pong recording procedure Convenient functions for mixdown/bounce Fader Group assignments Buttons E-H can be turned on/off independently Mute Group assignmentsRepeat steps 2-3 to make assignments for other mute groups Operate a channel that is assigned to a mute group Using the Solo function To defeat the Solo function, press the Solo key once again Mixdown and bounce operations Move To a Speciﬁed Location Transport/Locate OperationTransport Section Keys Enter the locate point in measures/beats Using the locator Displayed Character Locate Type Number Using the locatorLocate points correspond to the following keys You can assign markers while the song is playing or stopped Using markersUsing markers Press the Mark key Adjusting the position of a locate point or marker Markers Adjusting the position of a markerList Erasing a marker Erasing a locate point or markerErasing a locate point Current location Song track Nudge time Scale Finding a location while viewing the waveformTrack AMP Finding a location while viewing the waveform Meters Level Meter Types Level Meter Types Meter screen Output page F4 keyPeak Hold button Patching for Direct Recording Patching and signal ﬂowInput signal patching Or by pressing the F1 key after pressing 11 the Record key Direct OUT Input signal patchingRemain Multi Connection ON/OFF button Indication in the screen will be as follows 101 This indicates the remaining recordable time Patching for Mixed RecordingThis area indicates the connection status of tracks 1 102 103 Proceed with recordingFor details on recording, refer to Track recording → p Option I/O Slot OUT Assign ﬁeld Output signal patchingOmni OUT Assign ﬁeld ST OUT Assign ﬁeld Track channels Effect return channels Channel OperationInput channels 105 Initialize button Channel Pair IndicatorPhase button, Gate button ATT button, EQ button BUS1, BUS2, ST CompInsert EFF REC TR EQ/COMP Channel Library OperationCalling the Channel Library screen Source Channel 109 Storing Channel Library settingsMove the cursor to the Store button and press the Enter key Popup window conﬁrming the clear operation will appear Erasing Channel Library settingsMove the cursor to the Clear button and press the Enter key About the AUX buses AUX Send Level AdjustmentAdjusting AUX send levels via AUX screen 111 Adjusting AUX send levels via Selected Channel section 112 AUX1 screen will appear Using external effects with the AUX busesThis assigns the AUX1 bus signal to Omni OUT jack Press the Display section F2 key to dis- play the Track Press the Selected Channel section PAN Signal Flow When Using an External Effect ProcessorEQ key so that its indicator lights, then Fully left and right, respectively Effect Sends and Returns EffectsAbout the Internal Effects Channel Insertion Effect screen will appear Recalling Effect Library settingsLibrary setting will be recalled Press the Display section F4 key to call the FX Lib. Effect screen FX Track Track ﬁeld Applying Effects via Send and ReturnEffect screen FX Input Input ﬁeld 117 118 Select PRE for pre-fader or Post for post-fader sendEffect screen FX Edit page will appear Popup window includes the following items Signal ﬂow for the selected channel will be dis- playedInserting an Effect Into a Channel 119 External effect inserted pre-EQ Input channel Signal ﬂow is as followsInternal effect inserted pre-EQ input channel 120 Type Editing EffectsName Used AS Changing Effect Library Names Effect Library OperationsCall the Effect Library Screen 122 To actually erase the selected setting move Storing Effect Library settingsErasing Effect Library settings Cursor to the OK button and press Enter key 123 Correcting a Vocal Track Pitch Fix Correcting a Vocal Track Pitch Fix124 Control ﬁeld This will select the Pitch FIX displayPitch FIX ﬁeld Parameters ﬁeld Move the cursor to the Exit button and press Enter Master Tuning ﬁeldFIX Note ﬁeld 126 127 Track operations and editingAbout the AW2400’s tracks Viewing all audio tracks Audio track operationsAbout audio tracks Virtual track name Switching the virtual track of an audio trackMuting a speciﬁc audio track Indicates the track number About the stereo track Stereo track operationsEditing virtual track names for an audio track Edited name will be applied 131 Recording on the stereo trackPlaying back the stereo track 132 Switching the virtual track of the stereo trackEditing the name of a virtual track for the stereo track 133 Trigger Track FunctionAbout Trigger Track Trigger Track Function Group Normal buttonTrigger button Fader Start button Editing tracks 136 Basic procedure for track editingSelect the editing command Specify the editing region Execute the commandSelect the tracks to edit Select the virtual track that you want to edit List of editing command List of editing commandParameters are the same as for the Erase command Parameter list From Track 139Start End From Track To Start Measure Lock Start End From Track To Start List of editing command When measure lock = on140 From Track To Start If you set Ratio = 200% Time Compression/ExpansionIf you set Ratio = 50% 141 Pitch Pitch Change 142 Insert a CD into the CD-RW drive Press the Enter key to conﬁrm the edit commandImporting audio data/WAV ﬁles You can import data from the following types of media 144 FileTotal 145 Importing audio data from another songSort To TR/To V.TR 146 147 Pan ControlPan Control via the PAN/EQ Screen 148 Adjusting pan via Selected Channel section knobPan Control via Selected Channel section 149 Band EQEQ Control via the PAN/EQ Screen EQ Control via the Selected Channel section Parameter Using the GatesDynamics Processing 151 Compt ON/OFF button Using the CompressorsCompressor Control via Dynamics screen Position ﬁeld Selected Channel Knobs Parameters Compressor Control via Selected Channel section153 Threshold Ratio Gain EQ/Dynamics Processor Library Operation Recalling EQ Library settingsRecalling Gate Library settings 154 155 Changing EQ/Dynamics Library Names Recalling EQ/Dynamics Library settingsAccess the page containing the library to be edited 156 Cursor to the OK button and press Storing EQ/Dynamics Library settingsErasing EQ/Dynamics Library settings 157 158 Scene Memory Operation Scene MemoryAbout Scene Memory Protect button To the OK button and press the Enter Renaming a sceneRecalling scene data Key. For details on entering a name Scene will be stored Storing scene dataDeleting scene data Here’s how you can delete unwanted scene data Using the Recall Safe function 162 Destination list Moving scenesSource list 163 164 Song Organization Song managementAbout songs Song Bit Depth About songs Song Folder Organization166 AW2400-1 Drive AW2400-2 Drive Managing Your Songs 167 Currently-selected song Creating a new songChanges the order of songs displayed in the Song List 168 169 Song screen Setting page will appearEditing the song name 170 Loading and Sorting SongsSaving the current song Move the cursor to the Copy button and press the Enter key Deleting a songCopying a song 171 Popup window will ask you to conﬁrm the optimize operation Song ProtectionOptimizing a song 172 Importing data from an existing song 173 174 Editing various settings for the songEditing various settings for the song ABS absolute time Step Creating a tempo mapEditing a tempo map event Measure Deleting a tempo map event Event Range ContentAdding a tempo map event Selected event will be deleted Backing up songs 177 Backing up songs Restoring songs Restoring songs178 179 Restore buttonSystem button Restoring songs Information will be read from the inserted CD-R/RW media Mark will appear for songs selected to be restoredCompatible with the other AW-series 180 About Automix ENABLE/DISABLE buttonAutomix Automix Operation Overwrite ﬁeld Command ﬁeldCreating a New Automix Recording Free Press the top-panel Play key to start song playback Move the cursor to the Mode ﬁeld and press the REC buttonRecording the Automix Data 183 AUX/EFFECT Send CH ON/FADERAUX/EFFECT Send on PAN To stop Automix playback press the top- panel Stop key Automix PlaybackPunch In and Out of Automix Return Time Operation Recorded Automix data will be updated Command Editing Automix data In a Speciﬁed RegionMove the cursor to the Mode ﬁeld and turn the REC button on Operate the fader as required When the Copy or Move command is selected CommandWhen the Erase command is selected Channel/Region 188 Editing Individual Automix EventsParam Time 189 Changing Automix Names Automix Library OperationAbout the Automix Library Protect Erasing Automix settings Storing Automix settingsRecalling Automix settings 191 Protecting Automix Data 192 What you can do using Midi 193 Program Change ﬁeld Basic Midi SettingsPort ﬁeld Control Change ﬁeld 195 Control Change Mode boxWhen Control Change Mode = 196 CC# Parameter 197 Midi Synchronization Message Setup 198 Offset 199 This sets the AW2400 to function as MTC master Connecting to External EquipmentConnecting to External Equipment Turn on the Slave button in the MMC ﬁeld Program change number Assign scenes to program changesPlay back the external Midi device Scene With a built-in sequencer ChangesMidi Clock Control Changes Computer-based Sequencer application 203 Select a Control Change ModePlay back the AW2400 song from the begin- ning About the Midi Remote function Using the Midi Remote functionUsing the Midi Remote function presets Messages that can Volume Mode boxVolume/Rec TR Cubase Logic Sonar Protools 206 Using User-deﬁned Remote functionUSER1 USER2 USER3 USER4 Learn button This enables the Remote functionRemotely controlling Tone generator module Midi message Operate the AW2400 faders and on keys 208 Waveform Using the test tone oscillatorUtility functions 209 Nudge Time Nudge Play ModeAW2400 Preferences Preroll Time 211 Postroll TimeDirect OUT Extract Position Set the disk cluster size to either 32K or 64K Initializing the internal hard diskCluster ﬁeld 212 CD-R Creating an audio CDCreating an audio CD CD-RW Disc At Once Writing an audio CDTrack At Once 214 Basic settings for the CD-RW drive If you turn on the Disc AT Once button Writing audio dataIf you turn on Track AT Once button 216 Move the cursor to the ADD button and press the Enter key Writing Track At OnceInserted CD-RW will be automatically checked 217 To ﬁnalize the disc, move the cursor to Writing Disc At OnceMove the cursor to the Write button and press the Enter key OK button and press the Enter key 219 220 Finalizing CD-R/RW mediaPopup window will ask you to conﬁrm the ﬁnalize operation Finalizing CD-R/RW media 221 Erasing CD-RW mediaButtons select the following erasure methods Erasing CD-RW media Playing an audio CD CD Play Mode buttonSwitches the CD Play function on/off Input CH MUTE/MIX button 223 Wordclock and Cascade SettingsSelect the Wordclock Source 2-15/16 buttons INT buttonST in button IN, OUT Select a wordclock source via the Wordclock Source ﬁeld Using an HDR or DAW As Wordclock MasterUsing an MD or DAT Recorder as Wordclock Master AW2400 As Wordclock Master Cascade-connecting External Devices 226 Check the Status Of the Digital Input Signal 227 Digital I/O card status Plug-in Card SettingsDigital Stereo in connector status 228 USB Storage mode Midi Message Transfer Normal ModeWAV File Transfer USB Storage Mode What You Can Do With USB 230 WAV File Transfer USB Storage ModeMode Case of Mac OS Turn on the AW2400Two windows will appear 231 Exiting the USB Storage Mode Case of Mac OSX From V.TR Copying Exported WAV Files To the ComputerFrom TR File Name Transport folder is located in the AW2400-2 drive For details on how to enter a name, refer toImporting Copied WAV Files From the Computer 234 This ﬁeld is for display only, and cannot be changed 235 236 Name Description Appendix237 Title Parameter 238EQ Parameter list Parameter # Title 239 LOW MID Compressor CMP parameters 240Dynamics Parameters Parameter Value CompanderH CPH CompanderS CPS parameters 241Expander EXP parameters 242 Gate GAT and Ducking DUK parameters Title Type Parameter Value 243Gate Parameter list Compressor Parameter list 244 Compressor Parameter list One input, two output early reﬂections Reverb HALL, Reverb ROOM, Reverb STAGE, Reverb PlateEarly REF Gate REVERB, Reverse Gate MOD. Delay Mono DelayStereo Delay Delay LCR Flange EchoChorus 247 Auto PAN PhaserSymphonic 248 Dual Pitch TremoloHQ. Pitch Rotary Distortion Ring MODMOD. Filter AMP Simulate DYNA. Flange DYNA. PhaserDYNA. Filter 251 REV+FLANGE REV+CHORUSREV-CHORUS 252 REV+SYMPHO REV-FLANGEOne input, two output reverb and ﬂanger effects in series REV-SYMPHO 254 DELAY+ERREV-PAN DELAY-REV DELAY-ERDELAY+REV 255 Two input, two output 3-band multi-ﬁlter 24 dB/octave DIST-DELAYMulti Filter 256 257 GateBand Dyna 258 259 260 261 262 Display message list Messages263 Popup messages 264 265 Special Notices Contents of the CD-ROMInstalling USB Midi driver Click Continue Start your computer, then log in as Adminis- tratorRestart the computer Click the Close button 268 Installing a remote ﬁleMove the cursor to the list and press Windows Commands 269 Installing the Sonar template ﬁle 270 271 Type Receive From Send To #ch’s 272 Program Change ModeControl Change Mode MTC Sync Average MTC Sync ModeRemote Port MTC Sync Offset Timing Clock F8 Midi Time Code Quarter Frame F1Song Position Pointer F2 Continue FB MMC Record Exit MMC Fast ForwardMMC Record Strobe MMC Locate Target Midi Implementation Chart 276 277 278 Input/OutputDigital Mixing Functions Dimensions 279 280 Index 281 Gate 282 Recall Confirmation 283 Block diagram Input 285 286 North America