Samsung SSA-S2000W user manual Installation and External Connection

Page 10

installation and external connection

INSTALLING THE REAR TEMPLATE

	6-32 hole
O-ring	O-ring
	1/2” hole

O-ring
O-ring	6-32 hole
	6-32 hole

1.79"(45.5mm)1.55"(39.5mm)

1.85"(47mm)

2.05"(52mm)

O-ring

1.52"(38.5mm) 1.52"(38.5mm)

3.03"(77mm)

J Once the main unit is ﬁxed with the rear panel, it will not be loosened. Please check if the device is operating before ﬁxing it. If you try to remove the rear panel once it is ﬁxed, the lock parts of the rear panel will break, resulting in a situation where the whole rear panel must be replaced.

10_ Installation and External Connection

Image 10

Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the use of the tamper alarm To specify the input mode for AUXTo specify the input mode for the Door Contact Sensor alarmFeatures Product introductionQuick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables AT a Glance Front ViewCable Color Scheme Installation and External Connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened Brown line with white stripes Wiegand Output SetupInitialization TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyEnabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorDefault is set to not used To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Buttons and press ENTTo Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O Time Setup \ ` To Specify the TTL Output Operation Mode Advanced settingTo SET the Chime Bell Function To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time36 고급 설정 To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorTo Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Other information Initial ValuesFunction Codes Sense if AUX 2 switches from L to H Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from H to LTroubleshooting TroubleshootingTroubleshooting √ RF OnlyEInstall and use the product as usual √ Enter the command to delete the user 14 + ENTService center Check the operation status of the productUser cards to the factory default Using the keypadUnregistered numbers in 5 consecutive times default CIf SSA-S2000 responds when you press the Exit buttonS2000 Irrelevant data is transferredDisconnection or short-circuit Consult with a qualiﬁed technicianProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product