Samsung SSA-S2000W user manual To Check the Output Specified for a Registered Card User

Page 39

TO CHECK THE OUTPUT SPECIFIED FOR A REGISTERED CARD USER

You can check the output setting that you speciﬁed in “To specify the output time if the card is authenticated”. (See page 29.)

1. Present the Master Card to the device.

	X	Y	Z
2. Press Button 3 and Button 1 in sequence and press ENT .		\	]
2. Press Button 3 and Button 1 in sequence and press ENT .			`
t
Gj	lzj	W	lu{

	i
			zzhTzYWWW
	X	Y	Z
		\	]
	^	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

ADDITIONAL FEATURES

TO CHECK THE OUTPUT SPECIFIED FOR AN UNREGISTERED CARD USER

You can check the output setting that you speciﬁed in “To specify the output time if the card is not authenticated”. (See page 30.)

1. Present the Master Card to the device.

	X	Y	Z
2. Press Button 3 and Button 2 and Button ENT .		\	]
2. Press Button 3 and Button 2 and Button ENT .			`
tGj	lzj	W	lu{
	lzj	W	lu{
	i
			zzhTzYWWW
	X	Y	Z
		\	]
	^	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

English _ 39

Image 39

Contents Imagine the possibilities Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarmProduct introduction FeaturesWHAT’S Included Quick Guide Rings Diodes UF4004, 1N4001~4007Master Card Cables Front View AT a GlanceCable Color Scheme Installation and External Connection DC12V Cable SelectionConnection Bypass Diode ConnectionOutput Connection External Reader Connection Initialization Basic OperationsIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripesHardware Forcible Initialization Forced Initialization with External LineReader mode setup Reader Mode Setup RF onlyNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WReader Mode Setup RF/PIN Combination Mode Enabling Keypad Input for the Card NumberButton To Register Cards in RF only Mode User managementRegistering Cards in a Combination of RF and P/W Modes To Register Cards in PIN Mode Registering Cards in RF Card / PIN Combination ModeMaster PIN To Delete a Registered Card or PIN Number Basic setup Duress AlarmTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure ModeTo Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact SensorTo Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled DeviceButtons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not usedTime setup To Specify the Output Time if the Card is AuthenticatedYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not AuthenticatedEnter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX32 I/O Time Setup \ ` Advanced setting To Specify the TTL Output Operation ModeTo SET the Chime Bell Function To Specify the Chime Bell Operation Time To Specify the Input Mode for AUX36 고급 설정 To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit ButtonAdditional features To Specify the USE of the Tamper AlarmMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Initial Values Other informationFunction Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to HTroubleshooting Troubleshooting√ RF Only TroubleshootingCheck the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usualCIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory defaultConsult with a qualiﬁed technician Irrelevant data is transferredDisconnection or short-circuit S2000Product speciﬁcations Product SpecificationsCorrect disposal of batteries in this product