Samsung SSA-S2000W user manual Safety information

Page 2

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

1.Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.

2.Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock.

3.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

4.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage to the product.

2_ Safety information

Image 2
Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the use of the tamper alarm To specify the input mode for AUXTo specify the input mode for the Door Contact Sensor alarmFeatures Product introductionMaster Card Cables WHAT’S IncludedQuick Guide Rings Diodes UF4004, 1N4001~4007 AT a Glance Front ViewCable Color Scheme Installation and External Connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection If you press the Exit button, the door will be opened InitializationBasic Operations Brown line with white stripes Wiegand Output SetupInitialization TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationNo Master Card or Master PIN is ever registered Reader mode setupReader Mode Setup RF only Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyButton Reader Mode Setup RF/PIN Combination ModeEnabling Keypad Input for the Card Number Registering Cards in a Combination of RF and P/W Modes To Register Cards in RF only ModeUser management Master PIN To Register Cards in PIN ModeRegistering Cards in RF Card / PIN Combination Mode To Delete a Registered Card or PIN Number To Specify the Retry Count for AN Unregistered ID Basic setupDuress Alarm To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorDefault is set to not used To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Buttons and press ENTYou can specify from 10 to Time setupTo Specify the Output Time if the Card is Authenticated To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O Time Setup \ ` To SET the Chime Bell Function Advanced settingTo Specify the TTL Output Operation Mode To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time36 고급 설정 To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorMute Additional featuresTo Specify the USE of the Tamper Alarm To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Other information Initial ValuesFunction Codes Sense if AUX 2 switches from L to H Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from H to LTroubleshooting TroubleshootingTroubleshooting √ RF OnlyEInstall and use the product as usual √ Enter the command to delete the user 14 + ENTService center Check the operation status of the productUser cards to the factory default Using the keypadUnregistered numbers in 5 consecutive times default CIf SSA-S2000 responds when you press the Exit buttonS2000 Irrelevant data is transferredDisconnection or short-circuit Consult with a qualified technicianProduct Specifications Product specificationsCorrect disposal of batteries in this product