Samsung SSA-S2000W user manual Product introduction, Features

Page 6

product introduction

FEATURES

This controller is best designed for a single entry door control (single door access control).

It can store up to 512 cards including the Master Card that enables you to register, delete or set various user cards to your preference.

This product features 5 external ports that can be connected to the Exit button, Door Contact Sensor, Motion Sensor, and Fire Sensor. It also has 2 relay outputs that can control the door lock and alarm relay. The dual tamper switch triggers an alert if the product is forcibly disassembled.

You can use the keypad to conﬁgure all settings as necessary. This product is designed for a standalone system.

Single Door Access Control

You can use the RF card (SSA-C100,SSA-C110,SSA-C120) to control a single door.

User Registration

You can register a total of 512 cards including the Master Card.

Keypad Registration

SSA-S2000 is equipped with the built-in keypad that you can use to register, delete cards or conﬁgure various settings independently.

Buzzer On/Off

With the help of various buzzer tones, you can check the operation status and the current settings and results of the product.

External I/O Pins

SSA-SS2000 has 5 input ports and 4 output ports installed (2 relay and 2 TTL outputs).

The input ports can receive signals from the Exit button and the Door Contact sensor, while the two relays can be connected to the door lock and the alarm device. One of the TTL output ports can function as a chime bell in connection with the door bell.

Duress Alarm

This is used in a situation where you should open the door inevitably by a robber insisting to do so. Entering the two-digit

duress alarm password with pressing the ENT button and recognizing the registered card (or card number) can open the door normally, while you can set to produce the TTL signal notifying the door is forcibly opened.

Limited Access Tries for an Unregistered Card

You can specify the limit of times to try accessing the door, and the suspended operation time of the keypad for an improper access.

6_ Product Introduction

Image 6

Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the use of the tamper alarm To specify the input mode for AUXTo specify the input mode for the Door Contact Sensor alarmFeatures Product introductionWHAT’S Included Quick Guide Rings Diodes UF4004, 1N4001~4007Master Card Cables AT a Glance Front ViewCable Color Scheme Installation and External Connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Initialization Basic OperationsIf you press the Exit button, the door will be opened Brown line with white stripes Wiegand Output SetupInitialization TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader mode setup Reader Mode Setup RF onlyNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyReader Mode Setup RF/PIN Combination Mode Enabling Keypad Input for the Card NumberButton To Register Cards in RF only Mode User managementRegistering Cards in a Combination of RF and P/W Modes To Register Cards in PIN Mode Registering Cards in RF Card / PIN Combination ModeMaster PIN To Delete a Registered Card or PIN Number Basic setup Duress AlarmTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorDefault is set to not used To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Buttons and press ENTTime setup To Specify the Output Time if the Card is AuthenticatedYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O Time Setup \ ` Advanced setting To Specify the TTL Output Operation ModeTo SET the Chime Bell Function To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time36 고급 설정 To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorAdditional features To Specify the USE of the Tamper AlarmMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Other information Initial ValuesFunction Codes Sense if AUX 2 switches from L to H Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from H to LTroubleshooting TroubleshootingTroubleshooting √ RF OnlyEInstall and use the product as usual √ Enter the command to delete the user 14 + ENTService center Check the operation status of the productUser cards to the factory default Using the keypadUnregistered numbers in 5 consecutive times default CIf SSA-S2000 responds when you press the Exit buttonS2000 Irrelevant data is transferredDisconnection or short-circuit Consult with a qualiﬁed technicianProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product