Samsung SSA-S2000W user manual To Register Cards in PIN Mode, Master PIN

Page 22

user management

TO REGISTER CARDS IN PIN MODE

Ensure that you must have registered the Master Card and the device is specified in PIN mode.

1.Enter the Master PIN number and press ENT .

When the mode is specified, only the green LED indicator flashes.

2. Press Button 1 and Button 3 in sequence and press ENT . When the mode is specified, only the green LED indicator flashes.

3.If you enter a user number (4-6 digits) to register and press ENT , the PIN number will be registered with a beep.

Repeat this step if you want to register multiple PIN numbers.

4.Present the Master PIN number to the device again, and the device will switch to normal mode.

If no input is made for 20 seconds, the device will switch to normal mode.

X Y Z

[ \ ]

^ _ `

lzj W lu{

iŒ““

zzhTzYWWW

<Master PIN>

X

Y

Z

Î

X

Y

Z

Î

X

Y

Z

[

\

]

[

\

]

[

\

]

^

_

`

 

^

_

`

 

^

_

`

lzj

W

lu{

 

lzj

W

lu{

 

lzj

W

lu{

iŒ““

 

 

 

iŒ““

 

 

 

iŒ““

 

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

<User Number>

 

<User Number>

 

<Master PIN>

REGISTERING CARDS IN RF CARD / PIN COMBINATION MODE

Ensure that you must have registered the Master Card and the device is specified in RF Card / PIN combination mode.

1.Present the Master Card to the device.

When the mode is specified, only the green LED indicator flashes.

2. Press Button 1 and Button 5 in sequence and press ENT .

When the device enters Standby, only the red LED indicator flashes.

tˆš›Œ™Gjˆ™‹

3.Present cards or PIN numbers (4-6 digits) to register with the device one after another, and the device will register them with a beep.

Repeat this step if you want to register multiple cards or PIN numbers.

4.Present the Master PIN number to the device again, and the device will switch to normal mode. If no input is made for 20 seconds, the device will switch to normal mode.

X Y Z

\ ]

`

lzj W lu{

iŒ““

zzhTzYWWW

X

Y

Z

Î

X

Y

Z

[

\

]

[

\

]

^

_

`

 

^

_

`

lzj

W

lu{

 

 

W

lu{

iŒ““

 

 

 

iŒ““

 

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

or

X

Y

Z

Î

[

\

]

^

_

`

 

lzj

W

lu{

 

iŒ““

 

 

 

 

 

zzhTzYWWW

 

tˆš›Œ™

Gjˆ™‹

X Y Z

\ ]

`

lzj W lu{

iŒ““

zzhTzYWWW

MThe door may be accessed in two ways: using the card or the PIN number.

22_ User Management

Image 22
Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the use of the tamper alarm To specify the input mode for AUXTo specify the input mode for the Door Contact Sensor alarmFeatures Product introductionQuick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables AT a Glance Front ViewCable Color Scheme Installation and External Connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened Brown line with white stripes Wiegand Output SetupInitialization TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyEnabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorDefault is set to not used To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Buttons and press ENTTo Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O Time Setup \ ` To Specify the TTL Output Operation Mode Advanced settingTo SET the Chime Bell Function To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time36 고급 설정 To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorTo Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Other information Initial ValuesFunction Codes Sense if AUX 2 switches from L to H Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from H to LTroubleshooting TroubleshootingTroubleshooting √ RF OnlyEInstall and use the product as usual √ Enter the command to delete the user 14 + ENTService center Check the operation status of the productUser cards to the factory default Using the keypadUnregistered numbers in 5 consecutive times default CIf SSA-S2000 responds when you press the Exit buttonS2000 Irrelevant data is transferredDisconnection or short-circuit Consult with a qualified technicianProduct Specifications Product specificationsCorrect disposal of batteries in this product