Samsung SSA-S2000W user manual Other information, Initial Values

Page 42

other information

INITIAL VALUES

This product operates in the following initial values:

For changing the settings or registering/deleting the user card, refer to the applicable section in this document.

1)Entry permitted for a registered card

-The door control relay operates for 3 seconds.

-The green LED indicator flashes for 3 seconds.

2)Entry denied for an unregistered card

-The alarm relay operates for 2 seconds.

-The red LED indicator flashes for 2 seconds.

3)Duress Mode Password : 00

The TTL output port produces a signal for 3 seconds in Duress mode.

4)QUICK MODE : Disabled

5)Chime Bell Output : Enabled

Chime Bell Operating Time : 0.5 second

6)Melody Sound : Enabled

7)Keypad Input Limited Use : 20 seconds

8)When an input signal is sensed : ‘H’ € ‘L’ (common for all inputs)

9)When a TTL output signal is sensed : ‘H -> L’

10)Patrol Mode Delay Time : 00 minute

11)Door Sensor Sensing Time : 00 second

12)Retry count for an unauthenticated entry : 05 times

13)Alarm for Dismantled Device : Disabled

Dismantled device Alarm Output Port : 02 (Alarm Relay)

14)Toggle Mode : Disabled

15)Control Lock by the Door Sensor : Disabled

42_ Additional Features

Image 42
Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the use of the tamper alarm To specify the input mode for AUXTo specify the input mode for the Door Contact Sensor alarmFeatures Product introductionWHAT’S Included Quick Guide Rings Diodes UF4004, 1N4001~4007Master Card Cables AT a Glance Front ViewCable Color Scheme Installation and External Connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Initialization Basic OperationsIf you press the Exit button, the door will be opened Brown line with white stripes Wiegand Output SetupInitialization TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader mode setup Reader Mode Setup RF onlyNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyReader Mode Setup RF/PIN Combination Mode Enabling Keypad Input for the Card NumberButton To Register Cards in RF only Mode User managementRegistering Cards in a Combination of RF and P/W Modes To Register Cards in PIN Mode Registering Cards in RF Card / PIN Combination ModeMaster PIN To Delete a Registered Card or PIN Number Basic setup Duress AlarmTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorDefault is set to not used To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Buttons and press ENTTime setup To Specify the Output Time if the Card is AuthenticatedYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O Time Setup \ ` Advanced setting To Specify the TTL Output Operation ModeTo SET the Chime Bell Function To Specify the Input Mode for AUX To Specify the Chime Bell Operation Time36 고급 설정 To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorAdditional features To Specify the USE of the Tamper AlarmMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Press Button 3 and Button 6 in sequence and press ENT Other information Initial ValuesFunction Codes Sense if AUX 2 switches from L to H Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from H to LTroubleshooting TroubleshootingTroubleshooting √ RF OnlyEInstall and use the product as usual √ Enter the command to delete the user 14 + ENTService center Check the operation status of the productUser cards to the factory default Using the keypadUnregistered numbers in 5 consecutive times default CIf SSA-S2000 responds when you press the Exit buttonS2000 Irrelevant data is transferredDisconnection or short-circuit Consult with a qualified technicianProduct Specifications Product specificationsCorrect disposal of batteries in this product