Honeywell K14114 3/06 Rev.B setup guide Connecting AlarmNet 7845CV2

Page 10

LYNXR-I Installation and Setup Guide

LRR/IP Communications Device 24-Hour Standby Power

If you are installing the AlarmNet 7845GSM/7845i-GSM or 7845i-L you must install the Super High Capacity battery P/N!WALYNX-RCHB-SHA in the LYNXR-I.

The 7845i-ENT/7845i and 7845CV2 can not be used for installations requiring 24-hour standby.

AlarmNet 7845CV2

1.Connect the 4-wire communications cable to the LRR/IP communications port on the LYNXR-I.

2.Connect the four wires to the 7845CV2 as shown below:

4-WIRE CABLE (N4632-4)

BATTERY

ADEMCO

K4362

YEL

RED

BLK

GRN

RED

LRR/IP COMMUNICATIONS PORT

OUTDATA

NC

VDC+12

GND

DATAIN

BLK

YEL

GRN

LYNXR-I CONTROL PANEL

LYNX

STANDARD

CAPACITY

BATTERY

Connecting AlarmNet 7845CV2

P1 BAT

V+

GND

Z1/DATA IN

RAD FLT/ DATA OUT

TB1

7845CV2

07000-011-V2

Configuring Long Range Radio and Internet Communication Devices

1.Enable the communications device in programming field *55 and configure alarm reporting and module supervision in programming field *77.

2.Program the device as required using the 7720P programmer (refer to the Installation Instruction for the device that you are installing for additional information). Note that the device address must be set to 3.

1.When programming an AlarmNet 7845CV2 the radio’s “current limit” most option must be set to [Y] (yes).

2.The device must be registered before downloading or alarm reporting can take place.

- 10 -

Image 10

Contents Ademco LYNXR-I Recommendations for Smoke and Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents System Features Wall Mounting Mounting the ControlDesktop Mounting Wiring Overview Wiring ConnectionsLYNXR-I Wiring Connections Wiring Connections Full Line Seizure ConnectionsAlarmNet 7845i-L* Communications Device Connecting/Configuring Communication ModulesInstalling the 7845i-L Communications Module GeneralConnecting AlarmNet 7845GSM* / 7845i-GSM Connecting AlarmNet 7845i-ENT/7845iLRR/IP Communications Device 24-Hour Standby Power Connecting AlarmNet 7845CV2AlarmNet 7845CV2 AC Power and Rechargeable Backup Battery AC Power and Backup BatteryBackup battery Distance from TransformerAC Power and Rechargeable Backup Battery Replacing the Rechargeable BatteryGeneral Information Installing Wireless ZonesType Description Enter Installer code 4112 + # + Transmitter Battery LifeUsing the Transmitter Sniffer Mode Go/No Go Test ModeSetting DIP Switches on the 5800RL Transmitter Setting 5800RL DIP SwitchesGeneral Programming Information Entering Program ModeMechanics of Programming Programming a Data FieldInteractive Mode Used to Program Interactive Menu Mode Programming 56, 80, 81, 83, 84Loading Factory Defaults Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Defaults where applicable are Indicated in bold text Data Field DescriptionsDialer Programming Fields 43 Split/Dual Reporting Second Dialer Delay BurglaryEnable/Disable LRR/IP Communications Periodic Test ReportSystem Status and Restore Report Codes Programming 59 76 System Status Report CodesRestore Report Codes Dynamic Signaling Delay/ Dynamic Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldSignaling Priority = Aux key performs defined function Audio Alarm Verification AAV/RemoteAUX Function/1-Button Paging MacroZone Lists Menu Mode Enhanced Zone Programming ModeDevice Programming Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Report code Zone numberZone type Input typeLoop number or Loop and Serial Delete zone parameters confirmationSerial number Enroll modeVoice descriptor Descriptor Start by Event Device Programming Menu ModeProgramming Options Defined Start by Zone Type or System OperationUpon Restore of a Zone List Programming Powerline Carrier DevicesUpon a Zone Type or System Operation Device number Powerline Carrier DeviceProgramming Device actionZone List Menu Mode Enhanced Sequential Mode IA LC = copy the previous serial number entry from the bufferDelete serial number Assign Zone Voice Descriptors Assign zone voice descriptorsAssign Zone Voice Descriptor Voice Vocabulary IndexAssign custom voice descriptors Record Custom Voice DescriptorsCustom descriptor number Voice Prompt Programming Keypad Functions Voice Prompt ProgrammingDELETE/ Stay key Used to Toenroll Second Central Station Account NumberFront Basement Back Sliding Side Hall Gar ge Kitchen Patio Sensor Type Sensor Location Location ModifiersPendant Type Template selections Template To!Enter Expert Programming ModeTemplate Remote Programming Information Remote Programming/Control DownloadingEquipment required to download to a system at the premises Remote Programming Advisory Notes Security Codes System OperationPanic Keys Message Center Volume ControlKeypad Functions Other FunctionsSpeaker Phone Operation Remote Phone Control FeatureRemote Phone Control Feature Quick Arm NoteOperator Commands Audio Alarm Verification Two-Way Voice FeatureActivation Exit Error Alarm Displays Follow Me System Announcement FeaturePowerline Carrier Devices e.g. X10 devices Display MeaningAlarm System DisplaysArmed System Test Testing the SystemTest Mode Return to normal operationSystem Communication Communication OverviewCode Definition Report +1/4+1 Standard +1/4+1 ExpandedTrouble Conditions Troubleshooting GuideSystem Trouble Displays Symptom Possible Cause Remedy S t e m i n c l u d i n g W i r e l e s sN t r o l Smoke DetectorsProgramming Default Tables Boldface indicates defaults that differ between tablesDefault Duress Code Function Event loggingEvent Start StopDevice Number System OperationIndex House ID Serial Number Federal Communications Commission FCC Part 15 Statement Regulatory Agency StatementsUL Notice This is a Grade a residential system Federal Communications Commission FCC PartLimitations of this Alarm System LYNXR-I SpecificationsRead the Instructions ALL Output Circuits are Power Limited SystemLimited Warranty