Honeywell K14114 3/06 Rev.B setup guide Recommendations for Smoke and Heat Detectors

Page 2

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended.

For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.

In addition, we recommend the following:

Install a smoke detector inside every bedroom where a smoker sleeps.

Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed.

Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used.

Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE

SOUNDING OF FIRE NOTIFICATION APPLIANCES.

KITCHEN

 

 

KITCHEN

DINING

BEDROOM

 

BEDROOM

BEDROOM

DINING

TV ROOM

 

 

 

 

 

 

 

 

 

LIVING ROOM

BEDROOM

 

 

 

 

LIVING ROOM

BEDROOM

BEDROOM

 

 

 

 

 

 

 

 

 

 

Smoke Detectors for Minimum Protection

 

 

 

Smoke Detectors for Additional Protection

BEDROOM

 

 

Heat-Activated Detectors

 

 

BEDROOM BEDROOM

LIVING

KTCHN

GARAGE

ROOM

.

CLOSED

 

TO

 

 

DOOR

 

 

 

 

 

BEDROOM

 

BASEMENT

01000-002-V0

Recommendations For Proper Intrusion Protection

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This would include any skylights that may be present, and the upper windows in a multi-level building.

In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

-2 -

Image 2
Contents Ademco LYNXR-I Recommendations for Smoke and Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents System Features Desktop Mounting Mounting the ControlWall Mounting LYNXR-I Wiring Connections Wiring ConnectionsWiring Overview Wiring Connections Full Line Seizure ConnectionsAlarmNet 7845i-L* Communications Device Connecting/Configuring Communication ModulesInstalling the 7845i-L Communications Module GeneralConnecting AlarmNet 7845GSM* / 7845i-GSM Connecting AlarmNet 7845i-ENT/7845iAlarmNet 7845CV2 Connecting AlarmNet 7845CV2LRR/IP Communications Device 24-Hour Standby Power AC Power and Rechargeable Backup Battery AC Power and Backup BatteryBackup battery Distance from TransformerAC Power and Rechargeable Backup Battery Replacing the Rechargeable BatteryType Description Installing Wireless ZonesGeneral Information Enter Installer code 4112 + # + Transmitter Battery LifeUsing the Transmitter Sniffer Mode Go/No Go Test ModeSetting DIP Switches on the 5800RL Transmitter Setting 5800RL DIP SwitchesGeneral Programming Information Entering Program ModeMechanics of Programming Programming a Data FieldInteractive Mode Used to Program Interactive Menu Mode Programming 56, 80, 81, 83, 84Loading Factory Defaults Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Defaults where applicable are Indicated in bold text Data Field DescriptionsDialer Programming Fields 43 Split/Dual Reporting Second Dialer Delay BurglaryEnable/Disable LRR/IP Communications Periodic Test ReportSystem Status and Restore Report Codes Programming 59 76 System Status Report CodesRestore Report Codes Signaling Priority Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldDynamic Signaling Delay/ Dynamic = Aux key performs defined function Audio Alarm Verification AAV/RemoteAUX Function/1-Button Paging MacroZone Lists Menu Mode Enhanced Zone Programming ModeDevice Programming Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Report code Zone numberZone type Input typeLoop number or Loop and Serial Delete zone parameters confirmationVoice descriptor Enroll modeSerial number Descriptor Start by Event Device Programming Menu ModeProgramming Options Defined Start by Zone Type or System OperationUpon a Zone Type or System Operation Programming Powerline Carrier DevicesUpon Restore of a Zone List Device number Powerline Carrier DeviceProgramming Device actionZone List Menu Mode Enhanced Sequential Mode IA LC = copy the previous serial number entry from the bufferDelete serial number Assign Zone Voice Descriptors Assign zone voice descriptorsAssign Zone Voice Descriptor Voice Vocabulary IndexCustom descriptor number Record Custom Voice DescriptorsAssign custom voice descriptors DELETE/ Stay key Used to Voice Prompt ProgrammingVoice Prompt Programming Keypad Functions Toenroll Second Central Station Account NumberFront Basement Back Sliding Side Hall Gar ge Kitchen Patio Sensor Type Sensor Location Location ModifiersPendant Type Template To!Enter Expert Programming ModeTemplate selections Template Equipment required to download to a system at the premises Remote Programming/Control DownloadingRemote Programming Information Remote Programming Advisory Notes Panic Keys System OperationSecurity Codes Message Center Volume ControlKeypad Functions Other FunctionsSpeaker Phone Operation Remote Phone Control FeatureRemote Phone Control Feature Quick Arm NoteActivation Audio Alarm Verification Two-Way Voice FeatureOperator Commands Exit Error Alarm Displays Follow Me System Announcement FeaturePowerline Carrier Devices e.g. X10 devices Display MeaningAlarm System DisplaysArmed System Test Testing the SystemTest Mode Return to normal operationSystem Communication Communication OverviewCode Definition Report +1/4+1 Standard +1/4+1 ExpandedSystem Trouble Displays Troubleshooting GuideTrouble Conditions Symptom Possible Cause Remedy S t e m i n c l u d i n g W i r e l e s sN t r o l Smoke DetectorsProgramming Default Tables Boldface indicates defaults that differ between tablesDefault Duress Code Function Event loggingEvent Start StopDevice Number System OperationIndex House ID Serial Number Federal Communications Commission FCC Part 15 Statement Regulatory Agency StatementsUL Notice This is a Grade a residential system Federal Communications Commission FCC PartLimitations of this Alarm System Read the Instructions SpecificationsLYNXR-I ALL Output Circuits are Power Limited SystemLimited Warranty