Honeywell K14114 3/06 Rev.B setup guide Download Information 94, Enhanced Zone Programming Mode

Page 28

LYNXR-I Installation and Setup Guide

Data Field Descriptions

DOWNLOAD INFORMATION (94, 95)

94

Download Call Back Phone Number

This is the phone number the control will use to call back the downloading

Enter up to 20 digits as follows: 0–9, # +11 for “*”, #

computer.

 

Do not fill unused spaces. End field by pressing . To clear entries from

 

+ 12 for “#”, # + 13 for a pause.

 

field, press 94.

 

 

 

 

 

95

Ring Detection Count For Downloading/

Enter “15” to select defeat answering machine mode. If an

Remote Phone Control

answering machine is on the premises, you need to dial the

 

 

0 = disable station initiated download and remote

premises and hang up on the first ring. Wait at least five (5)

 

seconds (but no more than 22 seconds) and dial the premises

 

phone

 

phone number again. The control will pick up and announce

 

1-14 = number of rings before control picks up phone

 

“SYSTEM ENTER CODE” every three seconds.

 

line

 

15 = defeat answering machine

Note: To enter a number higher than 9 you must first press the [#] key.

 

 

 

OTHER PROGRAMMING COMMANDS

56 ENHANCED ZONE PROGRAMMING MODE

Interactive menu mode used for programming zone attributes and report codes. Refer to the 56 Enhanced Zone Programming Mode section for procedure.

80 DEVICE PROGRAMMING MENU MODE

Interactive menu mode for programming Powerline Carrier Devices. Refer to the 80 Device Programming Menu Mode section for detailed procedure.

81 ZONE LISTS MENU MODE

Interactive menu mode for programming zone lists for Powerline Carrier Devices. Refer to the 81 Zone List Menu Mode section for detailed procedure.

83 ENHANCED SEQUENTIAL MODE

Interactive menu mode used to enter RF transmitter serial numbers. Refer to the 83 Enhanced Sequential Mode section for detailed procedure.

84 ASSIGN ZONE VOICE DESCRIPTORS

Interactive menu mode used to assign descriptors to each zone. These descriptors will be announced whenever the system announces an event involving a zone.

85 RECORD CUSTOM VOICE DESCRIPTORS

Interactive menu mode used to record custom descriptors for use with each zone.

96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. NO. FOR

DOWNLOADING

Pressing 96 initializes the system for downloading.

97 SET ALL PROGRAM FIELDS TO 1 OF 4 SETS OF DEFAULT VALUES

See Default Tables at the end of this manual.

98 EXITS PROGRAMMING MODE

Prevents re-entry by: Installer Code + 8 + 0 + 0; allows re-entry only by Power-up, then [] and [#].

99 EXITS PROGRAMMING MODE

Allows re-entry to program mode by: Installer Code + 8 + 0 + 0; or by Power-up, then [] and [#].

- 28 -

Image 28
Contents Ademco LYNXR-I Recommendations for Smoke and Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents System Features Wall Mounting Mounting the ControlDesktop Mounting Wiring Overview Wiring ConnectionsLYNXR-I Wiring Connections Wiring Connections Full Line Seizure ConnectionsConnecting/Configuring Communication Modules Installing the 7845i-L Communications ModuleAlarmNet 7845i-L* Communications Device GeneralConnecting AlarmNet 7845GSM* / 7845i-GSM Connecting AlarmNet 7845i-ENT/7845iLRR/IP Communications Device 24-Hour Standby Power Connecting AlarmNet 7845CV2AlarmNet 7845CV2 AC Power and Backup Battery Backup batteryAC Power and Rechargeable Backup Battery Distance from TransformerAC Power and Rechargeable Backup Battery Replacing the Rechargeable BatteryGeneral Information Installing Wireless ZonesType Description Transmitter Battery Life Using the Transmitter Sniffer ModeEnter Installer code 4112 + # + Go/No Go Test ModeSetting DIP Switches on the 5800RL Transmitter Setting 5800RL DIP SwitchesEntering Program Mode Mechanics of ProgrammingGeneral Programming Information Programming a Data FieldInteractive Menu Mode Programming 56, 80, 81, 83, 84 Loading Factory DefaultsInteractive Mode Used to Program Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Defaults where applicable are Indicated in bold text Data Field DescriptionsDialer Programming Fields 43 Second Dialer Delay Burglary Enable/Disable LRR/IP CommunicationsSplit/Dual Reporting Periodic Test ReportSystem Status and Restore Report Codes Programming 59 76 System Status Report CodesRestore Report Codes Dynamic Signaling Delay/ Dynamic Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldSignaling Priority Audio Alarm Verification AAV/Remote AUX Function/1-Button Paging= Aux key performs defined function MacroEnhanced Zone Programming Mode Device Programming Menu ModeZone Lists Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Zone number Zone typeReport code Input typeLoop number or Loop and Serial Delete zone parameters confirmationSerial number Enroll modeVoice descriptor Descriptor Device Programming Menu Mode Programming Options DefinedStart by Event Start by Zone Type or System OperationUpon Restore of a Zone List Programming Powerline Carrier DevicesUpon a Zone Type or System Operation Powerline Carrier Device ProgrammingDevice number Device actionZone List Menu Mode Enhanced Sequential Mode IA LC = copy the previous serial number entry from the bufferDelete serial number Assign Zone Voice Descriptors Assign zone voice descriptorsAssign Zone Voice Descriptor Voice Vocabulary IndexAssign custom voice descriptors Record Custom Voice DescriptorsCustom descriptor number Voice Prompt Programming Keypad Functions Voice Prompt ProgrammingDELETE/ Stay key Used to Second Central Station Account Number Front Basement Back Sliding Side Hall Gar ge Kitchen PatioToenroll Sensor Type Sensor Location Location ModifiersPendant Type Template selections Template To!Enter Expert Programming ModeTemplate Remote Programming Information Remote Programming/Control DownloadingEquipment required to download to a system at the premises Remote Programming Advisory Notes Security Codes System OperationPanic Keys Volume Control Keypad FunctionsMessage Center Other FunctionsRemote Phone Control Feature Remote Phone Control FeatureSpeaker Phone Operation Quick Arm NoteOperator Commands Audio Alarm Verification Two-Way Voice FeatureActivation Follow Me System Announcement Feature Powerline Carrier Devices e.g. X10 devicesExit Error Alarm Displays Display MeaningAlarm System DisplaysTesting the System Test ModeArmed System Test Return to normal operationSystem Communication Communication OverviewCode Definition Report +1/4+1 Standard +1/4+1 ExpandedTrouble Conditions Troubleshooting GuideSystem Trouble Displays Symptom Possible Cause Remedy S t e m i n c l u d i n g W i r e l e s sN t r o l Smoke DetectorsProgramming Default Tables Boldface indicates defaults that differ between tablesDefault Duress Code Function Event loggingStart Stop Device NumberEvent System OperationIndex House ID Serial Number Regulatory Agency Statements UL Notice This is a Grade a residential systemFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC PartLimitations of this Alarm System LYNXR-I SpecificationsRead the Instructions ALL Output Circuits are Power Limited SystemLimited Warranty