Honeywell K14114 3/06 Rev.B Programming Powerline Carrier Devices, Upon Restore of a Zone List

Page 35

 

LYNXR-I Installation and Setup Guide

 

✻

 

80 Device Programming Menu Mode

STOP

The "STOP" programming determines when and under what conditions the device will be de-

 

activated. The following options are available:

Upon Restore of a Zone List

Restore Zone List: If a "ZONE LIST" is used as the “Stop” event, the device will de-activate when all the zones in that list restore from a previous fault, trouble, or alarm condition. This will occur regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" would normally only be used when a "ZONE LIST" is used to start the device.

Upon a Zone Type or System Operation

Zone Type/System Operation: Instead of using a "RESTORE ZONE LIST," a specific zone (response) type or system operation action can be selected to de-activate the device.

•If a specific "ZONE TYPE" is chosen, any zone of that response type that restores from a previous alarm, trouble, or fault condition will cause the device to de-activate.

•If a "SYSTEM OPERATION" is chosen, that operation will cause the device to de-activate.

During normal system operation, any devices may be manually started by keypad entry of: Code* + [#]

+4 + “n;” or manually stopped by keypad entry of: Code* + [#] + 7 + “n,” where “n” = the device number to be controlled.

*Code is required for devices 7 and 8. For devices 1-6, code is not required. See User Manual for more information.

Programming Powerline Carrier Devices

While in program mode, press ✻80 to enter Output Device Menu Mode. This mode is used to program all output devices used in the system. Refer to the output device table for ✻80 on the separate programming form when programming output devices.

Note: The House ID of the Powerline Carrier Devices must be entered in data field ✻25.

The prompts for ✻80 are as follows:

80

Powerline Carrier Device Programming Main Menu prompt

A 01

Device Number ---------

for entering the device number

b

Device Action ------------

for defining the action the device will perform when active

C

Start Event Type -------

for assigning the event type to start the action

d

Start Zone List ----------

for assigning the zone list to start the action

E

Start Zone Type---------

for assigning the zone type to start the action

F

Stop Zone List -----------

for assigning the zone list to stop the action

1A

Stop Zone Type----------

for assigning the zone type to stop the action

- 35 -

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Ademco LYNXR-I Recommendations For Proper Intrusion Protection Recommendations for Smoke and Heat DetectorsTable of Contents System Features Desktop Mounting Mounting the ControlWall Mounting LYNXR-I Wiring Connections Wiring ConnectionsWiring Overview Full Line Seizure Connections Wiring ConnectionsGeneral Connecting/Configuring Communication ModulesInstalling the 7845i-L Communications Module AlarmNet 7845i-L* Communications DeviceConnecting AlarmNet 7845i-ENT/7845i Connecting AlarmNet 7845GSM* / 7845i-GSMAlarmNet 7845CV2 Connecting AlarmNet 7845CV2LRR/IP Communications Device 24-Hour Standby Power Distance from Transformer AC Power and Backup BatteryBackup battery AC Power and Rechargeable Backup BatteryReplacing the Rechargeable Battery AC Power and Rechargeable Backup BatteryType Description Installing Wireless ZonesGeneral Information Go/No Go Test Mode Transmitter Battery LifeUsing the Transmitter Sniffer Mode Enter Installer code 4112 + # +Setting 5800RL DIP Switches Setting DIP Switches on the 5800RL TransmitterProgramming a Data Field Entering Program ModeMechanics of Programming General Programming InformationExiting Program Mode Interactive Menu Mode Programming 56, 80, 81, 83, 84Loading Factory Defaults Interactive Mode Used to ProgramZone Response Type Definitions 5806/5807/5808 Data Field Descriptions Defaults where applicable are Indicated in bold textDialer Programming Fields 43 Periodic Test Report Second Dialer Delay BurglaryEnable/Disable LRR/IP Communications Split/Dual ReportingSystem Status Report Codes System Status and Restore Report Codes Programming 59 76Restore Report Codes Signaling Priority Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldDynamic Signaling Delay/ Dynamic Macro Audio Alarm Verification AAV/RemoteAUX Function/1-Button Paging = Aux key performs defined functionEnhanced Sequential Mode Enhanced Zone Programming ModeDevice Programming Menu Mode Zone Lists Menu ModeEnhanced Zone Programming Mode Input type Zone numberZone type Report codeDelete zone parameters confirmation Loop number or Loop and SerialVoice descriptor Enroll modeSerial number Descriptor Start by Zone Type or System Operation Device Programming Menu ModeProgramming Options Defined Start by EventUpon a Zone Type or System Operation Programming Powerline Carrier DevicesUpon Restore of a Zone List Device action Powerline Carrier DeviceProgramming Device numberZone List Menu Mode Enhanced Sequential Mode = copy the previous serial number entry from the buffer IA LCDelete serial number Assign zone voice descriptors Assign Zone Voice DescriptorsVoice Vocabulary Index Assign Zone Voice DescriptorCustom descriptor number Record Custom Voice DescriptorsAssign custom voice descriptors DELETE/ Stay key Used to Voice Prompt ProgrammingVoice Prompt Programming Keypad Functions Sensor Type Sensor Location Location Modifiers Second Central Station Account NumberFront Basement Back Sliding Side Hall Gar ge Kitchen Patio ToenrollPendant Type Template To!Enter Expert Programming ModeTemplate selections Template Equipment required to download to a system at the premises Remote Programming/Control DownloadingRemote Programming Information Remote Programming Advisory Notes Panic Keys System OperationSecurity Codes Other Functions Volume ControlKeypad Functions Message CenterQuick Arm Note Remote Phone Control FeatureRemote Phone Control Feature Speaker Phone OperationActivation Audio Alarm Verification Two-Way Voice FeatureOperator Commands Display Meaning Follow Me System Announcement FeaturePowerline Carrier Devices e.g. X10 devices Exit Error Alarm DisplaysSystem Displays AlarmReturn to normal operation Testing the SystemTest Mode Armed System TestCommunication Overview System CommunicationReport +1/4+1 Standard +1/4+1 Expanded Code DefinitionSystem Trouble Displays Troubleshooting GuideTrouble Conditions S t e m i n c l u d i n g W i r e l e s s Symptom Possible Cause RemedySmoke Detectors N t r o lBoldface indicates defaults that differ between tables Programming Default TablesFunction Event logging Default Duress CodeSystem Operation Start StopDevice Number EventIndex House ID Serial Number Federal Communications Commission FCC Part Regulatory Agency StatementsUL Notice This is a Grade a residential system Federal Communications Commission FCC Part 15 StatementLimitations of this Alarm System Read the Instructions SpecificationsLYNXR-I System ALL Output Circuits are Power LimitedLimited Warranty
Top Page Image Contents