Honeywell K14114 3/06 Rev.B setup guide Connecting/Configuring Communication Modules, General

Page 8

LYNXR-I Installation and Setup Guide

Connecting/Configuring Communication Modules

General

This LYNXR-I supports central station reporting via long range radio and internet. It also supports upload/download programming capability via the Internet or a Private local area network (Intranet). This allows site maintenance independent of central station monitoring, and modification to sites globally via the Internet or through a private LAN. Refer to the instructions provided with the LRR/IP Communications Device being installed for additional information regarding its installation, programming, and registration. Zone 103 is the supervisory zone for the Communications Device.

LYNXR-I does not support the 7845i-ENT remote access feature.

Connecting Long Range Radio and Internet Communication Devices

Connect and configure the communications device as follows (refer to the Installation Instructions for device that you are installing for additional information):

The wire run between the LYNXR-I and the Communications Device must not exceed ten (10) feet.

UL The 7845ENT and 7845CV2 have been evaluated by UL for Household Burglary installations. The communications modules have not been evaluated for Household Fire installations.

AlarmNet 7845i-L* Communications Device

1.Install the module into the LYNXR-I back plate and secure it with the two provided screws. Refer to the diagrams below.

2.Connect the provided ribbon cable between the module and the PC board. This cable provides DC power and ground for the module and data in/data out connections.

3.Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet connection.

* When available. The 7845i-L module has not been evaluated by UL.

CABLE	7720P PROGRAMMER	RJ45 (FOR INTERNET	COMMUNICATIONS
	CONNECTION	CONNECTION)	PORT FOR
			INTERNAL 7845i-L
			MODULE ONLY

LRR / IP PORT

07000-004-V0

Installing the 7845i-L Communications Module

- 8 -

Image 8

Contents Ademco LYNXR-I Recommendations for Smoke and Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents System Features Desktop Mounting Mounting the ControlWall Mounting LYNXR-I Wiring Connections Wiring ConnectionsWiring Overview Wiring Connections Full Line Seizure ConnectionsConnecting/Configuring Communication Modules Installing the 7845i-L Communications ModuleAlarmNet 7845i-L* Communications Device GeneralConnecting AlarmNet 7845GSM* / 7845i-GSM Connecting AlarmNet 7845i-ENT/7845iAlarmNet 7845CV2 Connecting AlarmNet 7845CV2LRR/IP Communications Device 24-Hour Standby Power AC Power and Backup Battery Backup batteryAC Power and Rechargeable Backup Battery Distance from TransformerAC Power and Rechargeable Backup Battery Replacing the Rechargeable BatteryType Description Installing Wireless ZonesGeneral Information Transmitter Battery Life Using the Transmitter Sniffer ModeEnter Installer code 4112 + # + Go/No Go Test ModeSetting DIP Switches on the 5800RL Transmitter Setting 5800RL DIP SwitchesEntering Program Mode Mechanics of ProgrammingGeneral Programming Information Programming a Data FieldInteractive Menu Mode Programming 56, 80, 81, 83, 84 Loading Factory DefaultsInteractive Mode Used to Program Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Defaults where applicable are Indicated in bold text Data Field DescriptionsDialer Programming Fields 43 Second Dialer Delay Burglary Enable/Disable LRR/IP CommunicationsSplit/Dual Reporting Periodic Test ReportSystem Status and Restore Report Codes Programming 59 76 System Status Report CodesRestore Report Codes Signaling Priority Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldDynamic Signaling Delay/ Dynamic Audio Alarm Verification AAV/Remote AUX Function/1-Button Paging= Aux key performs defined function MacroEnhanced Zone Programming Mode Device Programming Menu ModeZone Lists Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Zone number Zone typeReport code Input typeLoop number or Loop and Serial Delete zone parameters confirmationVoice descriptor Enroll modeSerial number Descriptor Device Programming Menu Mode Programming Options DefinedStart by Event Start by Zone Type or System OperationUpon a Zone Type or System Operation Programming Powerline Carrier DevicesUpon Restore of a Zone List Powerline Carrier Device ProgrammingDevice number Device actionZone List Menu Mode Enhanced Sequential Mode IA LC = copy the previous serial number entry from the bufferDelete serial number Assign Zone Voice Descriptors Assign zone voice descriptorsAssign Zone Voice Descriptor Voice Vocabulary IndexCustom descriptor number Record Custom Voice DescriptorsAssign custom voice descriptors DELETE/ Stay key Used to Voice Prompt ProgrammingVoice Prompt Programming Keypad Functions Second Central Station Account Number Front Basement Back Sliding Side Hall Gar ge Kitchen PatioToenroll Sensor Type Sensor Location Location ModifiersPendant Type Template To!Enter Expert Programming ModeTemplate selections Template Equipment required to download to a system at the premises Remote Programming/Control DownloadingRemote Programming Information Remote Programming Advisory Notes Panic Keys System OperationSecurity Codes Volume Control Keypad FunctionsMessage Center Other FunctionsRemote Phone Control Feature Remote Phone Control FeatureSpeaker Phone Operation Quick Arm NoteActivation Audio Alarm Verification Two-Way Voice FeatureOperator Commands Follow Me System Announcement Feature Powerline Carrier Devices e.g. X10 devicesExit Error Alarm Displays Display MeaningAlarm System DisplaysTesting the System Test ModeArmed System Test Return to normal operationSystem Communication Communication OverviewCode Definition Report +1/4+1 Standard +1/4+1 ExpandedSystem Trouble Displays Troubleshooting GuideTrouble Conditions Symptom Possible Cause Remedy S t e m i n c l u d i n g W i r e l e s sN t r o l Smoke DetectorsProgramming Default Tables Boldface indicates defaults that differ between tablesDefault Duress Code Function Event loggingStart Stop Device NumberEvent System OperationIndex House ID Serial Number Regulatory Agency Statements UL Notice This is a Grade a residential systemFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC PartLimitations of this Alarm System Read the Instructions SpecificationsLYNXR-I ALL Output Circuits are Power Limited SystemLimited Warranty