Honeywell K14114 3/06 Rev.B setup guide AC Power and Rechargeable Backup Battery

Page 12

LYNXR-I Installation and Setup Guide

AC Power and Rechargeable Backup Battery

The LYNXR-I is equipped with an integral, replaceable, rechargeable battery pack rated at 7.7Vdc. Select the appropriate battery pack, based on the installation’s requirement, and install the battery pack.

Model/Part Number	Battery StandbyTime	Low Battery Notification
LYNXRCHKIT-SC	4-hours (minimum)	Approximately 1-hour before battery depletion

LYNXRCHKIT-HC	24-hours (minimum)	At least 1-hour before battery depletion

LYNXRCHKIT-SHA	24-hours (minimum)	At least 1-hour before battery depletion

Replacing the Rechargeable Battery

1.When battery replacement is required, unplug the transformer from the wall outlet, and open the control panel cover.

2.Remove the battery retainer and disconnect the battery pack connector from the receptacle on the terminal block PC board.

3.Remove the battery pack from the back plate.

4.If required, replace the tape that secures the battery pack.

5.Install a replacement battery pack (P/N LYNXRCHKIT-SC, LYNXRCHKIT-HC or LYNXRCHKIT-SHA) into the back plate.

6.Install the battery retainer.

7.Connect the battery connector to the receptacle on the terminal block PC board.

8.After the wiring connection has been made, snap the front assembly to the back plate.

9.Plug the transformer into a 24-hour, 110VAC unswitched outlet.

10.Rechargeable batteries may take up to 48- hours to fully charge. The “LOW BAT” message should clear within four hours or by entering Test Mode.

LYNXRCHKIT-HC OR LYNXRCHKIT-SC

RETAINER

BATTERY

PACK

TAPE

BATTERY CONNECTOR

BATTERY

RECEPTACLE

LYNXRCHKIT-SHA

RETAINER

BATTERY

PACK

	BATTERY	TAPE
	CONNECTOR	TAPE
	CONNECTOR

BATTERY

RECEPTACLE

07000-006-V1

Ensure the control panel assembly is snapped closed prior to applying AC power.

- 12 -

Image 12

Contents Ademco LYNXR-I Recommendations for Smoke and Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents System Features Mounting the Control Wall MountingDesktop Mounting Wiring Connections Wiring OverviewLYNXR-I Wiring Connections Wiring Connections Full Line Seizure ConnectionsConnecting/Configuring Communication Modules Installing the 7845i-L Communications ModuleAlarmNet 7845i-L* Communications Device GeneralConnecting AlarmNet 7845GSM* / 7845i-GSM Connecting AlarmNet 7845i-ENT/7845iConnecting AlarmNet 7845CV2 LRR/IP Communications Device 24-Hour Standby PowerAlarmNet 7845CV2 AC Power and Backup Battery Backup batteryAC Power and Rechargeable Backup Battery Distance from TransformerAC Power and Rechargeable Backup Battery Replacing the Rechargeable BatteryInstalling Wireless Zones General InformationType Description Transmitter Battery Life Using the Transmitter Sniffer ModeEnter Installer code 4112 + # + Go/No Go Test ModeSetting DIP Switches on the 5800RL Transmitter Setting 5800RL DIP SwitchesEntering Program Mode Mechanics of ProgrammingGeneral Programming Information Programming a Data FieldInteractive Menu Mode Programming 56, 80, 81, 83, 84 Loading Factory DefaultsInteractive Mode Used to Program Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Defaults where applicable are Indicated in bold text Data Field DescriptionsDialer Programming Fields 43 Second Dialer Delay Burglary Enable/Disable LRR/IP CommunicationsSplit/Dual Reporting Periodic Test ReportSystem Status and Restore Report Codes Programming 59 76 System Status Report CodesRestore Report Codes Dynamic Signaling DELAY/DYNAMIC Signaling Priority Field Dynamic Signaling Delay/ DynamicSignaling Priority Audio Alarm Verification AAV/Remote AUX Function/1-Button Paging= Aux key performs defined function MacroEnhanced Zone Programming Mode Device Programming Menu ModeZone Lists Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Zone number Zone typeReport code Input typeLoop number or Loop and Serial Delete zone parameters confirmationEnroll mode Serial numberVoice descriptor Descriptor Device Programming Menu Mode Programming Options DefinedStart by Event Start by Zone Type or System OperationProgramming Powerline Carrier Devices Upon Restore of a Zone ListUpon a Zone Type or System Operation Powerline Carrier Device ProgrammingDevice number Device actionZone List Menu Mode Enhanced Sequential Mode IA LC = copy the previous serial number entry from the bufferDelete serial number Assign Zone Voice Descriptors Assign zone voice descriptorsAssign Zone Voice Descriptor Voice Vocabulary IndexRecord Custom Voice Descriptors Assign custom voice descriptorsCustom descriptor number Voice Prompt Programming Voice Prompt Programming Keypad FunctionsDELETE/ Stay key Used to Second Central Station Account Number Front Basement Back Sliding Side Hall Gar ge Kitchen PatioToenroll Sensor Type Sensor Location Location ModifiersPendant Type To!Enter Expert Programming Mode Template selections TemplateTemplate Remote Programming/Control Downloading Remote Programming InformationEquipment required to download to a system at the premises Remote Programming Advisory Notes System Operation Security CodesPanic Keys Volume Control Keypad FunctionsMessage Center Other FunctionsRemote Phone Control Feature Remote Phone Control FeatureSpeaker Phone Operation Quick Arm NoteAudio Alarm Verification Two-Way Voice Feature Operator CommandsActivation Follow Me System Announcement Feature Powerline Carrier Devices e.g. X10 devicesExit Error Alarm Displays Display MeaningAlarm System DisplaysTesting the System Test ModeArmed System Test Return to normal operationSystem Communication Communication OverviewCode Definition Report +1/4+1 Standard +1/4+1 ExpandedTroubleshooting Guide Trouble ConditionsSystem Trouble Displays Symptom Possible Cause Remedy S t e m i n c l u d i n g W i r e l e s sN t r o l Smoke DetectorsProgramming Default Tables Boldface indicates defaults that differ between tablesDefault Duress Code Function Event loggingStart Stop Device NumberEvent System OperationIndex House ID Serial Number Regulatory Agency Statements UL Notice This is a Grade a residential systemFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC PartLimitations of this Alarm System Specifications LYNXR-IRead the Instructions ALL Output Circuits are Power Limited SystemLimited Warranty