| 56 Enhanced Zone Programming Mode | ||||||
✻ |
|
|
|
|
|
| |
|
|
|
|
| Enroll mode | If “L” is displayed, the serial number for this transmitter has already | |
| IA | LC |
| 0 = advance to the VOICE DESCRIPTOR | been entered. It may, however, still be viewed, confirmed (only if in | ||
|
| listen mode), or deleted. | |||||
|
| prompt (1C). | |||||
|
|
|
| ||||
|
|
|
|
| Note: This will save all zone parameters. | View serial number | |
|
|
|
|
| 1 = enter now and proceed to SERIAL | ||
|
|
|
|
| Enter “3”. Each digit will be redisplayed, and the keypad will beep once | ||
|
|
|
|
| NUMBER prompt (1b). | for digits | |
|
|
|
|
| Note: Not applicable if the serial number is already |
|
|
|
|
|
|
| present. | Confirm serial number | |
|
|
|
|
| 2 = copy the last serial number entered into | The serial number/loop number combination can be confirmed after one | |
|
|
|
|
| transmission from a BR type device or two transmissions (fault and | ||
|
|
|
|
| local ram. | ||
|
|
|
|
| restore) from a UR or RF type device. If a transmission is received that | ||
|
|
|
|
| Note: If this is the 1st zone, none will be in the buffer | ||
|
|
|
|
| matches the serial number and loop number entered, the system will | ||
|
|
|
|
| and the panel will emit a long tone. Not valid if | confirm the reception by announcing the Voice Descriptor for the zone, | |
|
|
|
|
| serial number is already present. | if it is programmed, followed by three beeps, and a “C” will appear on | |
|
|
|
|
| 3 = view existing serial number. | the display indicating the received serial number and loop number | |
|
|
|
|
| Note: Only if “L” is displayed. If “L” is not displayed, | have been confirmed. No further transmissions will be received. | |
|
|
|
|
| panel will emit a long beep. | Delete serial number | |
|
|
|
|
| 9 = advance to F; delete existing serial | ||
|
|
|
|
| The serial number can be deleted by entering “9”. | ||
|
|
|
|
| number. | ||
|
|
|
|
|
|
| |
|
|
|
|
| Note: Only if “L” is displayed. If “L” is not displayed, | If “L” is not displayed, the serial number for this transmitter has not | |
|
|
|
|
| panel will emit a long beep. | ||
|
|
|
|
| been previously entered. You may enter the serial number manually, | ||
|
|
|
|
| [✻] = advance to the VOICE DESCRIPTOR | ||
|
|
|
|
| copy the previous serial number, return to Prompt (E) or enter the | ||
|
|
|
|
| prompt (1C). This will save all zone | serial number later using the ✻83 Enhanced Sequential Mode. | |
|
|
|
|
| parameters. | Manual entry | |
|
|
|
|
| [#] = return to the LOOP NUMBER prompt (E). | ||
|
|
|
|
| Enter "1" to advance to Serial number prompt (1b). | ||
|
|
|
|
| Note: In order for all entered parameters to be | ||
|
|
|
|
| Copy the previous serial number | ||
|
|
|
|
| accepted, you must advance to the VOICE | Enter “2” to copy the previous serial number entered. | |
|
|
|
|
| DESCRIPTOR prompt (1C). | Return to Prompt (E) | |
|
|
|
|
|
| Enter “#” to return to Loop Number prompt (E). | |
|
|
|
|
|
| Enter transmitter later | |
|
|
|
|
|
| Enter “0” or “✻” if you wish to enter the transmitter later, using the | |
|
|
|
|
|
| ✻83 Enhanced Sequential Mode described later in this manual. | |
|
|
|
|
|
| Notes: (1) The panel will listen only when it is in the idle loop waiting | |
|
|
|
|
|
| for key entry and a serial number has been entered. If a key | |
|
|
|
|
|
| is entered, the function must be completed and the panel | |
|
|
|
|
|
| will listen again. | |
|
|
|
|
|
| (2) A long beep indicates illegal entry or duplicate serial number/loop | |
|
|
|
|
|
| entry | |
|
|
|
|
| Serial number | In this mode, the transmitter serial numbers can only be entered | |
| Ib |
|
|
| Enter the transmitter’s | manually. |
|
|
|
|
|
|
| ||
|
|
|
| [#] = return to prompt 1A and reject any serial | Enter the | ||
|
|
|
|
| numbers entries that have been made. | ||
|
|
|
|
| incorrect digit is entered, press the [#] key to backup to prompt (1A) | ||
|
|
|
|
| [✻] = return to prompt 1A, (if a valid serial | ||
|
|
|
|
| and start over. When all 7 digits are entered, press the [✻] key. | ||
|
|
|
|
| number has been entered, the "L" is |
|
|
|
|
|
|
| displayed and the serial number will be | If 52 seconds passes and no entry has been made, the system returns | |
|
|
|
|
| copied into EEROM from the last serial | to prompt (1A). | |
|
|
|
|
| entered into the buffer.) | Notes: (1) If the serial and loop number combination is already | |
|
|
|
|
| Note: This prompt can be used only to manually | ||
|
|
|
|
|
| present the keypad will emit a single long beep and the | |
|
|
|
|
| enroll a serial number. RF enrollment will be |
| system will return to the (1A) prompt and “L” will be |
|
|
|
|
| rejected and the current zone descriptor will be |
| displayed. |
|
|
|
|
| announced, followed by a single long beep | (2) | If less than 7 digits have been entered, the keypad will |
|
|
|
|
| and the system will return to prompt (1A). |
| emit a single long beep and return to the (1A) prompt |
|
|
|
|
|
|
| without displaying the “L”. |
|
|
|
|
|
| (3) | If more than 7 digits have been entered, the first 6 digits |
|
|
|
|
|
|
| will be saved along with the last digit that was entered |
|
|
|
|
|
|
| (entering 123456789 yields the serial number 1234569). |
|
|
|
|
|
|
| |
|
|
|
|
| Voice descriptor | Each zone can have a voice descriptor of up to 3 words that will be | |
| IC |
|
|
| 0 = skip to next zone (A) | announced whenever the system announces status for that zone. | |
|
|
|
|
|
| ||
|
|
|
| 1 = enter descriptor mode; existing descriptor |
|
| |
|
|
|
|
| for this zone will be announced |
|
|
|
|
|
|
|
|
|
|
- 32 -