Honeywell K14114 3/06 Rev.B setup guide Interactive Menu Mode Programming 56, 80, 81, 83, 84

Page 17

LYNXR-I Installation and Setup Guide

Interactive Menu Mode Programming (✻56, ✻80, ✻81, ✻83, ✻84, ✻85)

Press [✻] + interactive mode No. (i.e., ✻56). The keypad will display the first of a series of prompts. A detailed procedure (with displays of prompts) is provided in later sections of this manual.

 

Interactive Mode

Used to Program

✻56 Enhanced Zone Programming Mode

Zone characteristics, report codes, and serial numbers

✻80 Device Programming Menu Mode

Powerline Carrier Devices

✻81

Zone List Menu Mode

Zone Lists for powerline carrier activation

✻83

Enhanced Sequential Mode

5800 Series transmitter serial numbers

✻84

Assign Zone Voice Descriptors

Voice descriptors for each zone

✻85

Record Custom Voice Descriptors

Up to 5 custom voice descriptors for zones

Loading Factory Defaults

To load the factory defaults, enter the Programming mode, press ✻97, then press number 1, 2, 3, or 4 to select from default tables 1-4 at the back of this manual, or press “0” if you are not selecting a default table.

If a default table is loaded, any data that has already been programmed into the system will be changed according to the default table selected!

✻96 resets all subscriber account numbers and CSID in preparation for an initial download.

Exiting Program Mode

✻98 inhibits re-entry into the Expert or Voice Prompt Programming modes using the Installer Code.

✻99 allows re-entry into the Expert Program mode using Installer Code (4112) + 800 or into the Voice

Prompt Programming mode using Installer Code (4112) + 888.

Note: After exiting program mode (or upon power-up), the system takes up to a minute to reset. To bypass the reset delay, press [#] + [0].

Pass-Thru Programming

This mode allows the Installer to use the LYNXR-I keypad and display to program the communications device that is connected to the LYNXR-I. Refer to the communications device’s installation instruction to determine whether this feature is supported.

Entering Pass-Thru Programming mode

1.After power-up, enter the Installer Code (4112) + 899.

2.Once you have entered Pass-Thru Programming mode “PtP” will be displayed on the keypad.

3.Refer to the Installation Instructions for the LRR/IP Communications Device being installed for additional programming information.

LYNXR-I will abort this mode:

•When it receives an abort command from the new communications device.

•If it fails to communicate with an communications device after 20 attempts.

•30 minutes after the last key has been pressed.

- 17 -

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Ademco LYNXR-I Recommendations For Proper Intrusion Protection Recommendations for Smoke and Heat DetectorsTable of Contents System Features Desktop Mounting Mounting the ControlWall Mounting LYNXR-I Wiring Connections Wiring ConnectionsWiring Overview Full Line Seizure Connections Wiring ConnectionsInstalling the 7845i-L Communications Module Connecting/Configuring Communication ModulesAlarmNet 7845i-L* Communications Device GeneralConnecting AlarmNet 7845i-ENT/7845i Connecting AlarmNet 7845GSM* / 7845i-GSMAlarmNet 7845CV2 Connecting AlarmNet 7845CV2LRR/IP Communications Device 24-Hour Standby Power Backup battery AC Power and Backup BatteryAC Power and Rechargeable Backup Battery Distance from TransformerReplacing the Rechargeable Battery AC Power and Rechargeable Backup BatteryType Description Installing Wireless ZonesGeneral Information Using the Transmitter Sniffer Mode Transmitter Battery LifeEnter Installer code 4112 + # + Go/No Go Test ModeSetting 5800RL DIP Switches Setting DIP Switches on the 5800RL TransmitterMechanics of Programming Entering Program ModeGeneral Programming Information Programming a Data FieldLoading Factory Defaults Interactive Menu Mode Programming 56, 80, 81, 83, 84Interactive Mode Used to Program Exiting Program ModeZone Response Type Definitions 5806/5807/5808 Data Field Descriptions Defaults where applicable are Indicated in bold textDialer Programming Fields 43 Enable/Disable LRR/IP Communications Second Dialer Delay BurglarySplit/Dual Reporting Periodic Test ReportSystem Status Report Codes System Status and Restore Report Codes Programming 59 76Restore Report Codes Signaling Priority Dynamic Signaling DELAY/DYNAMIC Signaling Priority FieldDynamic Signaling Delay/ Dynamic AUX Function/1-Button Paging Audio Alarm Verification AAV/Remote= Aux key performs defined function MacroDevice Programming Menu Mode Enhanced Zone Programming ModeZone Lists Menu Mode Enhanced Sequential ModeEnhanced Zone Programming Mode Zone type Zone numberReport code Input typeDelete zone parameters confirmation Loop number or Loop and SerialVoice descriptor Enroll modeSerial number Descriptor Programming Options Defined Device Programming Menu ModeStart by Event Start by Zone Type or System OperationUpon a Zone Type or System Operation Programming Powerline Carrier DevicesUpon Restore of a Zone List Programming Powerline Carrier DeviceDevice number Device actionZone List Menu Mode Enhanced Sequential Mode = copy the previous serial number entry from the buffer IA LCDelete serial number Assign zone voice descriptors Assign Zone Voice DescriptorsVoice Vocabulary Index Assign Zone Voice DescriptorCustom descriptor number Record Custom Voice DescriptorsAssign custom voice descriptors DELETE/ Stay key Used to Voice Prompt ProgrammingVoice Prompt Programming Keypad Functions Front Basement Back Sliding Side Hall Gar ge Kitchen Patio Second Central Station Account NumberToenroll Sensor Type Sensor Location Location ModifiersPendant Type Template To!Enter Expert Programming ModeTemplate selections Template Equipment required to download to a system at the premises Remote Programming/Control DownloadingRemote Programming Information Remote Programming Advisory Notes Panic Keys System OperationSecurity Codes Keypad Functions Volume ControlMessage Center Other FunctionsRemote Phone Control Feature Remote Phone Control FeatureSpeaker Phone Operation Quick Arm NoteActivation Audio Alarm Verification Two-Way Voice FeatureOperator Commands Powerline Carrier Devices e.g. X10 devices Follow Me System Announcement FeatureExit Error Alarm Displays Display MeaningSystem Displays AlarmTest Mode Testing the SystemArmed System Test Return to normal operationCommunication Overview System CommunicationReport +1/4+1 Standard +1/4+1 Expanded Code DefinitionSystem Trouble Displays Troubleshooting GuideTrouble Conditions S t e m i n c l u d i n g W i r e l e s s Symptom Possible Cause RemedySmoke Detectors N t r o lBoldface indicates defaults that differ between tables Programming Default TablesFunction Event logging Default Duress CodeDevice Number Start StopEvent System OperationIndex House ID Serial Number UL Notice This is a Grade a residential system Regulatory Agency StatementsFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC PartLimitations of this Alarm System Read the Instructions SpecificationsLYNXR-I System ALL Output Circuits are Power LimitedLimited Warranty
Top Page Image Contents