AMX MET-ECOM-D manual Verifying and Upgrading the device firmware via an IP

Page 69

Programming

List of previously saved IP Addresses

FIG. 45 Assigning Communication Settings and TCP/IP Settings

10.Click OK three times to close the open dialogs and save your settings.

11.Click Yes to interrupt the current communication from the Master and apply the new settings.

12.Select Tools > Reboot the Master Controller to access the Reboot the Master dialog, then click Reboot to reboot the Master and incorporate any changes.

13.Once the dialog replies with "Reboot of system complete", press Done.

14.Click the OnLine Tree tab in the Workspace window to view the devices on the System. The default System value is one.

15.Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the list.

Verifying and Upgrading the device firmware via an IP

1.Click the OnLine Tree tab in the Workspace window to view the devices on the System. The default System value is one.

2.Right-click the associated System number (from the Workspace window) and select Refresh System to detect all devices on the current system, establish a new connection to the Master, and refresh the System list with devices on that system.

3.After the Communication Verification dialog window verifies active communication between the PC and the Master, verify the Metreau Entry Communicator appears in the OnLine Tree tab of the Workspace window. The default device value is 10001.

4.If the device firmware version is not the latest available; locate and download the latest firmware file from the www.amx.com > Tech Center > Downloadable Files > Firmware Files section of the website.

5.Select Tools > Firmware Transfers > Send to NetLinx Device from the Main menu to open the Send to NetLinx Device dialog (FIG. 46). Verify the device’s System and Device number values match those values listed within the System folder in the OnLine Tree tab of the Workspace window.

Metreau Entry Communicators	63

Image 69

Contents Metreau Entry Communicators AMX Limited Warranty and Disclaimer Table of Contents Using Zero Configuration Programming Creating Popup Pages Overview Metreau Entry CommunicatorsMetreau Entry Communicators Front Components Front ComponentsProduct Specifications MET-ECOM MET-ECOM SpecificationsRear Components Dimensions MET-ECOM-D Specifications Product Specifications MET-ECOM-DMET-ECOM-D Specifications Positioning the Camera Camera Viewing Angle AdjustmentDefault Rear Panel Connectors Wiring and ConnectionsPoE Power Over Ethernet Ethernet 10/100 Base-T RJ-45 Wiring ConfigurationEthernet Pinouts and Signals Connections PairingRelay Port Connections and Wiring Input/Output I/O Port Connections and WiringConnecting The Device via I/O Port Wiring SpecificationsInstalling the CAT5 Suppression Ferrite Ferrite Installation RequiredSystem Diagram Intercom System DiagramWiring and Connections Metreau Entry Communicators Mounting and Installation MET-ECOM / MET-ECOM-D Installation OverviewDimensions Front View Mounting SpecificationsTop View Side ViewsTypical Installation Without Expansion Clips Typical Installation Without Expansion ClipsDevice and wall box must have an Earth ground Installing the Wall Box Without the Use of Tabs Recommended Cutout For Wall Box Wall Surface Installation Using Expansion ClipsReplacement drywall clip sets must be ordered from AMX Flat Surface Installation Points Installing Into a Flat Surface Using Mounting ScrewsRemoving the Device From the Wall Included in the Kit Using the Optional Surface Mount BoxProvides mounting specifications for the CB-MET-ECOMS Surface Mount Box SpecificationsInstalling the Metreau Entry Communicator Ferrite Installation RequiredMounting and Installation Using Zero Configuration Bonjour Zero-Configuration ClientConnecting In a Network With a Dhcp Server This case the serial number is 218001WHP2980023 Connecting In a Network Without a Dhcp ServerInternet Properties TCP/IP Properties dialog Using Zero Configuration Metreau Entry Communicators Configuration Manager Summary of Settings Page initial view Using the Configuration ManagerAccessing the Configuration Manager Command ButtonsSummary of Device Settings Summary of Device SettingsDevice Information IP Settings Rebooting the DeviceNetLinx Settings Checking the Firmware VersionConfiguration Page Network IP Settings Tab ConfigurationSetting the IP Address Setting the DNS AddressConfiguration Page Network IP Settings Tab Configuration Page NetLinx Settings Tab Setting the Icsp Connection to the NetLinx MasterConfiguration Page NetLinx Settings Tab Configuration Page User Settings Tab Setting a New Username and PasswordConfiguration Page User Settings Tab Device Utilities Device UtilitiesUtility Meta Information Image File Requirements Creating Display ImagesFile Upload ImagesSave the file as a .BMP image FIG TPDesign4 Resource Manager Creating Dynamic ImagesCreate Dynamic Image dialog Creating a New Dynamic ImageDeleting a Display Image From the Device Uploading a Display Image To The DeviceSetting Device Audio Audio/Video Page Audio Settings TabAudio/Video Page Audio Settings Tab Audio/VideoAudio/Video Page Video Settings Tab Audio/Video Page Video Settings TabCamera/Video Stream Configuration Video CodecAudio/Video Page Display Settings Tab Setting Device VideoAudio/Video Page Display Settings Tab Setting the Display Settings On The DeviceTouch Panel Intercom Commands SENDCOMMANDsTouch Panel Intercom Commands ProgrammingSTREAM-PLAY STREAM-GETSTREAM-STOP MOD?RTP, Rtcp Video and Audio Streaming Commands RTP, Rtcp Video and Audio Streaming CommandsSET Volume GET VolumeSET Audio GET GainFace Plate LED Commands Face Plate LED CommandsCamera Commands Camera CommandsGET CAM-CST SET CAM-CSTSET CAM-SAT GET CAM-SATLCD Commands LCD CommandsGET CAM-FLICK SET DISP-BANNERGET DISP-BRT SET DISP-BRTSET DISP-CST GET DISP-CSTSystem Commands CommandsCommands System CommandsGET DOOR-DESC SET DOOR-DESCUpgrading Firmware Before beginning the Upgrade processUpgrading Firmware via an IP Address Preparing the Master for communication via an IPVerifying and Upgrading the device firmware via an IP Assigning Communication Settings and TCP/IP SettingsSelect the device’s firmware file from the Files section FIG Panel Intercom Configuration Using the NetLinx ModuleIntercom Setup Incorporating an Intercom Panel Into Your NetLinx SystemSetting Intercom Auto Answer Setting the Intercom Session TimeoutDisabling All Doorbells Door SetupAssigning a Chime To a Doorbell Door Chime SetupAllowing a Panel To Be Monitored Advanced SetupAllowing a Panel To Monitor Naming a panelAnswering an incoming Intercom call Answering an Incoming Doorbell Call Someone At The DoorCreating Intercom Pages Advanced SetupEnding a Doorbell Call Name Description Channel Address PortCodeDoor Setup Door Chime SetupIntercom Demo Sample IntercomName Description Channel Address Level PortCode Panel Directory Room Name Name of a panel Setup SetupSomeone At The Door Someone At The DoorDoorbell Adjustments Popup Doorbell Adjustments popupCreating Popup Pages Door Answer Call popupIntercom Answer Call Popup Intercom Answer Call popupMore Time Popup More Time popupProgramming Metreau Entry Communicators It’s Your World Take Control