Excalibur electronic P95-LP3 installation manual P95-3 Zero Clearance Direct Vent Gas Fireplace

Page 1

www.excalibur-fire.com

P95-3 Zero Clearance Direct Vent Gas Fireplace

Owners &

Installation Manual

MODELS: P95-NG3 Natural Gas P95-LP3 Propane

WARNING:

 

 

FOR YOUR SAFETY

 

Iftheinformationintheseinstructionsarenotfollowedexactly,

What to do if you smell gas:

 

a fire or explosion may result causing property damage,

Do not try to light any appliance

personal injury or loss of life.

Do not touch any electrical switch:

 

 

 

do not use any phone in your

FOR YOUR SAFETY

building.

 

Do not store or use gasoline or other flammable vapours and

 

Immediately call your gas supplier

liquids in the vicinity of this or any other appliance.

from a neighbour's phone. Follow

 

 

 

Installation and service must be performed by a qualified

the gas supplier's instructions.

installer, service agency or the gas supplier.

If you cannot reach your

gas

 

 

 

supplier, call the fire department.

 

 

 

Tested by:

 

Installer: Please complete the details on the back cover

 

 

 

 

 

 

and leave this manual with the homeowner.

 

 

 

Homeowner: Please keep these instructions for future reference.

 

 

 

 

 

918-526

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

07/17/06

Image 1
Contents 07/17/06 P95-3 Zero Clearance Direct Vent Gas FireplaceTo the New Owner CongratulationsTable of Contents Copy of Safety Decal for P95-3 Safety LabelFor the State of Massachusetts only RequirementsGeneral Safety Information InstallationInstallation Checklist Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceOptional Heatwave Duct System KIT Optional Heat Release KITCombustible Mantels Framing DimensionsFraming Finishing Unit Base STAND-OFFSHearth Requirements Facing RequirementFacing Over 1 25mm Thick Floor Mounted Fireplaces Raised FireplacesTop Standoff Assembly Unit Assembly Prior to InstallationVenting Introduction Side Nailing StripsFPI Direct Vent System Flex Horizontal Terminations Only VentingExterior Vent Termination Locations Corner Installation Flat Wall Installation Wall Thickness Vent Length RequiredSimpson DURA-VENT Venting Alternate Horizontal Termination CapDescription Simpson DURA-VENT Venting Components ListParts not supplied by Dura-Vent FPI Direct Vent System Flex Venting Arrangements Horizontal TerminationsHorizontal Venting with Three 3 90o Elbows Horizontal Venting with Two 2 90o ElbowsOption + H1 Option + V1 H + H1Vertical Venting with Three 3 90o Elbows Vertical Venting with Two 2 90o ElbowsOption Simpson DURA-VENT Direct Vent GS System Venting Arrangements Vertical TerminationsInstallation Snorkel Terminations Below Grade InstallationContinue to assemble pipe lengths Vertical TerminationOffset Chart Installation ProceduresFor FPI Direct Vent System Flex GS 8 Nominal Diameter ID OffsetGAS Line Installation Pilot AdjustmentGAS Pipe Pressure Testing High ElevationInstallation of LPG Conversion Kit Installation of the DC Sparker Heat Shield Optional Brick Panels LOG SET InstallationPicture below is a view from the back of the burner Optional Screen Doors Glass Door InstallationFront Facade Tab ScrewSingle Door Accents Accent KIT InstallationWall Thermostat Thermostat Wire TableDo not cut the ground terminal off under any circumstances Wiring DiagramsFor Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Copy of the Lighting Plate Instructions Normal Operating Sounds of GAS AppliancesMaintenance To Install the Fans FAN MaintenanceShut the power off To Remove the FansRemoving Valve Installing ValveBrick panel is very fragile handle with care P95-3 Main Assembly Parts ListParts List P95-3 Burner Assembly & LOG SET Description P95-3 Flush Front AccessoriesWarranty Limited Lifetime WarrantyInstaller Please complete the following information