Wayne-Dalton 9400, AND 9600 Bottom Section, Vertical Track, Tools Needed Level

Page 14

6

Tools Needed:

Level

Bottom Section

Before installing the bottom section, the weather seal (may not be included) must be installed (see Preparing the Opening on page 10)

Center the bottom section in the door opening. Level section using wooden shims (if necessary) under the bottom section.

weather seal

door opening level

SECTION

 

BOTTOM

wooden shims

(if necessary)

7

Tools Needed:

3/16” Drill Bit

Power Drill

7/16” Socket

Driver

Tape Measure

Level

Vertical Track

IMPORTANT: The tops of the vertical tracks must be level from side to side. If the bottom section was shimmed to level it. The vertical track on the shimmed side, must be raised the height of the shim.

Position the left hand vertical track assembly over the rollers of the bottom section. Make sure the counterbalance cable is located between the rollers and the door jamb. Drill 3/16” pilot holes for the lag screws. Loosely fasten

cable drum fLAGANGLE

5/16” x 1-5/8”

LAG SCREWS

CABLE

VERTICAL

TRACK

ASSEMBLY

vertical track

BOTTOM SECTION

5/8” roller

LAG

LAG

SCREW

SCREW

locations

locations

 

jamb brackets and flagangle to the jamb using 5/16” x 1-5/8” lag screws. Tighten lag screw securing bottom jamb bracket to jamb, to maintain 5/8” spacing. Hang cable drum over flagangle. Repeat for the right hand side.

JAMB

BRACKET SECTION BOTTOM

12r qi flagangle 15r qi flagangle

quick install jamb bracket

LAG SCREW

locations

 

lag

12r & 15r Fully

screw

Adjustable flagangle

14

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Important Notice REV4 03/01/2012Table of Contents Package Contents Door Section Identification Tools Required Winding bars can cause spring Energy to be released Torsion Spring Removal For Standard LiftFailure to use approved Suddenly, resulting in severe Or fatal injuryTorqueMaster Spring Removal Unwind SpringsBracket and Drive Gear TorqueMaster SpringRemoval Tools Needed Recommended Tools from Extension Spring RemovalRemoving the Old Door Attach a suitable mounting pad to Preparing the OpeningFailure to securely Structurally sound framing could causeAngles to Vertical Track InstallationAttaching Quick Install Flag FlagangleTools Needed Hammer Horizontal AngleTools Needed None Installing Q.I. Jamb Brackets DrumsTools Needed Level Bottom SectionVertical Track Stacking Sections Top BracketsBar Bar AsymmetricalTo this DOOR, a Wayne-Dalton Operator BracketTop section ProperlyDoor Operation Important the DimensionTop Section Attaching Horizontal Track to Quick Install FlaganglePOSITION­ Causing Severe or Fatal Injury Do not Raise Door Until Horizontal Tracks are SECURED­Tracks are SECURED­ AT REAR, AS Attaching Horizontal Track to Adjustable FlagangleFall from Overhead POSITION­ Causing Severe or Fatal Injury Correct Top Adjusting Top BracketsMaintaining the slide’s position, tighten InCorrectTorqueMaster Spring Tube Must install the center bracket bushingDoorMaster Bracket installations on 40, Figure a Center Bracket BushingIdrive Installation Left Drum WrapsGarage Looking OUT Important Right and Left HandCable Drums End Brackets Assembly Securing Center BracketPositioning Support Bracket Tools Needed Pliers Attaching Disconnect CablesMounting Disconnect Handle Bracket Mark a location on the right jambDisconnect handle bracket. Tighten Attaching Disconnect HandleRemove all disconnect cable slack Handle until snug, and then tightenSecuring Door For Spring Winding Cable AdjustmentTools Needed Pliers/Wire Cutters Flat Tip Screwdriver Tools Needed Vice ClampsRecommended Spring Turns Drum Wrap InstallationWinding Springs Important pawl knob must be See the Spring Turn chart for Required number of turnsFrom vertical tracks IMPORTANT! Adjustments to SpringsRear Support Full Tension of the Spring Spring Turn ChartThree clicks Flagangles for level and plumbTorqueMaster Plus Reset InstructionsTorqueMaster Plus Reset Instructions PawlTo Add Spring Tension No spring winding on left hand sideClamp a pair of vice clamps on the vertical Wrench be used. Place the wrench ontoSide Lock DoorMaster TM BracketStep Plate Approximately 48 to 50 1220 to Pull RopeMeasure and mark the jamb No Scew EYE Pull Rope Bottom BracketTrack radius being used Assembly, as shown in FIGDetermine the Wayne-Dalton Appropriate 1/2 1 room permitting above of the highAbove high arc Operator hook-up charts, refer to referenced illustrationsPre-drilling and securing the wall bracket to header. Using From Center lineSuitable mounting Trolley OperatorOperator Rail Operator Framing Members Perforated AngleCleaning PaintingPainting Lifetime Limited Warranty Models 9100, 9400 Thank you for your purchase
Related manuals
Manual 10 pages 39.36 Kb Manual 8 pages 41.15 Kb Manual 40 pages 42.94 Kb Manual 36 pages 11.38 Kb

AND 9600, 9400 specifications

Wayne-Dalton is a renowned name in the garage door industry, and its series of garage doors, namely the 9600, 9400, and 9100, stand out for their exceptional quality, durability, and aesthetic appeal. Each series is designed to meet various needs, offering a range of features and technologies that enhance functionality and performance.

The Wayne-Dalton 9600 series is known for its energy efficiency and robust construction. These doors are insulated with a foamed-in-place polyurethane core, which provides an exceptional R-value, making them ideal for regions with extreme temperature fluctuations. The 9600 series features high-quality steel construction, ensuring durability and resistance to dents and damage. This series also offers a variety of design options, including wood grain textures and multiple color finishes, allowing homeowners to match their garage doors with their home’s exterior.

Moving to the Wayne-Dalton 9400 series, this line is recognized for its versatility and premium insulation. Like the 9600 series, the 9400 features a polyurethane core foamed between two layers of steel for superior thermal performance. Moreover, it offers a wider selection of panel designs, from traditional to contemporary finishes. The 9400 doors come equipped with a weather seal, enhancing protection against the elements and keeping the garage environment comfortable year-round.

Lastly, the Wayne-Dalton 9100 series combines affordability with functionality. It also offers insulated construction, although with a polystyrene core, making it an excellent choice for homeowners seeking a budget-friendly option without sacrificing quality. The 9100 series provides a good range of design options and customizable accessories such as decorative hardware, windows, and color choices to suit individual preferences.

All three series benefit from advanced technology, such as Wayne-Dalton's innovative design features for smooth operation and increased safety. They are equipped with sectional door designs, reducing the risk of pinch points and enhancing user safety. Additionally, Wayne-Dalton offers a variety of remote access and control technologies, ensuring convenience and peace of mind for users.

In summary, the Wayne-Dalton 9600, 9400, and 9100 series are distinguished by their superior insulation, durability, and stylish design options. Whether prioritizing energy efficiency, versatility, or budget considerations, these garage doors cater to a spectrum of consumer needs, thereby continuing Wayne-Dalton's legacy of excellence in design and functionality.
Top Page Image Contents