RIDGID 300 manual Removing Pipe From Threading Machine, Reaming Pipe With No Reamer

Page 12

300 Compact Pipe and Bolt Threading Machine

5.Turn carriage handwheel to bring dies against end of pipe. Slight pressure on handwheel will start dies (Figure 10).

Figure 8 – Reaming Pipe With No. 344 Reamer

4.Retract reamer and return reamer to UP position.

5.Release foot switch and remove your foot from the housing.

Threading Pipe or Rod With Quick-Opening, Self-Opening or Semi-Automatic Die Head

1.Install die set. Refer to die installation procedure.

2.Swing cutter and reamer to UP position.

3.Swing die head to DOWN position with throwout lever set to CLOSE position.

4.Check directional switch to insure it is in the FOR (Forward) position. Depress and hold the foot switch down with left foot.

NOTE! 300 Compact Machines have an automatic oil- ing system that brings oil to the work through the die head. Oil flow can be adjusted with oil flow control valve located on back side of carriage (Figure 9).

Increase Flow

Figure 9 – Oil Flow Control

Figure 10 – Threading Pipe With No. 811-A Quick Opening Die Head

6.Quick-Opening 811A Die Head (Figure 11) – When thread is completed, raise throwout lever to open position, retracting dies.

Self-Opening 815A Die Head (Figure 12) – When die head trigger contacts end of pipe, throwout lever is automatically opening.

Semi-automatic die head (Figure 13) – When the end of the pipe being threaded is flush with the end of the number 1 die, hit the handle for the dies to release the pipe.

7.Turn carriage handwheel to back die head off pipe.

8.Swing die head back to UP position.

Removing Pipe From

The Threading Machine

1.Use repeated and forceful clockwise spins of the speed chuck handwheel at the front of the Threading Machine to release the workpiece from the speed chuck jaws.

2.If necessary, loosen the rear centering device using a clockwise rotation of the handwheel at the rear of the Threading Machine.

3.Slide the workpiece out of the Threading Machine, keeping a firm grip on the workpiece as it clears the Threading Machine.

WARNING To avoid injury from falling parts or equip- ment tip-overs when handling long workpieces, make sure that the end farthest from the Threading Machine is supported prior to removal.

10

Ridge Tool Company

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Pipe and Bolt Table of Contents Compact Pipe and Bolt Threading Machine General Safety Information Electrical SafetyPersonal Safety Work AreaSpecific Safety Information ServiceFoot Switch Safety Machine SafetyDescription, Specifications and Standard Equipment SpecificationsModel No Compact Threading Machine with Foot Switch DescriptionMachine Assembly Mounting Machine To StandNo Folding Wheel Stand No A, 150A and 200A Universal StandStand Assembly Mounting Machine To BenchMachine Inspection Machine and Work Area Set-UpOperation Using Machine-Mounted Tools Installing Pipe In Threading Machine Cutting Pipe With No CutterReaming Pipe With No Reamer Removing Pipe From Threading Machine Reaming Pipe With No ReamerInstalling Dies In Self-Opening Die Head Right Hand Only Washer Index Line Head LinkSize Bar Installing Dies Model 816/817 Die Heads Checking Thread LengthSize Stop Handle Plunger Knob Short or Close Nipple Threading Procedure No Nipple ChuckPipe Adapters Stud Adapters Installing Nipple Chuck Body and Adapter Groover Adapter Bracket 300 CompactMaintenance Instructions AccessoriesAccessories For Threading Machine Oil System MaintenanceJaw Insert Replacement Machine StorageReplacing Brushes In Motor Motor Cover ScrewsService and Repair Wiring Diagrams115/230V Far East 230V 25-60 Hz115V 25-60 Hz 115V DomesticSuppressor NeutralMachine à fileter pour tuyaux et boulons modèle 300 Compact Table des matières Consignes générales de sécurité Sécurité électriqueSécurité personnelle Prise avec terre Barrette de terreService après-vente Sécurité de la pédale de commandeConsignes de sécurité spécifiques Utilisation et entretien de l’appareilDescription, Spécifications et Accessoires de Base Sécurité de l’appareilSpécifications Assemblage de la Machine Equipements de BaseMontage de la machine sur support Support roulant repliable NInstallation correcte de l’obturateur d’huile Supports universels nos 100A, 150A et 200A1224 AvantPré-2001 535-A/535Inspection de la machine Volant duChariot Capot PoignéePréparation de la Machine et du Chantier Installation des tuyaux dans la machine à fileter Utilisation des Outils à Montage DirectCoupe des tuyaux à l’aide du coupe-tubes n Alésage des tuyaux à l’aide de l’alésoir N Alésage des tuyaux à l’aide de l’alésoir nRetrait des tuyaux de la machine à fileter Rondelle Repère Tête Barre de Liaison Levier deBlocage Goupille cylindriqueVérification de la longueur des filetages Née complètement à gaucheButée FilièreMandrin à raccords n Filetage des manchons et des mamelonsAdaptateurs pour tiges Installation du mandrin à raccords Adaptateur de rainureuse n 916 pour 300 CompactAccessoires Accessoires pour machine à fileterEntretien LubrificationRemplacement des balais du moteur Remplacement des mâchoiresEntretien du système de lubrification Vis du Capot MoteurService après-vente Stockage de la machineSchémas électriques 115/230VExtrême Orient 230V/25-60HzSchémas électriques suite 115V américainMáquina Roscadora para tubos y pernos Compacta Índice Información general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personalInformación específica de seguridad Uso y cuidado de la máquinaServicio Seguridad del Interruptor de PieDescripción, especificaciones y equipo estándar Seguridad de la máquinaDescripción EspecificacionesMontaje de la máquina Equipo estándarMontaje de la máquina sobre un soporte Soporte abatible con ruedas NoSoportes Universales Modelos 100A, 150A ó 200A Montaje de la máquina sobre un banco Parte trasera de lasCompacta, 1233 y Detalle de la secciónRevisión de la máquina Preparación de la máquina y de la zona de trabajo Empleo de herramientas montadas a la máquina Corte de tubos con el cortatubos NoInstalación del tubo en la Máquina Roscadora Escariado de tubos con el Escariador No Figura 8 Escariado de tubos con el escariador NoCómo sacar el tubo de la Roscadora Figura 9 Regulación del flujo de aceiteFigura 11 Cabezal de Terrajas Universal de Apertura Rápida Verificación de la longitud de la rosca ManivelaPerilla del émbolo Mandril Niplero No Procedimiento para roscar niples cortosAdaptadores Adaptadores para Para tubería Pernos y vástagos Brazo adaptador para montar el Ranurador No a la Compacta Figura 16 Coloque la inserción dentro del Mandril NipleroAccesorios Accesorios para la máquina RoscadoraCabezales de terrajas ModeloInstrucciones para el mantenimiento LubricaciónRecambio de las piezas De inserción para la mordaza Mantenimiento del sistema de lubricaciónServicio y reparaciones Almacenamiento de la máquinaRecambio de las escobillas del motor Tornillos de la tapa del motorDiagramas de cableado 115/230v Lejano Oriente115V Nacional Máquina Roscadora para tubos y pernos Compacta Máquina Roscadora para tubos y pernos Compacta What is covered How you can get serviceWhat we will do to correct problems What is not covered

300 specifications

The RIDGID 300 is a highly regarded threading machine amongst plumbers and contractors, known for its durability, performance, and innovation in pipe threading. Designed for high-volume operations, this versatile tool can handle a wide range of pipe sizes, making it an indispensable asset in various plumbing projects.

One of the main features of the RIDGID 300 is its robust construction. Built to withstand rigorous use in demanding environments, the machine boasts a heavy-duty frame and components that contribute to its longevity. The compact design allows for portability, making it easy to transport to job sites, while its solid base provides stability during operation.

The RIDGID 300 employs advanced technologies that enhance its efficiency and performance. The machine is equipped with a powerful electric motor that delivers consistent and reliable performance, enabling users to complete threading tasks quickly and effectively. A unique gear drive system allows for smooth operation, reducing wear and tear on the equipment while ensuring precision in threading.

Another notable characteristic of the RIDGID 300 is its ability to accommodate various pipe materials. The machine is designed to handle iron, steel, and other common materials, making it a flexible choice for different applications. Additionally, it features a quick-change die head, enabling operators to switch pipe sizes rapidly, significantly increasing productivity on the job site.

The RIDGID 300 includes thoughtful safety features that help protect users during operation. Its integrated safety features reduce the risk of injury, allowing operators to focus on their work with confidence. Furthermore, the machine’s maintenance-friendly design allows for easy access to components, ensuring that routine servicing and repairs can be conducted with minimal downtime.

The versatility and adaptability of the RIDGID 300 make it suited for a variety of threading applications. Whether used in residential, commercial, or industrial environments, this threading machine consistently delivers outstanding results, earning it a reputation as a go-to tool for professionals in the plumbing industry. Its combination of power, durability, and thoughtful design elements ensure that the RIDGID 300 remains an essential piece of equipment for threading tasks, keeping pipelines secure and leak-free.
Top Page Image Contents