Mitsubishi Electronics SKM22ZD-S ON-TIMER operation procedure, Program Timer operation procedure

Page 13

ON-TIMER operation procedure

■If the room temperature is at near optimum temperature at the set time, the operation starts 5 to 60 minutes before the set time. Page 13

Example: In the case you wish to bring the temperature to nearly set temperature in at AM 8:00.

	HI POWER	ECONO
	AUTO	AM
	HI	AM
	HI
	MED
	LO
	ON
	FAN SPEED ON	OFF MODE

HI POWER TEMP ECONO

AIR FLOW

TIME CANCEL

ON OFF RESERVE

TIMER

TIMEACL

1	Press the ON TIMER button.
	ON TIMER indicator	ON is blinking.
2	Press the “ or	” button.

Each time the button is pressed, the indicator is switched in the order of:

AM	AM	AM	... AM	AM	...
0:00	0:10	0:20	1:00	1:10

Each time the button is pressed, the indicator is switched in the order of:

AM	PM	PM	...	PM	PM	...
0:00	11:50	11:40		11:00	10:50

Set at AM 8:00.

3 Press the RESERVE button.

The indication changes from blinking to steady lighting and the setting is complete. The timer light (yellow) is on.

⇓

•Operation starts 5 to 60 minutes before the set time.

•The TIMER light goes out at the set time.

Changing of set time

Set a new time by using the ON TIMER button.

Releasing procedure

Press the CANCEL button to turn off the timer indicator.

Program TIMER operation procedure

■The timer operations that consist of the combination of the timer being set at both on and off. Once this has been set and operations started, operations will commence and end at the same time every day as long as the ON/OFF button is not pressed.

Example: When it is desired to stop at 10:30 PM, and then start operation at 8:00 AM, near the set temperature.

HI POWER	ECONO
AUTO	PM
HI
MED
LO
ON	OFF
FAN SPEED ON	OFF MODE

HI POWER TEMP ECONO

AIR FLOW

TIME CANCEL

ON OFF RESERVE

TIMER

TIMEACL

Changing of set time

Set a new time by using the OFF TIMER or ON TIMER button.

1 Press the ON/OFF button.

■OFF TIMER operation setting

Set by the procedures on page 11.

PM

Set to .

OFF

■ON TIMER operation setting

Set by the above mentioned ON TIMER operation procedures.

	AM
Set to	.
	ON

The setting of the lighting of the timer lamp (yellow) of this unit is complete.

The time will be displayed on the remote control unit. The display will change depending on the operational status.

ON

OFF

ON

OFF

(Stopped)(Operating)

Releasing procedure

Press the CANCEL button to turn off the timer indicator.

– 12 –

Image 13

Contents USER’S Manual Contents Installation Precautions Safety precautionsOperation Precautions Do not install near places where inflammable gas may leakDo not sit on the outdoor unit nor put anything on it Precautions for Transfer or RepairsDo not touch the aluminum fins on the air heat exchanger Characteristics Choice of operations and featuresChoise of operations Indoor Unit Name of each part and its functionOutdoor Unit SCM45ZD-S SCM80ZD-S SCM60ZD-S How to close the suction grill How to open the suction grillRemoval, installation of suction grill Unit indication sectionOperation section Transmission procedureIndication section Temperature adjustment during Auto Auto mode operation procedureConcerning high power operation COOL/HEAT/DRY mode operation procedureConcerning economy operation Emergency run operation Air flow direction adjustment procedureAir scroll Swing FlapOFF-TIMER operation procedure Present time setting procedureProgram Timer operation procedure ON-TIMER operation procedureRemote control handling procedure About Timer operationAbout FAN Speed Replacing the batteriesOperating hints Set a suitable room temperatureAvoid direct sunlight and draught Before maintenance MaintenanceDuring the operational season At the end of the seasonSuitable installation position Has the unit been installed correctly?Feature Color Inspection and maintenanceRefrigerant oil recovery operation TroubleshootingAbout the Multiple Air-conditioner Simultaneous OperationPlease remember Power Blackout Auto Restart Function When to contact your distributor without delayAir conditioner operating conditions Page Inhalt Sicherheitsvorschriften Vorsichtsmassnahmen BEI DER InstallationVorsorge IM Betrieb Den Körper nicht längere Zeit dem Kühlluftstrom aussetzenDie Aluminiumrippen am Wärmetau VORSORGEMAßNAHMEN BEI Versetzung Oder ReparaturenScher nicht berühren Heit kontrollierenKennzeichen Unterschiedliche BetriebsartenInnengerät Namen der Teile und ihre FunktionenAussengerät SCM45ZD-S SCM80ZD-S SCM60ZD-S Öffnen des Ansaugluftgitters AnzeigenteilSchließen des Ansaugluftgitters ON/OFF Schalter des GerätesÜbermittlung BedienungsteilAuto Betrieb Temperatureinstellung bei AutoCOOL/HEAT/DRY Betrieb Zür Betriebsart HI PowerZür Betriebsart Economy Notbetrieb Einstellung der LuftströmungsrichtungMemory Flap Klappenstopp Verfahren zur Einstellung der aktuellen Zeit Betrieb des AusschalttimersBetrieb des Programm-TIMERS Betrieb des EinschalttimersDie Taste Einschalttimer drücken Einstellung des EINSCHALTTIMER-BetriebsUmgang mit der Fernbedienung Timer BetriebBatterien auswechseln Betriebshinweise Wenn die Fernbedienung nicht funktioniertBeim Umgang mit der Fernbedienung folgendes beachten Einstellung der üblichen Raum Filter regelmäßig reinigenVor der Wartung WartungWährend der Betriebssaison Bei Ende der SaisonAngemessene Installation Ist das Gerät einwandfrei installiert?Achten Sie auf das Betriebsgeräusch Gegenstand Merkmal FarbeFehlersuche Zur MehrfachklimaanlageGleichzeitiger Betrieb Automatischer BetriebBitte beachten Stromausfall-Neustartfunktion Betriebsbedingungen für die KlimaanlageSelbstdiagnose Kennzeichen beim Heat BetriebMechanismen und Leistung des Heat Betriebes EntfrostungAIR-CONDITIONER Division AIR-CONDITIONING & Refrigeration Systems Headquarters