Emerson 00825-0100-4530 Rev EC continued FOUNDATION fieldbus, Non-intrinsicallysafe power supply

Page 13
Step 3 continued...

March 2013

Quick Installation Guide

 

 

Step 3 continued...

FOUNDATION fieldbus

The Rosemount 5300 Series transmitter, FOUNDATION fieldbus version, operates with a power supply ranging from 9 - 32 Vdc (9 - 30 Vdc in IS applications and 16 - 32 Vdc in Explosion-proof / Flameproof and in Non-Sparking / Energy Limited applications).

FISCO, IS applications: 9 - 17.5 Vdc.

Non-intrinsically safe power supply

Rosemount 5300 Series

Transmitter

 

 

Power

 

 

Supply

 

Fieldbus

 

Field Communicator

Modem

PC

 

 

NOTE:

Rosemount 5300 Series Transmitters with Flameproof/Explosion-proof output have a built-in barrier; no external barrier needed.

Intrinsically safe power supply

Rosemount 5300 Series

Transmitter

Approved IS Barrier

Power

Supply

Fieldbus

Modem PC

Field Communicator

For IS Parameters, see the Product certifications chapter.

13

Image 13
Contents Quick Installation Guide 00825-0100-4530,Rev EC MarchSuperior Performance Guided Wave Radar Level and Interface TransmitterQuick Installation Guide About this guideProbes with non-conductingsurfaces March ContentsStep 1: Confirm system readiness Switch HART revision modeConfirm HART revision capability Confirm correct Device DriverTank connection with flange Step 2 Mount the transmitter head/probeThreaded tank connection Tri-Clamptank connectionBracket mounting, on wall Step 2 continuedBracket mounting, on pipe Step 2 continued Remote housingGrounding Step 3 Connect the wiringTerminal block To connect the transmitterIntrinsically safe power supply Non-intrinsicallysafe power supplyHART communication Step 3 continuedQuick Installation Guide Transient protection terminal blockPower PowerQuick Installation Guide Load limitationsNon-HazardousInstallations InstallationsNon-intrinsicallysafe power supply Step 3 continued FOUNDATION fieldbusIntrinsically safe power supply Power Consumption 0.5 W with HART address = RS-485with Modbus communicationQuick Installation Guide Step 3 continuedInstalling the Rosemount Radar Master software Step 4 Configure1Only for HART communication Run WizardFOUNDATION fieldbus parameters FOUNDATION fieldbus parameters FOUNDATION fieldbus parameters 3.Click Modbus Setup Setup - Modbus communication parametersInstallation Safety Instrumented Systems 4-20mA onlyConfiguration Table 3. Alarm levels and operation values Alarm and saturation levelsDamping Write protectionSite acceptance Operation and maintenanceProof test Inspection SpecificationsReferences Visual inspectionProduct certifications Safety Instrumented Systems SISEU conformity North-AmericancertificationsQuick Installation Guide Canadian Standards Association CSA approvalsDual seal maintenance I5, IE1 Intrinsically safe and FISCO modelATEX approvals European certificationsMarch Special conditions for safe useINMETRO approvals Brazilian certificationsQuick Installation Guide Special conditions for safe useMarch Chinese certificationsI21 Intrinsically safe IB1 FISCO modelQuick Installation Guide Japanese certificationsIC1 FOUNDATION fieldbus FISCO model N3 Type nIECEx approvals IECEx certificationsMarch Special conditions for safe useOverfill protection Other certificationsQuick Installation Guide Suitability for intended useFigure 1. EC Declaration of Conformity - page EC Declaration of ConformityQuick Installation Guide MarchQuick Installation Guide Figure 2. EC Declaration of Conformity - pageMarch Quick Installation Guide Figure 3. EC Declaration of Conformity - pageMarch 00825-0100-4530 Quick Installation Guide00825-0100-4530,Rev EC March Emerson Process Management Rosemount Measurement