KitchenAid W10526089A To Convert Standard Surface Burners, Gas pressure regulator

Page 18

Gas pressure regulator

4.Remove plastic cover from gas pressure regulator cap.

5.Turn gas pressure regulator cap (marked “N” on front of gas pressure regulator) counterclockwise with a wrench to remove.

NOTE: Do not remove the spring beneath the cap.

F

Side view before

A

N

B

F D E

Side view after

C

A. Plastic cover

B. Gas pressure regulator cap with solid end facing out C. Gas pressure regulator cap with hollow end facing out

D.Washer

E. Gas pressure regulator cap

F. Gas regulator shutoff valve (shown in the “open” position)

6.Turn the gas pressure regulator cap over and reinstall on regulator so that the hollow end faces out and letters “LP” are visible.

7.Replace plastic cover over gas pressure regulator cap.

To Convert Standard Surface Burners

1.Remove burner cap.

2.Using a T20® TORX® screwdriver, remove the burner base.

3.Apply masking tape to the end of a 7 mm nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside.

C

A

D

B

A. Igniter electrode

C. Burner cap

B. Gas tube opening

D. Burner base

4.Gas orifice spuds are stamped with a number, marked with

1 color dot, and have a groove in the hex area. Replace the Natural gas orifice spud with the correct LP gas orifice spud.

A

A. Groove

Refer to the following chart for correct LP gas orifice spud placement.

LP Gas Orifice Spud Chart for Standard Surface Burners

Burner Location

Burner Rating

Color

Size

Right front

5,000

Btu/h

Red

0.70 mm

Left front

13,000

Btu/h

Green

1.10 mm

Right rear

10,000

Btu/h

Blue

0.95 mm

Left rear

5,000

Btu/h

Red

0.70 mm

 

 

 

 

 

5.Place Natural gas orifice spuds in plastic parts bag for future use and keep with package containing literature.

6.Replace burner cap.

7.Repeat steps 1-6 for the remaining burners, except for the TripleTier® Flame burner (on some models). See “To Convert TripleTier® Flame Burners” in the “LP Gas Conversion” section.

To Convert TripleTier® Flame Burners (on some models)

1.Remove burner cap.

2.Remove the burner head using a size T20® TORX® screwdriver.

3.Remove the plate on the external gas orifice spud.

A

B

C

D

A. Burner caps

B. Burner heads

C. External gas orifice spud access plate

D. Internal gas orifice spud

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents W10526089A Range Safety Table DES MatièresWhat to do if YOU Smell GAS Parts needed Installation RequirementsTools and Parts Tools neededMobile Home Additional Installation Requirements Mobile home installations requireLocation Requirements Product Dimensions Freestanding Range Slide-in RangeInstallation Clearances Freestanding RangesSlide-In Ranges Type of Gas Electrical RequirementsGas Supply Requirements Gas Supply LineBurner Input Requirements Gas Supply Pressure TestingCountertop Preparation Gas Pressure RegulatorMeasure for Proper Height Installation InstructionsUnpack Range Slide-In RangesFloor Mounting Adjust Leveling LegsInstall Anti-Tip Bracket Wall MountingLevel Range Verify Anti-Tip Bracket Is Installed EngagedRemove Warming or Storage Drawer To Remove Warming DrawerTypical rigid pipe connection Make Gas ConnectionTypical flexible connection Complete ConnectionCheck Operation of Cooktop Burners Standard Surface Burners Initial lighting and gas flame adjustmentsElectronic Ignition System TripleTier Flame BurnerTo adjust standard burners Adjust Flame Height Check Operation of Oven Bake BurnerAdjust Oven Bake Flame if needed If the low flame needs to be adjustedComplete Installation Replace Oven Racks and Warming or Storage DrawerTo Convert Gas Pressure Regulator GAS ConversionsLP Gas Conversion Turn manual shutoff valve to the closed positionGas pressure regulator To Convert Standard Surface BurnersTo Convert TripleTier Flame Burners on some models Remove plastic cover from gas pressure regulator capPlate External gas orifice spud Internal gas orifice spud To Convert Oven Broil BurnerTo Convert Oven Bake Burner Locking screw Orifice hoodNatural Gas Conversion To Convert TripleTier Flame Burner on some models Stamped numberTo Convert Oven Broil Burner Sécurité DE LA Cuisinière Votre sécurité et celle des autres est très importantePied de La cuisinière Exigences D’INSTALLATION Exigences demplacementOutillage et pièces Cuisinière encastrable Dimensions du produit Cuisinière autoportante64 cm 30⁹⁄₁₆ 77,6 cm 30 76,2 cm ³⁄₄ 14,6 cm B 76,2 cmDégagements de séparation à respecter Cuisinières autoportantesCuisinières encastrables Type de gaz Spécifications électriquesSpécifications de l’alimentation en gaz Gaz naturelDébit thermique des brûleurs Canalisation dalimentation en gazDétendeur Tests de pressurisation de la canalisation de gazDéballage de la cuisinière Instructions DinstallationPréparation du plan de travail Mesures pour une hauteur appropriéeInstallation de la bride antibasculement Réglage des pieds de nivellementRetrait du tiroir de remisage Retrait du tiroir-réchaud ou du tiroir De remisageRetrait du tiroir-réchaud Montage au plancherSur les modèles avec tiroir-réchaud Réglage de laplomb de la cuisinièreSur les modèles avec tiroir de remisage Sur les cuisinières équipées de tiroirs de remisageRaccordement typique à une canalisation rigide Raccordement à la canalisation de gazRaccordement typique par raccord flexible Compléter le raccordementAllumage initial et réglages des flammes Système dallumage électroniqueCuisinière encastrable Brûleur TripleTierContrôle du fonctionnement du brûleur de cuisson au four Si le brûleur ne sallume pas correctementRéglage de la taille des flammes Réglage des brûleurs standardContrôle du fonctionnement du brûleur du gril Réinstallation du tiroir-réchaudRéinstallation du tiroir de remisage Sil est nécessaire de régler la taille des flammesAchever l’installation Si vous avez besoin dassistance ou de serviceSi la cuisinière ne fonctionne pas, contrôler ce qui suit Conversion du détendeur Conversions Pour Changement DE GAZConversion pour lalimentation au propane Important Ne pas enlever le détendeurConversion des brûleurs standard de la table de cuisson DétendeurPlaque Gicleur externe Gicleur interne Conversion du brûleur de cuisson au fourConversion du brûleur du gril Injecteur femelle BrocheConversion pour lalimentation au gaz naturel Conversion des brûleurs standard de surfaceChiffre gravé Ôter les grilles du four

W10526089A specifications

The KitchenAid W10526089A is a highly efficient and versatile appliance that serves as a replacement water filter, designed specifically for select KitchenAid refrigerators. This model ensures that you and your family can enjoy clean, fresh-tasting water and ice. One of its main features is the ability to reduce contaminants commonly found in tap water, including chlorine, lead, and sediment, ensuring a healthier drinking experience.

One of the standout technologies in the W10526089A is its advanced filtration system, which includes activated carbon. This technology works effectively to absorb impurities that can affect the taste and purity of water. Not only does it enhance flavor, but it also helps in removing odors, delivering crisp and refreshing hydration. The filter is designed to provide up to six months of use, depending on water quality and consumption, which ensures that you get great performance without frequent replacements.

Installation of the W10526089A is straightforward, making it easy for homeowners to replace their existing filter without needing professional assistance. It features a simple twist-and-lock design that allows for quick and hassle-free changes. This ease of use is a significant benefit, particularly for busy families who rely on continual access to filtered water.

In terms of characteristics, the W10526089A is designed to fit within specific KitchenAid refrigerator models, ensuring seamless compatibility. Its compact size allows it to fit discreetly behind the refrigerator’s interior, maintaining aesthetic appeal while ensuring functionality. Additionally, the filter carries the NSF International certification, which verifies that it meets strict public health standards for water filtration safety and performance.

The W10526089A also comes with a clear indicator that alerts users when it’s time to replace the filter, promoting better maintenance and ensuring your water remains pure at all times. This intelligent feature minimizes the guesswork involved with water filter replacement, leading to improved health and convenience.

Overall, the KitchenAid W10526089A water filter is a reliable investment for anyone looking to improve their home’s drinking water quality, offering advanced filtration technologies, user-friendly design, and a commitment to safety and performance.
Top Page Image Contents