Frymaster warranty Operator’S Manual, FRYMASTER BIELA14 SERIES GEN II LOV, Electric Fryer

Contents FRYMASTER BIELA14 SERIES GEN II LOV OPERATOR’S MANUALELECTRIC FRYER FOR YOUR SAFETYNOTICE TO U.S. CUSTOMERS NOTICENOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS CANADADANGER Adding New Product Menu Items Product Selection M3000 Menu Summary TreeSee section 4.10.2B.WARRANTY PROVISIONS - FRYPOTS A.WARRANTY PROVISIONS - FRYERSD.WARRANTY EXCLUSIONS C.PARTS RETURN•overtime or holiday charges This warranty also does not coverBIELA14 SERIES GEN II LOV ELECTRIC FRYER 1.2Safety InformationCHAPTER 1: INTRODUCTION 1.1General1.3Computer Information for the M3000 Computers 1.5Installation, Operating, and Service Personnel1.4European Community CE Specific Information CE StandardWhat to do if your equipment arrives damaged 1.7Shipping Damage Claim Procedure1.8Service Information NOTICE 2.1General Installation Requirements2.1.2 Electrical Grounding Requirements 2.1.3 Australian Requirements 2.2Power RequirementsDANGER CHAPTER 3: OPERATING INSTRUCTIONS TYPICAL CONFIGURATION BIELA314 SHOWNM3000 COMPUTER 3.1Equipment Setup and Shutdown Procedures3.3.2 Install the Oil Reservoir 3.3 Low Oil Volume Automatic Refill3.3.1 Prepare the System for Use 3.3.3 Routine Oil Changes3.3.4Bulk Oil Systems FR FRIES 4.1M3000 General Information4.2Basic Operation 4.3Cooking with Multi-ProductDisplay 4.4Cooking with Dedicated Display <<<< >>>> 4.5Changing from Breakfast Setup to Lunch<<<<>>>>; an alarm will sound Press and quickly4.6Changing from Lunch Setup to Breakfast 4.7.1 Navigation Buttons 4.7M3000 Button Description and Functions4.7.2 Filter, Temperature and Info Buttons 4.7.3 Cook Channel and Selection ButtonsSee section 4.8M3000 Menu Summary Tree4.10.2 4.10.31234 4.9Fryer Setup Mode Programming24hR 4.10.1 Escape Menu Items 4.10 M3000 Common Tasksfull 1.Escaping out of a menu or sub-menuproduct selectionPROD COOK ID DISABLE Product selection prompt 4.10.3 Storing Menu Items in Product Buttons4.10.4.1 Disposal for Non-BulkOil Systems 4.10.4.2 Refilling JIB Oil Systems 2. Press the u INFO button and scroll to dispose When finished, the computer displays REMOVE PAN4. To dispose press the 1 yes button to continue The computer displays DRAINING4.11 Filter Menu 4.11.1 Accessing the Filter Menua. auto filter b. maint filter4.11.2 Drain to Pan yes no 4.11.3 Fill Vat from Drain Pan4.11.4 Fill Vat from Bulk 4.11.5 Pan to Waste 4.12 Programming Level Onee. Fryer setup c. DEEP CLEAN MODEa.disabled b.enabled 4.12.1 AIF CLOCKselection display 4.12.2DEEP CLEAN MODE BOIL-OUTYes No EMPTY? and Yes NO DANGER 4.12.3 HIGH-LIMITTEST MODE comp 4.13 Programming Level Two4.13.1 PRODUCT COMP MODE c. password SETUPa. Prod comp b. e-log4.13.2 E-LOGMODE 4.13.3 PASSWORD SETUP MODE4.13.4 ALERT TONE MODE 4.13.5 FILTER AFTER 4.13.6 FILTER TIME 4.14 INFO ModeSPLIT VAT CONFIGURATION FULL VAT CONFIGURATION4.14.1 FILTER STATS MODE a. filter statsa. DAY wed, DATE 03/20/07 – Current day and date 4.14.2 REVIEW USAGE MODE4321 FULL / SPLIT VAT CONFIGURATION4.14.3LAST LOAD MODE 4-38 5.Press the 2 button again to quit5.1Introduction CHAPTER 5: FILTRATION INSTRUCTIONSThe filter pad or paper MUST be replaced daily 5.2Preparing the Filter for Use5.3 Auto Intermittent Filtration AIF 5.3.1 Auto Demand Filtration DRAINING, WASHING and FILLING during the process2. Press the 9 1 yes button to continue 9.Press 9 1 yes to silence alarm and continue prompt for SYSTEM ERROR 5.4.4 Filter Error Flowchart5.5Manual or End of Day Filtration MAINT FLTR 5.4.5 Filter BusyThe filter pad or paper must be replaced daily 2.Press the uINFO button to scroll to maInT fIltEr 9. Press the 9 1 yes button to continue 6.1.2Clean the Built-inFiltration System – Daily 6.1Cleaning the Fryer DANGER6.1.3Clean Behind Fryers – Weekly Replace the O-rings Deep Clean Boiling Out the Frypot6.2Annual/Periodic System Inspection FryerBuilt-InFiltration System 7.1 Introduction Problem Problem7.2Troubleshooting 7.2.1 Computer and Heating Problems7.2.3 Filtration Problems Corrective Action 7.2.4 Auto Top-OffProblemsError Log Codes 7.2.5 Bulk Oil System ProblemsProbable Causes 7.2.6is missing 8.1Wiring Diagrams 8.1.1Component Wiring Domestic CHAPTER 8: WIRING DIAGRAMS8.1.2Component Wiring CE 8.1.3Component Wiring CSA 8.1.4Component Wiring Australia 8.1.5Contactor Box – Delta Configuration 8.1.6 Contactor Box – WYE Configuration START OF 6-WIRE DATA & POWER 8.1.7 BIELA14 Series GEN II LOV Simplified Wiring8051734Q Page NOTE: Do NOT overfill the jug A.1.1 Bulk Oil SystemsFigure 2: Position the melter APPENDIX C: Solid Shortening Melter Use FAX Parts SERVICE HOTLINEFAX Tech Support 1-800-551-8633