Frymaster BIELA14 warranty Press the 9 1 yes button to continue

Page 60

2. Press the 9 (1 yes) button to continue.

2. Press the 9 (1 yes) button to continue.

The computer displays filter NOW? Alternating with YES/NO.

3. Go to step 1 section 5.3 on page 5-2 to continue.

5.4Troubleshooting the Auto Intermittent Filtration (AIF) 5.4.1 Incomplete Filtration

Should the AIF procedure fail after the filter pad was changed an error message is generated. Use the chart on page 5-6 to clear the error.

The computer displays IS VAT FULL? alternating with yes no. The MIB board displays three horizontal lines.

1.If the vat is full press the 9 (1 yes) button to continue. The computer returns to idle cook mode or OFF.

If the pot is not filled completely continue to next step.

2. Press 8 (2 NO) if pot is not filled completely.

The computer displays FILLING while the pump runs again. When the pump stops, the computer displays IS VAT FULL? alternating with yes no again. If the vat is full go to step 1. If the vat is not completely filled continue.

3. Press 8 (2 NO) if pot is not filled completely.

The computer displays FILLING while the pump runs again. When the pump stops, the computer displays IS VAT FULL? alternating with yes no again. If the vat is full go to step 1. If the vat is not completely filled continue.

4.Press 8 (2 NO) if pot is not filled completely. If this is the second consecutive sequence of incomplete filtration skip to step 8.

The computer displays CHANGE FILTER PAD? alternating with YES NO and an alarm.

5. Press 9 (1 yes) to continue.

Pressing 8 (2 NO) allows the fryer to return to cook mode in most cases for four minutes or 15 minutes if the pad is expired*, ending with the CHANGE FILTER PAD? alternating with YES NO display. This repeats until YES is chosen.

5-4

Image 60

Contents OPERATOR’S MANUAL FRYMASTER BIELA14 SERIES GEN II LOVELECTRIC FRYER FOR YOUR SAFETYNOTICE NOTICE TO U.S. CUSTOMERSNOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS CANADADANGER M3000 Menu Summary Tree Adding New Product Menu Items Product SelectionSee section 4.10.2A.WARRANTY PROVISIONS - FRYERS B.WARRANTY PROVISIONS - FRYPOTSD.WARRANTY EXCLUSIONS C.PARTS RETURNThis warranty also does not cover •overtime or holiday charges1.2Safety Information BIELA14 SERIES GEN II LOV ELECTRIC FRYERCHAPTER 1: INTRODUCTION 1.1General1.5Installation, Operating, and Service Personnel 1.3Computer Information for the M3000 Computers1.4European Community CE Specific Information CE Standard1.7Shipping Damage Claim Procedure What to do if your equipment arrives damaged1.8Service Information 2.1General Installation Requirements NOTICE2.1.2 Electrical Grounding Requirements 2.2Power Requirements 2.1.3 Australian RequirementsDANGER TYPICAL CONFIGURATION BIELA314 SHOWN CHAPTER 3: OPERATING INSTRUCTIONS3.1Equipment Setup and Shutdown Procedures M3000 COMPUTER3.3 Low Oil Volume Automatic Refill 3.3.2 Install the Oil Reservoir3.3.1 Prepare the System for Use 3.3.3 Routine Oil Changes3.3.4Bulk Oil Systems 4.1M3000 General Information FR FRIES4.2Basic Operation 4.3Cooking with Multi-ProductDisplay 4.4Cooking with Dedicated Display 4.5Changing from Breakfast Setup to Lunch <<<< >>>><<<<>>>>; an alarm will sound Press and quickly4.6Changing from Lunch Setup to Breakfast 4.7M3000 Button Description and Functions 4.7.1 Navigation Buttons4.7.2 Filter, Temperature and Info Buttons 4.7.3 Cook Channel and Selection Buttons4.8M3000 Menu Summary Tree See section4.10.2 4.10.34.9Fryer Setup Mode Programming 123424hR 4.10 M3000 Common Tasks 4.10.1 Escape Menu Itemsfull 1.Escaping out of a menu or sub-menuselection productPROD COOK ID DISABLE 4.10.3 Storing Menu Items in Product Buttons Product selection prompt4.10.4.1 Disposal for Non-BulkOil Systems 4.10.4.2 Refilling JIB Oil Systems When finished, the computer displays REMOVE PAN 2. Press the u INFO button and scroll to dispose4. To dispose press the 1 yes button to continue The computer displays DRAINING4.11.1 Accessing the Filter Menu 4.11 Filter Menua. auto filter b. maint filter4.11.2 Drain to Pan 4.11.3 Fill Vat from Drain Pan yes no4.11.4 Fill Vat from Bulk 4.12 Programming Level One 4.11.5 Pan to Wastec. DEEP CLEAN MODE e. Fryer setupa.disabled b.enabled 4.12.1 AIF CLOCK4.12.2DEEP CLEAN MODE BOIL-OUT selection displayYes No EMPTY? and Yes NO DANGER 4.12.3 HIGH-LIMITTEST MODE 4.13 Programming Level Two compc. password SETUP 4.13.1 PRODUCT COMP MODEa. Prod comp b. e-log4.13.3 PASSWORD SETUP MODE 4.13.2 E-LOGMODE4.13.4 ALERT TONE MODE 4.13.5 FILTER AFTER 4.14 INFO Mode 4.13.6 FILTER TIMEFULL VAT CONFIGURATION SPLIT VAT CONFIGURATION4.14.1 FILTER STATS MODE a. filter stats4.14.2 REVIEW USAGE MODE a. DAY wed, DATE 03/20/07 – Current day and dateFULL / SPLIT VAT CONFIGURATION 43214.14.3LAST LOAD MODE 5.Press the 2 button again to quit 4-38 CHAPTER 5: FILTRATION INSTRUCTIONS 5.1Introduction The filter pad or paper MUST be replaced daily 5.2Preparing the Filter for Use5.3 Auto Intermittent Filtration AIF DRAINING, WASHING and FILLING during the process 5.3.1 Auto Demand Filtration2. Press the 9 1 yes button to continue 9.Press 9 1 yes to silence alarm and continue 5.4.4 Filter Error Flowchart prompt for SYSTEM ERROR5.4.5 Filter Busy 5.5Manual or End of Day Filtration MAINT FLTRThe filter pad or paper must be replaced daily 2.Press the uINFO button to scroll to maInT fIltEr 9. Press the 9 1 yes button to continue 6.1Cleaning the Fryer DANGER 6.1.2Clean the Built-inFiltration System – Daily6.1.3Clean Behind Fryers – Weekly Deep Clean Boiling Out the Frypot Replace the O-rings6.2Annual/Periodic System Inspection FryerBuilt-InFiltration System 7.1 Introduction Problem Problem7.2Troubleshooting 7.2.1 Computer and Heating Problems7.2.3 Filtration Problems 7.2.4 Auto Top-OffProblems Corrective Action7.2.5 Bulk Oil System Problems Error Log CodesProbable Causes 7.2.6is missing CHAPTER 8: WIRING DIAGRAMS 8.1Wiring Diagrams 8.1.1Component Wiring Domestic8.1.2Component Wiring CE 8.1.3Component Wiring CSA 8.1.4Component Wiring Australia 8.1.5Contactor Box – Delta Configuration 8.1.6 Contactor Box – WYE Configuration 8.1.7 BIELA14 Series GEN II LOV Simplified Wiring START OF 6-WIRE DATA & POWER8051734Q Page A.1.1 Bulk Oil Systems NOTE: Do NOT overfill the jugFigure 2: Position the melter APPENDIX C: Solid Shortening Melter Use SERVICE HOTLINE FAX PartsFAX Tech Support 1-800-551-8633

Related manuals

Manual 26 pages 13.97 Kb

Manual 96 pages 23.21 Kb