Frymaster BIELA14 warranty 3.3.4Bulk Oil Systems

Page 18
3.3.4Bulk Oil Systems

1.Open the cabinet and slide the JIB from the cabinet (see Figure 5).

2.Remove the cap and pour any remaining oil in the container into all fry vats equally (see Figure 6).

 

Figure 6

 

Figure 5

3. With

the replacement jug upright 4. Put the tube in the new full container (see Figure 8).

remove the cap and foil seal (see

Figure

7).

Figure 7

WARNING:

Do not add HOT or USED oil to a JIB.

Figure 8

5.Slide the JIB onto the shelf inside the fryer cabinet (as seen in Figure 5).

6.Press and hold the orange JIB reset switch until the orange JIB LED is no longer illuminated (see Figure 9).

Figure 9

3.3.4Bulk Oil Systems

Instructions for installing and using bulk oil systems are found in Appendix A located at the rear of this manual.

3–4

Image 18
Contents ELECTRIC FRYER OPERATOR’S MANUALFRYMASTER BIELA14 SERIES GEN II LOV FOR YOUR SAFETYNOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS NOTICENOTICE TO U.S. CUSTOMERS CANADADANGER See section M3000 Menu Summary TreeAdding New Product Menu Items Product Selection 4.10.2D.WARRANTY EXCLUSIONS A.WARRANTY PROVISIONS - FRYERSB.WARRANTY PROVISIONS - FRYPOTS C.PARTS RETURNThis warranty also does not cover •overtime or holiday chargesCHAPTER 1: INTRODUCTION 1.2Safety InformationBIELA14 SERIES GEN II LOV ELECTRIC FRYER 1.1General1.4European Community CE Specific Information 1.5Installation, Operating, and Service Personnel1.3Computer Information for the M3000 Computers CE Standard1.7Shipping Damage Claim Procedure What to do if your equipment arrives damaged1.8Service Information 2.1General Installation Requirements NOTICE2.1.2 Electrical Grounding Requirements 2.2Power Requirements 2.1.3 Australian RequirementsDANGER TYPICAL CONFIGURATION BIELA314 SHOWN CHAPTER 3: OPERATING INSTRUCTIONS3.1Equipment Setup and Shutdown Procedures M3000 COMPUTER3.3.1 Prepare the System for Use 3.3 Low Oil Volume Automatic Refill3.3.2 Install the Oil Reservoir 3.3.3 Routine Oil Changes3.3.4Bulk Oil Systems 4.1M3000 General Information FR FRIES4.2Basic Operation 4.3Cooking with Multi-ProductDisplay 4.4Cooking with Dedicated Display <<<<>>>>; an alarm will sound 4.5Changing from Breakfast Setup to Lunch<<<< >>>> Press and quickly4.6Changing from Lunch Setup to Breakfast 4.7.2 Filter, Temperature and Info Buttons 4.7M3000 Button Description and Functions4.7.1 Navigation Buttons 4.7.3 Cook Channel and Selection Buttons4.10.2 4.8M3000 Menu Summary TreeSee section 4.10.34.9Fryer Setup Mode Programming 123424hR full 4.10 M3000 Common Tasks4.10.1 Escape Menu Items 1.Escaping out of a menu or sub-menuselection productPROD COOK ID DISABLE 4.10.3 Storing Menu Items in Product Buttons Product selection prompt4.10.4.1 Disposal for Non-BulkOil Systems 4.10.4.2 Refilling JIB Oil Systems 4. To dispose press the 1 yes button to continue When finished, the computer displays REMOVE PAN2. Press the u INFO button and scroll to dispose The computer displays DRAININGa. auto filter 4.11.1 Accessing the Filter Menu4.11 Filter Menu b. maint filter4.11.2 Drain to Pan 4.11.3 Fill Vat from Drain Pan yes no4.11.4 Fill Vat from Bulk 4.12 Programming Level One 4.11.5 Pan to Wastea.disabled b.enabled c. DEEP CLEAN MODEe. Fryer setup 4.12.1 AIF CLOCK4.12.2DEEP CLEAN MODE BOIL-OUT selection displayYes No EMPTY? and Yes NO DANGER 4.12.3 HIGH-LIMITTEST MODE 4.13 Programming Level Two compa. Prod comp c. password SETUP4.13.1 PRODUCT COMP MODE b. e-log4.13.3 PASSWORD SETUP MODE 4.13.2 E-LOGMODE4.13.4 ALERT TONE MODE 4.13.5 FILTER AFTER 4.14 INFO Mode 4.13.6 FILTER TIME4.14.1 FILTER STATS MODE FULL VAT CONFIGURATIONSPLIT VAT CONFIGURATION a. filter stats4.14.2 REVIEW USAGE MODE a. DAY wed, DATE 03/20/07 – Current day and dateFULL / SPLIT VAT CONFIGURATION 43214.14.3LAST LOAD MODE 5.Press the 2 button again to quit 4-38The filter pad or paper MUST be replaced daily CHAPTER 5: FILTRATION INSTRUCTIONS5.1Introduction 5.2Preparing the Filter for Use5.3 Auto Intermittent Filtration AIF DRAINING, WASHING and FILLING during the process 5.3.1 Auto Demand Filtration2. Press the 9 1 yes button to continue 9.Press 9 1 yes to silence alarm and continue 5.4.4 Filter Error Flowchart prompt for SYSTEM ERROR5.4.5 Filter Busy 5.5Manual or End of Day Filtration MAINT FLTRThe filter pad or paper must be replaced daily 2.Press the uINFO button to scroll to maInT fIltEr 9. Press the 9 1 yes button to continue 6.1Cleaning the Fryer DANGER 6.1.2Clean the Built-inFiltration System – Daily6.1.3Clean Behind Fryers – Weekly 6.2Annual/Periodic System Inspection Deep Clean Boiling Out the FrypotReplace the O-rings FryerBuilt-InFiltration System 7.1 Introduction 7.2Troubleshooting ProblemProblem 7.2.1 Computer and Heating Problems7.2.3 Filtration Problems 7.2.4 Auto Top-OffProblems Corrective ActionProbable Causes 7.2.5 Bulk Oil System ProblemsError Log Codes 7.2.6is missing CHAPTER 8: WIRING DIAGRAMS 8.1Wiring Diagrams 8.1.1Component Wiring Domestic8.1.2Component Wiring CE 8.1.3Component Wiring CSA 8.1.4Component Wiring Australia 8.1.5Contactor Box – Delta Configuration 8.1.6 Contactor Box – WYE Configuration 8.1.7 BIELA14 Series GEN II LOV Simplified Wiring START OF 6-WIRE DATA & POWER8051734Q Page A.1.1 Bulk Oil Systems NOTE: Do NOT overfill the jugFigure 2: Position the melter APPENDIX C: Solid Shortening Melter Use FAX Tech Support SERVICE HOTLINEFAX Parts 1-800-551-8633
Related manuals
Manual 26 pages 13.97 Kb Manual 96 pages 23.21 Kb