Maytag W10206488A installation instructions Vacation and Moving Care, To shut down the ice maker

Page 10

9.Remove, clean and replace the ice scoop and ice scoop holder.

After removing the ice scoop, remove the holder by removing the two thumb screws.

Wash the ice scoop holder along with the other interior components using the following instructions.

Replace the ice scoop holder by replacing the thumb screws.

A

B

A. Thumb screws

B. Ice scoop holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in dishwasher. They cannot withstand temperatures above 145°F (63°C).

11.Replace water pan by pushing back on the bottom with one hand while pushing up and back on the top. Secure the water pan by replacing both screws.

12.Check the following:

Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Replace the plastic cutter grid cover and the two screws.

15.Plug in ice maker or reconnect power.

Vacation and Moving Care

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

To shut down the ice maker:

1.Unplug ice maker or disconnect power.

2.Remove all ice from storage bin.

3.Shut off the water supply.

4.Remove the two screws in the lower access panel and the two screws from the base grille area of the front panel support. Pull forward to remove the lower access panel.

5.Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace lower access panel and screws.

7.Drain water from water pan by removing the drain cap.

8.If the room temperature will drop below 32°F (0°C), water must be removed from the drain line.

For ice makers with a drain pump installed:

Plug in ice maker or reconnect power.

Turn ice maker off and remove all remaining ice from ice bin.

Pour 1 qt (0.95 L) of water into the ice bin near the drain and let the unit stand for approximately 5 minutes. This will allow the water in the bin to drain into the drain pump so that the pump will remove the remaining water from the ice bin and the drain pump.

Unplug ice maker or disconnect power.

9.Before using again, clean the ice maker and storage bin.

10.Plug into a grounded 3 prong outlet.

NOTE: All components of the ice maker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

10

Image 10
Contents ICE Maker Safety ICE Maker User InstructionsUnpack the Ice Maker Installation InstructionsCleaning Before Use Location RequirementsLeveling Electrical RequirementsWater Supply Requirements Recommended grounding methodConnect Water Supply Connecting the Water LineRear View Gravity Drain System Connecting the DrainDrain Connection Drain Pump System on some modelsIce Maker Door How Your Ice Maker Works ICE Maker USENormal Sounds Reverse Door CatchUsing the Controls CleaningICE Maker Care Interior Components CondenserDirty or clogged condenser Vacation and Moving Care For ice makers with a drain pump installedTo shut down the ice maker Ice Maker Operation TroubleshootingIce Production Plumbing Problems Ice QualityItems Excluded from Warranty Maytag Major Appliance WarrantyLimited Warranty This limited warranty does not coverInstrucciones Para EL Usuario DE LA Fábrica DE Hielo Seguridad DE LA Fábrica DE HieloRequisitos de ubicación Instrucciones DE InstalaciónDesempaque la fábrica de hielo Cómo quitar los materiales de empaqueNivelación Requisitos eléctricosRequisitos del suministro de agua Método recomendado para la conexión a tierraConexión de la tubería de agua Conexión del suministro de aguaVista Posterior Sistema de la bomba de desagüe en algunos modelos Conexión del desagüeSistema de desagüe por gravedad Conexión del desagüeInvierta las bisagras Puerta de la fábrica de hieloQuite la puerta Vuelva a colocar la puertaBisagra inferior Sonidos normalesBisagra superior Cómo invertir el seguro de la puertaCómo funciona su fábrica de hielo USO DE LA Fábrica DE HieloUso de los controles Superficies exteriores Cuidado DE LA Fábrica DE HieloLimpieza Sistema de la fábrica de hieloPiezas interiores Para apagar la fábrica de hielo Su fábrica de hielo no funciona Solución DE ProblemasProducción de hielo La fábrica de hielo parece ser ruidosaProblemas de plomería Calidad del hieloExclusiones DE LA Garantía DE MaytagGarantía Limitada Esta garantía limitada no cubreInstructions Dutilisation DU Machine À Glaçons Sécurité DE LA Machine À GlaçonsDéballage de la machine à glaçons Instructions D’INSTALLATIONExigences demplacement Enlèvement des matériaux d’emballageNivellement Méthode de mise à la terre recommandéeSpécifications électriques Alimentation en eau par osmose inverseRaccordement du tuyau d’eau VUE ArrièreRaccordement du conduit dévacuation Vidange par gravitéSystème avec pompe de vidange sur certains modèles VUE LatéraleInversion des charnières Réinstallation de la portePorte de la machine à glaçons Dépose de la porteCharnière inférieure Sons normauxCharnière supérieure Inversion du loquet de porteTémoin Service Utilisation des commandesMode Lock verrouillage Utilisation DE LA Machine À GlaçonsTémoin indicateur de la nécessité d’un nettoyage Entretien DE LA Machine À GlaçonsNettoyage Surfaces extérieuresNettoyage des composants intérieurs CondenseurUn condenseur sale ou bouché Arrêt de la machine à glaçons Ou un déménagementMachine à glaçons avec pompe de vidange La machine à glaçons ne fonctionne pas DépannageProduction de glaçons La machine à glaçons semble bruyanteLa grille ne découpe pas les plaques de glace Qualité des glaçonsProblèmes de plomberie Goût, odeur ou couleur grise des glaçonsArticles Exclus DE LA Garantie Garantie LimitéeLa présente garantie limitée ne couvre pas W10206510A EN/FR PN W10206488A