Vita-Mix The Quiet One manual Corrupt Data

Page 23

Problems:

Possible Actions:

• Display window reads

Turn the machine off and on

“CORRUPT DATA”

again to reset the programming.

 

 

• Display window reads “THERMAL

 

SENSOR FAILURE”

Call Vitamix technical support.

 

 

• Machine stops in the middle

a. Plug the machine into its own

of its blend cycle and resets;

power supply.

display window reads

b. Make sure the machine is not running

“VITAMIX GENERAL PROGRAM”

on a long extension cord.

then “READY”

 

 

 

• If the machine has overheated:

Remove the container, shut the cover

The motor will stop and

door and press the Start/Stop button

the message “MOTOR HAS

and run the machine for two minutes.

OVERHEATED REMOVE  THE

When the motor is cool, “READY”

CONTAINER, THEN PRESS START,”

will appear in the display window.

will scroll across the display

 

window, while the words

 

“HOT SHUTDOWN” will remain

 

in the display window alerting

 

you of the problem.

 

 

 

If you cannot fix your machine with these suggestions, technical help is available by calling Vitamix® technical support at 800-886-5235. If you purchased your equipment outside the U.S.A., contact your local Vitamix Distributor or telephone the Vitamix International Division at +1.440.782.2450 or email international@vitamix.com for a distributor in your country. For online help, visit www.vitamix.com/foodservice.

23

Image 23
Contents Use and Care Manual Page Contents Do not use outdoors Important SafeguardsThree-prong adapters are not to be used in Canada Save These Safety InstructionsBlending Tips Instructions for using the Pre-Set Program ButtonsGENERAL INSTRUCTIONS Maintenance Tips Control Panel VITA-MIX Advance Program Custom Programmed Chip ProgrammingProgramming Pre-Set Buttons Programming your Machine with a Custom ChipImportant Notes Recipe Options Arranged by recipe number # and drink type Gradually ramps up to MED-HIGH 75% Containers Machine AssemblyCompact Cover Cover DoorTo replace the sound enclosure Back CoverTo remove the sound enclosure One-Piece Lid Figure B Two-Piece Lid Figure aBlade Assembly Removal Blade AssemblyPreparing the counter Area InstallationIn-Counter Machine Under hanging or wall On-Counter and In-Counter Blending StationCARING FOR YOUR MACHINE Important Notes Problems Possible Actions TroubleshootingCorrupt Data Conditions WarrantyMotor Base Page Quiet One Parts ListItems Sold Separately Vita-MixCorporation Commercial Division SpecificationsManual de uso y cuidado Page Programación Cuidado de la Máquina Solución de ProblemasContenido Precauciones importantes Instrucciones GeneralesPrecauciones Importantes En Canadá, no se deben usar adaptadores para tres clavijas Conserve estas instrucciones de seguridadConsejos para licuar Instrucciones GeneralesConsejos para el mantenimiento Panel DE Control VITA-MIX Advance Program Programa Avanzado VITA-MIX Por ejemplo Si quisiera programar el botón 1 con la receta ProgramaciónProgramación de los botones preestablecidos Programación de la máquina con un chip personalizado¡NOTAS Importantes Aumenta a velocidad Media 51% durante 10 segundos 50%, y finalmente a Alta 100% Vasos Montaje DE LA MáquinaCubierta compacta Puerta de la cubiertaPara volver a colocar la caja silenciadora Cubierta posteriorPara retirar la caja silenciadora Tapa de una pieza Figura B Tapa de dos piezas Figura aRetiro del conjunto de cuchillas Conjunto de cuchillasPreparación del área del mostrador InstalaciónMáquina empotrada Espacio por debajo de la máquina o pared Estación licuadora de sobremesa y empotradaCuidado DE LA Máquina ¡NOTAS Importantes Problemas Soluciones Solución DE ProblemasCorrupt Data Condiciones GarantíaBase de motor Page Núm Lista DE PiezasNúm Artículos que se venden por separado Vita-Mix Corporation Commercial Division EspecificacionesManuel d’utilisation et d’entretien Page Table DES Matières Ne pas utiliser pas ce produit à l’extérieur Précautions ImportantesAvertissement Conserver ces Instructions de sécuritéConseils de mélange Instructions GénéralesConseils d’entretien Programmes Préréglés Panneau DE ContrôleVITA-MIX Programme Advance Puce de Programmation Personnalisée ProgrammationProgrammation des boutons préréglés Programmation de votre appareil avec une puce personnaliséeRemarques Importantes Puis jusquà MED 60% pendant 14 secondes Jusquà MED 50%, puis jusquà High rapide 100% Bols Montage DE L’APPAREILCouvercle compact Porte du couverclePour remettre le boîtier anti-bruit Cache arrièrePour enlever le boîtier anti-bruit Couvercle en une partie Figure B Couvercle en deux parties Figure aDémontage de l’assemblage de lames Préparation du plan de travail InstallationAppareil intégré au plan de travail Rideau ou mur Installation électriqueDimension du modèle posé sur le plan de travail Dimension du modèle intégré au plan de travailEntretien DE Votre Appareil Remarques Importantes Dépannage Problèmes Solutions possiblesHas Overheated Remove Conditions GarantieSocle-moteur Page Liste DES Pièces Articles vendus séparément Spécifications