Shindaiwa LE2510/EVC manual 10/15-Hour Maintenance, Remove and clean or replace the spark plug

Page 12

Maintenance (continued)

10-Hour Maintenance

(more frequently in dusty conditions)

1.Remove the air cleaner cover by loos- ening the thumbscrews and lifting.

2.Remove and inspect the pre-filter. If the pre-filter is torn or otherwise damaged, replace it with a new one.

3.Clean the pre-filter with soap and water. Let dry before reinstalling.

4.Inspect the air filter element. If the element is damaged or distorted, replace it with a new one.

5.Tap filter gently on a hard surface to dislodge debris from element or use com- pressed air from the inside to blow debris out and away from the air filter element.

6.Install the air filter element, pre-filter and cover in the reverse order of removal.

10/15-Hour Maintenance

Remove and clean or replace the spark plug.

ŶClean the spark plug. Adjust electrode gap according to the values listed in the ”Specifications” section. If the spark plug must be replaced, use only the type rec- ommended in ”Specifications” or equiva- lent resistor type spark plug of the correct heat range.

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts.

50-hour Maintenance

Unscrew

Fasteners

Pre-Filter

Air Filter

Element

IMPORTANT!

 

CAUTION!

Direct the air stream at the inside face of

 

 

Never operate the unit if the air cleaner

the filter only!

 

 

 

assembly is damaged or missing!

 

 

 

 

0.6–0.7 mm

Clean the spark plug and check the gap at the electrode.

Remove and replace the fuel filter element

ŶBefore reinstalling the new fuel filter element, inspect the condition of all the fuel system components (fuel pick-up line, fuel return line, tank vent line, tank vent, fuel cap and fuel tank).

If damage, splitting or deterioration is noted, the unit should be removed from service until it can be inspected or repaired by a Shindaiwa-trained service technician.

Hooked Wire

)XHO¿OWHUHOHPHQW

5HPRYHDQGUHSODFHWKHIXHO¿OWHUHOHPHQ

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Lawn Edger Part Number 89307 Rev /09Contents IntroductionOperational and warning labels Safety Safety LabelsWork Safely Stay AlertProperly equipped operator Be aware of the working environmentProduct Description OperationAssembly Prior to assemblyAdjust Throttle Lever Free Play Mounting the cutting attachment shield and edger bladeMixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Adjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionUsing a hand-held edger Adjusting blade cutting depthTo adjust blade height OperationMaintenance Hour Maintenance 10/15-Hour MaintenanceRemove and clean or replace the spark plug filter only Assembly is damaged or missingGearcase lubrication Lubricate the Flexible ShaftD-shaped shim washer must be Inspect the Gearcase Protector139/150-Hour Maintenance Valve AdjustmentMaintenance after first 139-hours Long Term Storage0XIÁHU0DLQWHQDQFH Replacing the edger bladeTroubleshooting Guide Engine does not StartWhat To Check RemedyLOW Power Possible CauseIs the engine overheating? Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs RemarquesOrilladora DE Grama Introducción ContenidoDeclaraciones De Seguridad Etiquetas información de operaciónSeguridad Trabaje con cuidadoMantengase Alerta Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoEsté alerta del area de trabajo Descripción de producto Con seguridadEnsamblar Antes de ensamblarInstalación de la Caja de Engranaje Ajuste la holgura del aceleradorMezcla de Combustible Llenando el Tanque de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoOperación Utilizando el orillador de manoAjuste de la cuchilla Para ajustar la altura de cuchillaMantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 50 horas Mantenimiento cada 50 horas continuación Lubrique la caja de engranajesLubrique el Eje Flexible Inspeccione el Protector de la Caja de EngranajesMantenimiento Cada 139/150 Horas Ajuste de válvulasAlmacenamiento de Largo Plazo Mantenimiento de la silenciador Substituir la cuchillaRetire la malla y limpie con un cepillo de cerdas gruesas Guía Diagnóstico EL Motor no ArrancaQué revisar Posible causaBaja Potencia ¿Se sobrecalienta el motor?Limpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE Table des matières Mises en gardeÉtiquettes au fonctionnement et à la sécurité Sécurité Sécurité au travailDemeurer vigilant Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurTenir compte de l’environnement de travail Nomenclature Caractéristiques techniquesNe jamais effectuer des Assemblage Avant l’assemblagePare-débris et lame du coupe-bordures Réglage du jeu du levier d’accélérationMélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Contrôle de l’état de l’appareilUtilisation Consignes dutilisation du coupe-borduresRégler la profondeur de coupe de la lame Ajustemnet de la hauteur de la lameEntretien Entretien suite Entretien toutes les 10 heuresEntretien toutes les 10 15 heures Entretien toutes les 50 heuresEntretien toutes les 50 heures suite Lubrifier l’boîtier d’engrenageRemisage à long terme Réglage du jeu des soupapesEntretien aux 139 heures, puis Toutes les 150 heures ultérieuresRemplacement de la lame du coupe-bordure Entretien du pare-étincellesSolution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesLa présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantie

LE2510/EVC, 89307 specifications

The Shindaiwa 89307 LE2510/EVC is a versatile and powerful tool, designed for both professional landscapers and dedicated homeowners seeking efficiency and reliability in their outdoor maintenance tasks. This innovative product stands out with its robust engine, ergonomic design, and advanced features.

At the heart of the LE2510/EVC lies its reliable engine, designed to deliver optimal performance while ensuring low emissions. This model utilizes Shindaiwa’s advanced technology to provide a perfect balance between power and fuel efficiency, allowing users to complete their tasks without frequent refueling interruptions. The engine is known for its durability, ensuring longevity even with heavy use in demanding conditions.

One of the standout features of the Shindaiwa LE2510/EVC is its lightweight design, which substantially reduces user fatigue during extended periods of operation. Comfort is enhanced through its ergonomic handle, which is designed for an optimal grip, allowing for precise control and maneuverability. This is particularly beneficial for users who may be using the tool for extended hours or performing intricate tasks that require attention to detail.

Another significant characteristic is its versatility. The LE2510/EVC comes with interchangeable attachments, promoting a multi-functional approach to yard maintenance. Users can switch between various tools, enabling them to tackle tasks such as pruning, hedging, or trimming, thereby making it a cost-effective solution for all landscaping needs.

Shindaiwa also incorporates advanced technologies aimed at increasing productivity. The LE2510/EVC is equipped with a high-efficiency air filter system designed to ensure the engine operates at peak performance. This not only extends the operational life of the tool but also minimizes maintenance. The easy-start technology reduces the effort needed to start the machine, which is a major advantage for users facing difficult starting conditions.

In conclusion, the Shindaiwa 89307 LE2510/EVC is a remarkable garden tool that combines power, efficiency, and user comfort. Its advanced technologies and features make it an ideal choice for anyone looking to enhance their landscaping workflow, ensuring tasks are completed effectively and with minimal fuss. Whether for professional landscaping businesses or dedicated gardening enthusiasts, this model represents an investment in quality and performance.
Top Page Image Contents