Shindaiwa 89307 Gearcase lubrication, Lubricate the Flexible Shaft, D-shaped shim washer must be

Page 13

Maintenance (continued)

50-hour Maintenance (continued)

Gearcase lubrication

ŶRemove the shaft bolt, bolt guard, holder A, blade, holder B, and the out- put shaft collar. Press new grease into the gearcase until the old grease has been pushed out. Use only lithium-base grease.

Lubricate the Flexible Shaft

Lack of lubrication will cause rapid wear to the flexible shaft and also to the shaft tube liner, resulting in increased vibra- tion and greatly decreased service life. Remove and lubricate the flexible shaft as follows:

1.Loosen the gearcase clamp screw.

2.Remove the gearcase index screw.

3.Slide the gearcase and shield assembly from the shaft tube.

4.Pull the flexible shaft from the shaft tube assembly, and clean the shaft thor- oughly in solvent.

5.Inspect the shaft carefully, and replace if worn or damaged. If flexible shaft is worn and needs replacement, liner should also be replaced.

6.Coat the entire length of the shaft with a premium gearcase lube and reinstall the shaft in the shaft tube assembly.

7.Insert the flexible shaft into the female end of the gearcase pinion.

NOTE:

)RUH[WHQGHGVKDIWOLIHWKHÀH[LEOHFDEOH should be reversed end-for-end during the reinstallation process.

8.Reinstall the gearcase onto the outer tube in the reverse order of removal.

CAUTION!

The D-shaped shim washer must be

SRVLWLRQHGZLWKLWVÀDWHGJHWRZDUGWKH shaft tube.

Inspect the Gearcase Protector

The metal gearcase protector is installed to protect the gearcase flange from damage when working close to sidewalks or other abrasive surfaces, and should be routinely inspected for damage or excessive wear.

When replacing the protector, inspect to be sure that both of the protector mounting screws are firmly tightened and each screw is locked in place with a nut as shown.

 

 

 

New

 

 

 

Grease

Old

 

 

 

Grease

 

 

 

 

 

 

Shaft

 

 

 

Tube

 

Blade

 

Output Shaft Collar

Shaft Bolt

Bolt

Holder

Holder

 

Guard

A

B

Gearcase lubrication

 

 

 

 

 

Gearcase

 

 

 

Index Screw

 

Shaft tube

Gearcase

Flexible shaft

Flexible shaft lubrication

Outer

Gearcase

tube

 

D-shaped shim washer ÀDWVLGHWRZDUGWXEH

Reinstall the gearcase onto the outer tube

Nut

Mounting

Gearcase protector

screw

Inspect the gearcase protector

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Part Number 89307 Rev /09 Lawn EdgerIntroduction ContentsOperational and warning labels Safety Labels SafetyWork Safely Stay AlertBe aware of the working environment Properly equipped operatorOperation Product DescriptionPrior to assembly AssemblyAdjust Throttle Lever Free Play Mounting the cutting attachment shield and edger bladeFilling the fuel tank Mixing fuelExamples of 501 mixing quantities Minimize the Risk of FireStarting the Engine When the Engine StartsDepress and hold the throttle lock button Idle Speed Adjustment Adjusting Engine IdleStopping the Engine Checking Unit ConditionAdjusting blade cutting depth Using a hand-held edgerTo adjust blade height OperationMaintenance 10/15-Hour Maintenance Hour MaintenanceRemove and clean or replace the spark plug filter only Assembly is damaged or missingLubricate the Flexible Shaft Gearcase lubricationD-shaped shim washer must be Inspect the Gearcase ProtectorValve Adjustment 139/150-Hour MaintenanceMaintenance after first 139-hours Long Term StorageReplacing the edger blade 0XIÁHU0DLQWHQDQFHEngine does not Start Troubleshooting GuideWhat To Check RemedyPossible Cause LOW PowerIs the engine overheating? Engine is knockingWhat To Check Possible Cause Remedy Additional ProblemsEmission System Warranty Statement Remarques NOTAsOrilladora DE Grama Contenido IntroducciónDeclaraciones De Seguridad Etiquetas información de operaciónTrabaje con cuidado SeguridadMantengase Alerta Etiquetas de seguridadEl operario debidamente equipado Seguridad continuaciónEsté alerta del area de trabajo Con seguridad Descripción de productoAntes de ensamblar EnsamblarInstalación de la Caja de Engranaje Ajuste la holgura del aceleradorLlenando el Tanque de Combustible Mezcla de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosAl arrancar el motor Arranque del motorPosición O motor Apagado Deslice el interruptor de ignición a laUtilizando el orillador de mano OperaciónAjuste de la cuchilla Para ajustar la altura de cuchillaMantenimiento Mantenimiento cada 10 horas Mantenimiento continuaciónMantenimiento cada 50 horas Lubrique la caja de engranajes Mantenimiento cada 50 horas continuaciónLubrique el Eje Flexible Inspeccione el Protector de la Caja de EngranajesAjuste de válvulas Mantenimiento Cada 139/150 HorasAlmacenamiento de Largo Plazo Substituir la cuchilla Mantenimiento de la silenciadorRetire la malla y limpie con un cepillo de cerdas gruesas EL Motor no Arranca Guía DiagnósticoQué revisar Posible causa¿Se sobrecalienta el motor? Baja PotenciaLimpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Sus Derechos y Obligaciones de Garantía Esta garantía es administrada porCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE Mises en garde Table des matièresÉtiquettes au fonctionnement et à la sécurité Sécurité au travail SécuritéDemeurer vigilant Étiquettes de sécuritéÉquipement complet de l’utilisateur Sécurité suiteTenir compte de l’environnement de travail Caractéristiques techniques NomenclatureNe jamais effectuer des Avant l’assemblage AssemblagePare-débris et lame du coupe-bordures Réglage du jeu du levier d’accélérationRemplissage du réservoir à carburant Mélange de carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieLorsque le moteur démarre Démarrage du moteurArrêt du moteur Démarrage du moteur suiteRéglage du ralenti du moteur Contrôle de l’état de l’appareilConsignes dutilisation du coupe-bordures UtilisationRégler la profondeur de coupe de la lame Ajustemnet de la hauteur de la lameEntretien Entretien toutes les 10 heures Entretien suiteEntretien toutes les 10 15 heures Entretien toutes les 50 heuresLubrifier l’boîtier d’engrenage Entretien toutes les 50 heures suiteRéglage du jeu des soupapes Remisage à long termeEntretien aux 139 heures, puis Toutes les 150 heures ultérieuresEntretien du pare-étincelles Remplacement de la lame du coupe-bordureGuide de dépannage SolutionLE Moteur NE Démarre PAS Points à contrôlerPuissance Insuffisante Guide de dépannage suiteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes Points à contrôler Cause probable SolutionVos droits et obligations en vertu de la garantie La présente garantie est administrée parCouverture de la garantie des fabricants Couverture de la garantie

LE2510/EVC, 89307 specifications

The Shindaiwa 89307 LE2510/EVC is a versatile and powerful tool, designed for both professional landscapers and dedicated homeowners seeking efficiency and reliability in their outdoor maintenance tasks. This innovative product stands out with its robust engine, ergonomic design, and advanced features.

At the heart of the LE2510/EVC lies its reliable engine, designed to deliver optimal performance while ensuring low emissions. This model utilizes Shindaiwa’s advanced technology to provide a perfect balance between power and fuel efficiency, allowing users to complete their tasks without frequent refueling interruptions. The engine is known for its durability, ensuring longevity even with heavy use in demanding conditions.

One of the standout features of the Shindaiwa LE2510/EVC is its lightweight design, which substantially reduces user fatigue during extended periods of operation. Comfort is enhanced through its ergonomic handle, which is designed for an optimal grip, allowing for precise control and maneuverability. This is particularly beneficial for users who may be using the tool for extended hours or performing intricate tasks that require attention to detail.

Another significant characteristic is its versatility. The LE2510/EVC comes with interchangeable attachments, promoting a multi-functional approach to yard maintenance. Users can switch between various tools, enabling them to tackle tasks such as pruning, hedging, or trimming, thereby making it a cost-effective solution for all landscaping needs.

Shindaiwa also incorporates advanced technologies aimed at increasing productivity. The LE2510/EVC is equipped with a high-efficiency air filter system designed to ensure the engine operates at peak performance. This not only extends the operational life of the tool but also minimizes maintenance. The easy-start technology reduces the effort needed to start the machine, which is a major advantage for users facing difficult starting conditions.

In conclusion, the Shindaiwa 89307 LE2510/EVC is a remarkable garden tool that combines power, efficiency, and user comfort. Its advanced technologies and features make it an ideal choice for anyone looking to enhance their landscaping workflow, ensuring tasks are completed effectively and with minimal fuss. Whether for professional landscaping businesses or dedicated gardening enthusiasts, this model represents an investment in quality and performance.
Top Page Image Contents