Shindaiwa 89307, LE2510/EVC Stopping the Engine, Adjusting Engine Idle, Checking Unit Condition

Page 9

Starting the Engine (continued)

Starting A Flooded Engine

1.Disconnect the spark plug lead and use the spark plug wrench to remove the spark plug (turn counter clockwise to remove).

2.Slide the ignition switch to the “O” (STOP) position.

ŶIf the spark plug is fouled or soaked with fuel, clean the plug as necessary.

3.Open the choke and fully depress the throttle lever with your left hand, then pull the starter handle rapidly with your right hand to clear excess fuel from the combustion chamber.

4.Replace the spark plug and tighten it firmly with the spark plug wrench. If a torque wrench is available, torque the spark plug to the values recommended in the “Specifications” section.

5.Repeat the starting procedure for a warm engine.

6.If the engine still fails to start, refer to the troubleshooting section near the end of this manual.

Stopping the Engine

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition

switch to the “O” (Engine OFF) position.

OFF

Slide ignition to OFF

Adjusting Engine Idle

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the unit to your Shindaiwa dealer for inspection.

Checking Unit Condition

Idle Speed Adjustment

1.Place the unit on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

3.If a tachometer is available, adjust idle. Check Specifications page for correct idle speed

NOTE

Carburetor fuel mixture adjustments are preset at factory and cannot be serviced LQWKH¿HOG

Idle Adjusting

Screw

NEVER operate the unit with the cut- ting attachment shield or other protec- tive devices removed!

Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit with- out written approval from Shindaiwa, Inc.

ALWAYS make sure the cutting attach- ment is properly installed and firmly tightened before operation.

NEVER use a cracked or warped cutting attachment: replace it with a serviceable one.

ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attach- ment with new one and re-check.

ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment.

NEVER allow the engine to run at high RPM without a load. Doing so could dam- age the engine.

NEVER operate a unit with worn or dam- aged fasteners or attachment holders.

WARNING!

A cutting attachment shield or other protective device is no guarantee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS!

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Part Number 89307 Rev /09 Lawn EdgerContents IntroductionOperational and warning labels Safety Labels SafetyWork Safely Stay AlertBe aware of the working environment Properly equipped operatorOperation Product DescriptionPrior to assembly AssemblyAdjust Throttle Lever Free Play Mounting the cutting attachment shield and edger bladeFilling the fuel tank Mixing fuelExamples of 501 mixing quantities Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Idle Speed Adjustment Adjusting Engine IdleStopping the Engine Checking Unit ConditionAdjusting blade cutting depth Using a hand-held edgerTo adjust blade height OperationMaintenance 10/15-Hour Maintenance Hour MaintenanceRemove and clean or replace the spark plug filter only Assembly is damaged or missingLubricate the Flexible Shaft Gearcase lubricationD-shaped shim washer must be Inspect the Gearcase ProtectorValve Adjustment 139/150-Hour MaintenanceMaintenance after first 139-hours Long Term StorageReplacing the edger blade 0XIÁHU0DLQWHQDQFHEngine does not Start Troubleshooting GuideWhat To Check RemedyPossible Cause LOW PowerIs the engine overheating? Engine is knockingWhat To Check Possible Cause Remedy Additional ProblemsEmission System Warranty Statement Remarques NOTAsOrilladora DE Grama Contenido IntroducciónDeclaraciones De Seguridad Etiquetas información de operaciónTrabaje con cuidado SeguridadMantengase Alerta Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoEsté alerta del area de trabajo Con seguridad Descripción de productoAntes de ensamblar EnsamblarInstalación de la Caja de Engranaje Ajuste la holgura del aceleradorLlenando el Tanque de Combustible Mezcla de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosAl arrancar el motor Arranque del motorPosición O motor Apagado Deslice el interruptor de ignición a laUtilizando el orillador de mano OperaciónAjuste de la cuchilla Para ajustar la altura de cuchillaMantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 50 horas Lubrique la caja de engranajes Mantenimiento cada 50 horas continuaciónLubrique el Eje Flexible Inspeccione el Protector de la Caja de EngranajesMantenimiento Cada 139/150 Horas Ajuste de válvulasAlmacenamiento de Largo Plazo Mantenimiento de la silenciador Substituir la cuchillaRetire la malla y limpie con un cepillo de cerdas gruesas EL Motor no Arranca Guía DiagnósticoQué revisar Posible causa¿Se sobrecalienta el motor? Baja PotenciaLimpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Sus Derechos y Obligaciones de Garantía Esta garantía es administrada porCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE Table des matières Mises en gardeÉtiquettes au fonctionnement et à la sécurité Sécurité au travail SécuritéDemeurer vigilant Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurTenir compte de l’environnement de travail Nomenclature Caractéristiques techniquesNe jamais effectuer des Avant l’assemblage AssemblagePare-débris et lame du coupe-bordures Réglage du jeu du levier d’accélérationRemplissage du réservoir à carburant Mélange de carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieLorsque le moteur démarre Démarrage du moteurArrêt du moteur Démarrage du moteur suiteRéglage du ralenti du moteur Contrôle de l’état de l’appareilConsignes dutilisation du coupe-bordures UtilisationRégler la profondeur de coupe de la lame Ajustemnet de la hauteur de la lameEntretien Entretien toutes les 10 heures Entretien suiteEntretien toutes les 10 15 heures Entretien toutes les 50 heuresLubrifier l’boîtier d’engrenage Entretien toutes les 50 heures suiteRéglage du jeu des soupapes Remisage à long termeEntretien aux 139 heures, puis Toutes les 150 heures ultérieuresEntretien du pare-étincelles Remplacement de la lame du coupe-bordureGuide de dépannage SolutionLE Moteur NE Démarre PAS Points à contrôlerPuissance Insuffisante Guide de dépannage suiteLe moteur surchauffe-t-il ? Le moteur cogneAutres Problèmes Points à contrôler Cause probable SolutionVos droits et obligations en vertu de la garantie La présente garantie est administrée parCouverture de la garantie des fabricants Couverture de la garantie

LE2510/EVC, 89307 specifications

The Shindaiwa 89307 LE2510/EVC is a versatile and powerful tool, designed for both professional landscapers and dedicated homeowners seeking efficiency and reliability in their outdoor maintenance tasks. This innovative product stands out with its robust engine, ergonomic design, and advanced features.

At the heart of the LE2510/EVC lies its reliable engine, designed to deliver optimal performance while ensuring low emissions. This model utilizes Shindaiwa’s advanced technology to provide a perfect balance between power and fuel efficiency, allowing users to complete their tasks without frequent refueling interruptions. The engine is known for its durability, ensuring longevity even with heavy use in demanding conditions.

One of the standout features of the Shindaiwa LE2510/EVC is its lightweight design, which substantially reduces user fatigue during extended periods of operation. Comfort is enhanced through its ergonomic handle, which is designed for an optimal grip, allowing for precise control and maneuverability. This is particularly beneficial for users who may be using the tool for extended hours or performing intricate tasks that require attention to detail.

Another significant characteristic is its versatility. The LE2510/EVC comes with interchangeable attachments, promoting a multi-functional approach to yard maintenance. Users can switch between various tools, enabling them to tackle tasks such as pruning, hedging, or trimming, thereby making it a cost-effective solution for all landscaping needs.

Shindaiwa also incorporates advanced technologies aimed at increasing productivity. The LE2510/EVC is equipped with a high-efficiency air filter system designed to ensure the engine operates at peak performance. This not only extends the operational life of the tool but also minimizes maintenance. The easy-start technology reduces the effort needed to start the machine, which is a major advantage for users facing difficult starting conditions.

In conclusion, the Shindaiwa 89307 LE2510/EVC is a remarkable garden tool that combines power, efficiency, and user comfort. Its advanced technologies and features make it an ideal choice for anyone looking to enhance their landscaping workflow, ensuring tasks are completed effectively and with minimal fuss. Whether for professional landscaping businesses or dedicated gardening enthusiasts, this model represents an investment in quality and performance.
Top Page Image Contents