Shindaiwa LE2510/EVC, 89307 manual Assembly, Prior to assembly, Adjust Throttle Lever Free Play

Page 6

Assembly

Prior to assembly

Before assembling, make sure you have all

Ŷ Kit containing cutting attachment shield,

the components required for a complete unit.

mounting bracket and hardware, this

Carefully inspect all components for damage.

owner's/operator's manual, and a tool

Ŷ Outer Tube/Main Shaft Assembly

kit for routine maintenance.

Ŷ Cutting Attachment Shield

 

Ŷ Edger Blade

 

IMPORTANT!

The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation.

Mounting the cutting attachment shield and edger blade

1.Loosen gearcase clamp bolt.

2.Remove the gearcase index bolt.

3.Slide the gearcase oriented as shown onto the shaft tube insuring that the flex drive is engaged in the gearcase.

4.Reinstall the index bolt and tighten securely.

NOTE:

,WPD\EHQHFHVVDU\WRSXOOWKHÀH[FDEOH out from the shaft tube, engage into the gearcase and then slide the assembly onto the shaft tube.

5.Tighten the clamp bolt and torque to 52 – 69 inch-pounds.

Adjust Throttle Lever Free Play

The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, fol- low the procedures and illustrations that follow.

1.Loosen the air cleaner cover knob and remove the air cleaner cover.

2.Loosen the lock nut on the cable adjuster.

3.Turn the cable adjuster in or out as required to obtain proper free play 4-6 mm.

4.Tighten the locknut.

5.Reinstall the air cleaner cover.

Gearcase clamp bolt

Gearcase index bolt

Gearcase

Remove air cleaner cover

4-6 mm (3/16”-

1/4”)Throttle Free

Play

Throttle Lever Free Play

Shaft tube

Flex drive

Cable

Adjuster

Lock Nut

Adjust as required for 4-6 mm free play

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Lawn Edger Part Number 89307 Rev /09Contents IntroductionOperational and warning labels Work Safely SafetySafety Labels Stay AlertProperly equipped operator Be aware of the working environmentProduct Description OperationAdjust Throttle Lever Free Play AssemblyPrior to assembly Mounting the cutting attachment shield and edger bladeExamples of 501 mixing quantities Mixing fuelFilling the fuel tank Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Stopping the Engine Adjusting Engine IdleIdle Speed Adjustment Checking Unit ConditionTo adjust blade height Using a hand-held edgerAdjusting blade cutting depth OperationMaintenance Remove and clean or replace the spark plug Hour Maintenance10/15-Hour Maintenance filter only Assembly is damaged or missingD-shaped shim washer must be Gearcase lubricationLubricate the Flexible Shaft Inspect the Gearcase ProtectorMaintenance after first 139-hours 139/150-Hour MaintenanceValve Adjustment Long Term Storage0XIÁHU0DLQWHQDQFH Replacing the edger bladeWhat To Check Troubleshooting GuideEngine does not Start RemedyIs the engine overheating? LOW PowerPossible Cause Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs RemarquesOrilladora DE Grama Declaraciones De Seguridad IntroducciónContenido Etiquetas información de operaciónMantengase Alerta SeguridadTrabaje con cuidado Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoEsté alerta del area de trabajo Descripción de producto Con seguridadInstalación de la Caja de Engranaje EnsamblarAntes de ensamblar Ajuste la holgura del aceleradorEjemplos de cantidades de mezcla a proporción de Mezcla de CombustibleLlenando el Tanque de Combustible Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoAjuste de la cuchilla OperaciónUtilizando el orillador de mano Para ajustar la altura de cuchillaMantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 50 horas Lubrique el Eje Flexible Mantenimiento cada 50 horas continuaciónLubrique la caja de engranajes Inspeccione el Protector de la Caja de EngranajesMantenimiento Cada 139/150 Horas Ajuste de válvulasAlmacenamiento de Largo Plazo Mantenimiento de la silenciador Substituir la cuchillaRetire la malla y limpie con un cepillo de cerdas gruesas Qué revisar Guía DiagnósticoEL Motor no Arranca Posible causaLimpiar, reparar o sustituir en caso necesario Baja Potencia¿Se sobrecalienta el motor? El motor golpeaGuía Diagnóstico continuación Cobertura de la Garantía del Fabricante Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE Table des matières Mises en gardeÉtiquettes au fonctionnement et à la sécurité Demeurer vigilant SécuritéSécurité au travail Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurTenir compte de l’environnement de travail Nomenclature Caractéristiques techniquesNe jamais effectuer des Pare-débris et lame du coupe-bordures AssemblageAvant l’assemblage Réglage du jeu du levier d’accélérationExemples de quantités de mélange de carburant à Mélange de carburantRemplissage du réservoir à carburant Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Contrôle de l’état de l’appareilRégler la profondeur de coupe de la lame UtilisationConsignes dutilisation du coupe-bordures Ajustemnet de la hauteur de la lameEntretien Entretien toutes les 10 15 heures Entretien suiteEntretien toutes les 10 heures Entretien toutes les 50 heuresEntretien toutes les 50 heures suite Lubrifier l’boîtier d’engrenageEntretien aux 139 heures, puis Remisage à long termeRéglage du jeu des soupapes Toutes les 150 heures ultérieuresRemplacement de la lame du coupe-bordure Entretien du pare-étincellesLE Moteur NE Démarre PAS SolutionGuide de dépannage Points à contrôlerLe moteur surchauffe-t-il ? Guide de dépannage suitePuissance Insuffisante Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesCouverture de la garantie des fabricants La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie

LE2510/EVC, 89307 specifications

The Shindaiwa 89307 LE2510/EVC is a versatile and powerful tool, designed for both professional landscapers and dedicated homeowners seeking efficiency and reliability in their outdoor maintenance tasks. This innovative product stands out with its robust engine, ergonomic design, and advanced features.

At the heart of the LE2510/EVC lies its reliable engine, designed to deliver optimal performance while ensuring low emissions. This model utilizes Shindaiwa’s advanced technology to provide a perfect balance between power and fuel efficiency, allowing users to complete their tasks without frequent refueling interruptions. The engine is known for its durability, ensuring longevity even with heavy use in demanding conditions.

One of the standout features of the Shindaiwa LE2510/EVC is its lightweight design, which substantially reduces user fatigue during extended periods of operation. Comfort is enhanced through its ergonomic handle, which is designed for an optimal grip, allowing for precise control and maneuverability. This is particularly beneficial for users who may be using the tool for extended hours or performing intricate tasks that require attention to detail.

Another significant characteristic is its versatility. The LE2510/EVC comes with interchangeable attachments, promoting a multi-functional approach to yard maintenance. Users can switch between various tools, enabling them to tackle tasks such as pruning, hedging, or trimming, thereby making it a cost-effective solution for all landscaping needs.

Shindaiwa also incorporates advanced technologies aimed at increasing productivity. The LE2510/EVC is equipped with a high-efficiency air filter system designed to ensure the engine operates at peak performance. This not only extends the operational life of the tool but also minimizes maintenance. The easy-start technology reduces the effort needed to start the machine, which is a major advantage for users facing difficult starting conditions.

In conclusion, the Shindaiwa 89307 LE2510/EVC is a remarkable garden tool that combines power, efficiency, and user comfort. Its advanced technologies and features make it an ideal choice for anyone looking to enhance their landscaping workflow, ensuring tasks are completed effectively and with minimal fuss. Whether for professional landscaping businesses or dedicated gardening enthusiasts, this model represents an investment in quality and performance.
Top Page Image Contents