Shindaiwa DG150MI, DG250MI specifications Switch

Page 14

2.2.6.2 Pilot Lamp [DG250MI only]

Pilot Lamp indicates whether or not the generator is generating electricity, when the engine is driving.

5.2.7Switch

5.2.7.1Starter Switch

STOP

①When the switch is set to this position, all power will be off. The switch must be set to this position to remove the key.

RUN / PREHEAT

②The switch must be set to this position during operation. This position is also used during cold season, to preheat Glow Plug.

<Caution>

Do not leave the switch to this position, while the engine is stopped.

A battery discharges.

START

③This position will allow user to start the engine. When a user release the key, the setting will automatically return to <Operating / Preheating> position.

5.2.7.2 Panel Light Switch

This switch turns Panel Light to ON and OFF. The switch can only be used when the Start switch is in OPERATING position.

5.2.7.3 Emergency Stop button [DG250MI only]

This button is used to stop the engine in emergency. Keep pressing the button until the engine comes to complete halt.

<Caution>

Keep pressing the button until the engine stops in several seconds.

After the engine stops, be sure to return the starter switch to the STOP Position.

5.2.7.4 Circuit Breaker

By turning this circuit breaker switch to ON position, power will be transferred to the output terminal and to the load side. By turning to OFF position, it will shut down all power to the load side, preventing overload and short-circuit, and also breaking the earth leakage.

<Caution>

Do not use this breaker as the ON/OFF switch to the load.

The earth leakage breaking function is for 3-Phase circuit only, not 1-Phase Circuit.

- 14 -

Image 14

Contents Table of Contents DG150MI DG250MIIntroduction Electrical Shock Safety GuidelinesSuffocation from exhaust fume InjuriesBurns Injuries to eyes and skinFire Location of Warning labels Alternator Engine SpecificationsSpecification Matrix Control Panel Unit Name of GeneratorExternal view PartsAmbient Condition Control panel NameMonitor Display Water Temperature Monitoring Lamp for temperature HighEquipment Engine Oil Monitoring Lamp for oil pressure low Battery Charge Monitoring Lamp charge lamp Tachometer DG250MI only GaugesFluid Level Monitoring Lamp DG250MI only Hour MeterGenerator Gauges Water Temperature Gauge DG250MI onlyOil Pressure Gauge DG250MI only LampSwitch Voltage Regulator Fuel Line Changeover Valve 3-way valveVoltage Regulator and Throttle Handle Throttle HandleUsing fuel from external fuel tank Transport and InstallationUsing fuel from built-in fuel tank TransportationInstallation TransportationElectrical damages ConnectionSelecting Cable Connecting Cable Load Connection Terminal Plate 3-Phase / 1-phase 2.2 400 2 1-Phase Output Terminals & Receptacles2.1 200 Earth Leakage Relay and Grounding Grounding WorkOperation Check Earth leakage breaker relay has activatedElectrical Shock Injuries Initialization and pre-checkChecking Engine Oil Fire BurnsEngine Oil Capacity Viscosity and temperatureChecking Coolant / Water Checking Radiator / Adding water Checking Coolant reservoir tank / Adding coolantTension Checking Fan BeltCoolant Capacity ConditionChecking Fuel Checking Fuel, Engine Oil, and Water leakage Checking BatteryReplacing the battery Operation Initializing / preparationDuring Operation Post startup checkStopping the Generator Protection⑥ Features Adjustment During operationOverload Connecting to External Fuel TankProtection Feature List Maintenance Turn the lever for 3-way valve to B positionGenerator side Model Isuzu Part No Oil ChangeOil Filter Change Cleaning / Changing Air Filter Element Cleaning / Changing Fuel FilterModel Draining Water from Fuel TankChanging Coolant / Water Storage Procedures Long-term StorageTroubleshooting StackingSymptoms Possible Cause Corrective Actions Generator Wiring Diagram Page Page Page Engine Wiring Diagram