Shindaiwa DG150MI Stopping the Generator Protection⑥ Features, Adjustment During operation

Page 32

Turn the switch and the circuit breaker for the load equipment to OFF

Turn the circuit breaker for single-phase and 3-phase on the control panel to OFF position Loosen the locknut for the Speed Control knob

Press the Speed Control knob all the way in, while pressing Release Button, and let the engine idle at 1000min-1

Keep the engine idle (cooling down) for at least 3 minutes Turn the starter switch to STOP position

Add fuel to the fuel tank

Loosen the air extracting plug to remove the air out. Tighten the plug, ensuring all the air out. Turn the starter switch to <Operating/Preheating> position. It will take approximately 10 seconds to vacuum the air out.

9.2.2Adjustment During operation

Make minor adjustment to voltage and speed using the Speed Control Knob and Voltage Regulator, by monitoring Tachometer, frequency meter, and voltage meter

■Vacuuming the air out of the fuelling system in event of no fuel Refer to the <User’s manual for Engine> separately.

✳This generator is equipped with automatic vacuuming air feature. Thus if the engine stops due to running out of fuel, follow the next steps to vacuum the air out.

<Caution> ③

①

Ensure that all the air is completely extracted from fuel line, by pushing the speed control knob all the way out and start the engine.

②

In the case air is in the fuel line, the engine speed is unstable, and proceed with the vacuuming steps again.

9.3 Stopping the Generator

①

②

③

9.4 Protection⑥ Features

④

⑤

This generator is equipped with automatic shutdown feature and display of the location of alarm, in event of any alarm situation. In event of the automatic shutdown or alarm lamp flashing, turn off the engine and investigate the alarm.

- 32 -

Image 32

Contents Table of Contents DG150MI DG250MIIntroduction Safety Guidelines Suffocation from exhaust fumeElectrical Shock InjuriesBurns Injuries to eyes and skinFire Location of Warning labels Specifications Specification MatrixAlternator Engine Control Panel Unit Name of GeneratorExternal view PartsAmbient Condition Control panel NameMonitor Display Water Temperature Monitoring Lamp for temperature HighEquipment Engine Oil Monitoring Lamp for oil pressure low Battery Charge Monitoring Lamp charge lamp Gauges Fluid Level Monitoring Lamp DG250MI onlyTachometer DG250MI only Hour MeterWater Temperature Gauge DG250MI only Oil Pressure Gauge DG250MI onlyGenerator Gauges LampSwitch Fuel Line Changeover Valve 3-way valve Voltage Regulator and Throttle HandleVoltage Regulator Throttle HandleTransport and Installation Using fuel from built-in fuel tankUsing fuel from external fuel tank TransportationInstallation TransportationElectrical damages ConnectionSelecting Cable Connecting Cable Load Connection Terminal Plate 3-Phase / 1-phase 2.2 400 2 1-Phase Output Terminals & Receptacles2.1 200 Earth Leakage Relay and Grounding Grounding WorkOperation Check Earth leakage breaker relay has activatedInitialization and pre-check Checking Engine OilElectrical Shock Injuries Fire BurnsEngine Oil Capacity Viscosity and temperatureChecking Coolant / Water Checking Radiator / Adding water Checking Coolant reservoir tank / Adding coolantChecking Fan Belt Coolant CapacityTension ConditionChecking Fuel Checking Fuel, Engine Oil, and Water leakage Checking BatteryReplacing the battery Operation Initializing / preparationDuring Operation Post startup checkStopping the Generator Protection⑥ Features Adjustment During operationOverload Connecting to External Fuel TankProtection Feature List Maintenance Turn the lever for 3-way valve to B positionGenerator side Model Isuzu Part No Oil ChangeOil Filter Change Cleaning / Changing Air Filter Element Cleaning / Changing Fuel FilterModel Draining Water from Fuel TankChanging Coolant / Water Storage Procedures Long-term StorageTroubleshooting StackingSymptoms Possible Cause Corrective Actions Generator Wiring Diagram Page Page Page Engine Wiring Diagram