Shindaiwa DG250MI, DG150MI Checking Fuel, Engine Oil, and Water leakage, Checking Battery

Page 29
Check the fluid level. If the level is near or lower than the MIN level, add distilled water until the fluid level reaches the MAX limit.
Make sure that the battery cables are firmly secured to the posts. Tighten the clamps if necessary.

8.5 Checking Fuel, Engine Oil, and Water leakage

! Caution

:Fire

Do not use this equipment when a leak is found. Repair the equipment before use.

Be sure to check for any fuel leak at the hose connection, and oil and coolant leak by opening side doors.

8.6 Checking Battery

! Caution

:Injuries to eyes and skin

Battery fluid contains diluted sulfuric acid. Avoid contact with eyes, skin or on clothing.

If the acid comes in contact, especially with eyes, flush with a lot of water, and contact your physician immediately.

! Caution

:Fire

Battery may emit some combustible gas, so keep it away from fire and sparks.

<Caution>

Check the hydrometer of the battery fluid. If it falls below 1.23,

the battery requires recharging. Please call our authorized distributor or our engineering section.

Replacing the battery

Remove the clamp and cable from negative (-)post from the

 

battery. (always remove negative side first)

 

Remove the hold-down clamp from the battery.

 

Remove the clamp and cable from positive (+) post from the

 

battery.

 

Remove the battery from the seat

Reinstall the new battery in the reverse order (always install the

cable to the positive (+) post of the new battery first.

<Caution>

Make sure that the removed cable does not come in contact with the battery post.

- 29 -

Image 29
Contents DG150MI DG250MI Table of ContentsIntroduction Suffocation from exhaust fume Safety GuidelinesElectrical Shock InjuriesBurns Injuries to eyes and skinFire Location of Warning labels Specification Matrix SpecificationsAlternator Engine Control Panel Unit Name of GeneratorExternal view PartsAmbient Condition Name Control panelMonitor Display Water Temperature Monitoring Lamp for temperature HighEquipment Engine Oil Monitoring Lamp for oil pressure low Battery Charge Monitoring Lamp charge lamp Fluid Level Monitoring Lamp DG250MI only GaugesTachometer DG250MI only Hour MeterOil Pressure Gauge DG250MI only Water Temperature Gauge DG250MI onlyGenerator Gauges LampSwitch Voltage Regulator and Throttle Handle Fuel Line Changeover Valve 3-way valveVoltage Regulator Throttle HandleUsing fuel from built-in fuel tank Transport and InstallationUsing fuel from external fuel tank TransportationTransportation InstallationElectrical damages ConnectionSelecting Cable Connecting Cable Load Connection Terminal Plate 3-Phase / 1-phase 2.2 400 2 1-Phase Output Terminals & Receptacles2.1 200 Grounding Work Earth Leakage Relay and GroundingEarth leakage breaker relay has activated Operation CheckChecking Engine Oil Initialization and pre-checkElectrical Shock Injuries Fire BurnsEngine Oil Capacity Viscosity and temperatureChecking Coolant / Water Checking Coolant reservoir tank / Adding coolant Checking Radiator / Adding waterCoolant Capacity Checking Fan BeltTension ConditionChecking Fuel Checking Fuel, Engine Oil, and Water leakage Checking BatteryReplacing the battery Initializing / preparation OperationPost startup check During OperationAdjustment During operation Stopping the Generator Protection⑥ FeaturesOverload Connecting to External Fuel TankProtection Feature List Turn the lever for 3-way valve to B position MaintenanceGenerator side Model Isuzu Part No Oil ChangeOil Filter Change Cleaning / Changing Fuel Filter Cleaning / Changing Air Filter ElementModel Draining Water from Fuel TankChanging Coolant / Water Long-term Storage Storage ProceduresStacking TroubleshootingSymptoms Possible Cause Corrective Actions Generator Wiring Diagram Page Page Page Engine Wiring Diagram