Husqvarna Pro 18 manual Transport

Page 11

SAFETY INSTRUCTIONS

Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas.

Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

Never make adjustments with the engine running.

The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer.

The blades are sharp and can cause cuts. Wrap the blades or wear protective gloves when handling them.

Check regularly that the parking brake works. Adjust and maintain as required.

Never run the machine in an enclosed area.

The mulching unit should only be used where better quality mowing is required and in known areas.

Reduce the risk of fire by removing grass, leaves and other debris that may have fastened on the machine. Allow the machine to cool before putting it in storage.

Transport

The machine is heavy and can cause serious crush injuries. Be especially careful when it is loaded in or out of a car or on and off of a trailer.

Use an approved trailer to transport the ma- chine. Activate the parking brake, shutoff the fuel supply and secure the machine using approved fasteners, such as tension belts, chains or ropes when transporting.

Regularly clean grass, leaves and other debris from the machine.

Check and observe local road traffic regulations before transporting or driving the machine on roads.

IMPORTANT INFORMATION

The parking brake is not sufficient to lock the machine during transport. Ensure you secure the machine firmly to the transporting vehicle. Reverse the machine on to the transporting vehicle to prevent it from overturning.

10 – English

Image 11
Contents Rider Pro 15 Rider Pro Contents Towing InstructionDear customer Driving and transport on public roadsSerial number Safety InstructionsGood service Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Speed limiter PresentationPresentation Location of the controls Pro Cutting unitPresentation Chronometer Presentation PROThrottle control Choke leverLift lever for cutting unit Lever for adjustment of the cutting heightFuelling Parking brakeSeat Throttle control Lift lever for cutting unit Lights and power outlet Release lever DrivingCutting tips Starting the engine Driving PROBefore starting Driving PRO Driving the machine Stopping the engine Before starting Driving PRO Driving the machine Stopping the engine Year MaintenanceMaintenance schedule Year 100 300 Transmission cover Removing of the machine hoodsEngine cover Pro Front coverLeft-hand fender Pro Right-hand fender ProChecking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the parking brakeChecking and adjustment of the throttle wire Checking and adjusting the choke wireReplacement of the fuel filter Pro Check the transmission’s air intake Cleaning the pulse air filterChecking of the fuel pump’s air filter Muffler air intakeReplacing the air filter Pro Maintenance Checking the engine’s cooling air intake Cleaning the engine and mufflerFitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Replacing the light bulbs, Pro Checking the tyre pressure FusesObserve caution to avoid trapping your hand Fitting the cutting unitRemoving the cutting unit Installing BioClipCutting Height Checking and adjusting the cutting unit’s ground pressureReplacing the cutting unit belt Adjusting the parallelism of the cutting unitBelt replacement on BioClip Checking the cutting unit’s parallelismBelt change on Combi Maintenance Placing in service position Service position for the cutting unitMaintenance Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin BioClip 90, CombiLubrication Lubrication chartLubrication General Lubricating wiresPedal mechanism in frame tunnel Pro Driver’s seat Chains in frame tunnelTriangular link and joints Belt tensioner Throttle and choke wires, lever bearingsEngine oil Changing the engine oil Gear leverTransmission Parking brake wireTransmission oil level Hydraulic oil filter, change Replacing the oil filterProblem Procedure Trouble Shooting ScheduleCover ServiceStorage Winter storageBL = Wiring Diagram PROBR = Technical Data Combi Cutting unit BioClipSide ejector Rear ejector EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´z+H.6¶6*¨ Page 2003W07 114 01