Husqvarna Pro 18 manual Replacing the oil filter, Hydraulic oil filter, change

Page 65

LUBRICATION

13. Replacing the oil filter

WARNING!

The engine oil may be very hot if it is drained immediately after stopping the engine. Let the engine cool down for a while first.

1.Open the engine cover.

2.Drain the engine oil as described under ”Changing the engine oil”.

3.Remove the oil filter. If necessary use a filter spanner.

4.Coat the seal on the new filter with clean, fresh engine oil.

5.Tighten the filter by hand until you feel it make contact, then tighten a further 3/4 turn.

6.Run the engine until it is hot, then check that there is no leakage from the oil filter seal.

7.Check the engine oil level and top up if necessary. The oil filter holds 0.2 litres of oil.

IMPORTANT INFORMATION

Used engine or transmission oil is health- impairing and must not be disposed of in the ground or in nature.

Replaced filters must be handed in to the workshop or other allotted place for disposal.

Avoid skin contact; wash with soap and water in case of spills.

14.Hydraulic oil filter, change

1.Remove the oil filter. If necessary, use a filter remover.

2.Wipe new, clean engine oil onto the seal for the new filter.

3.Fit the filter by hand so it just touches + 3/4 turn.

4.Remove the transmission cover and fill the transmission’s oil tank, about 0.3 l oil. See ”11. Transmission oil level. Be observant when running the engine as described below and fill so that the tank is not emptied.

5.Run the engine warm, manipulate the servo steering, and then check that there are no leaks around the oil filter seal.

6.Check the oil level in the transmission, top up if necessary. The oil filter holds 0.3 litres of oil.

7.Replace the transmission cover.

Pro 15

Pro 18

64 – English

Image 65

Contents Rider Pro 15 Rider Pro Contents Dear customer InstructionDriving and transport on public roads TowingSerial number Safety InstructionsGood service Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Speed limiter PresentationPresentation Location of the controls Pro Cutting unitPresentation Throttle control Presentation PROChoke lever ChronometerLift lever for cutting unit Lever for adjustment of the cutting heightFuelling Parking brakeSeat Throttle control Lift lever for cutting unit Lights and power outlet Release lever DrivingCutting tips Starting the engine Driving PROBefore starting Driving PRO Driving the machine Stopping the engine Before starting Driving PRO Driving the machine Stopping the engine Year MaintenanceMaintenance schedule Year 100 300 Engine cover Pro Removing of the machine hoodsFront cover Transmission coverLeft-hand fender Pro Right-hand fender ProChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Adjusting the parking brakeChecking and adjusting the choke wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Pro Checking of the fuel pump’s air filter Cleaning the pulse air filterMuffler air intake Check the transmission’s air intakeReplacing the air filter Pro Maintenance Checking the engine’s cooling air intake Cleaning the engine and mufflerFitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Replacing the light bulbs, Pro Checking the tyre pressure FusesObserve caution to avoid trapping your hand Fitting the cutting unitRemoving the cutting unit Installing BioClipCutting Height Checking and adjusting the cutting unit’s ground pressureBelt replacement on BioClip Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Placing in service position Service position for the cutting unitMaintenance Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin BioClip 90, CombiLubrication Lubrication chartLubrication General Lubricating wiresPedal mechanism in frame tunnel Pro Driver’s seat Chains in frame tunnelTriangular link and joints Belt tensioner Throttle and choke wires, lever bearingsEngine oil Changing the engine oil Gear leverTransmission Parking brake wireTransmission oil level Hydraulic oil filter, change Replacing the oil filterProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverBL = Wiring Diagram PROBR = Technical Data Combi Cutting unit BioClipSide ejector Rear ejector EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done ServicejournalPre-delivery service Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´z+H.6¶6*¨ Page 2003W07 114 01