Husqvarna Pro 18 manual Servicejournal, Pre-delivery service, Work done

Page 73

SERVICEJOURNAL

Work done

Date, mileage, stamp, sign

Pre-delivery service

1. Top up battery with acid and recharge for four hours.

2. Fit steering wheel, seat and any optional equipment.

3. Fit cutting unit.

4. Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12–15 kg, or set to maximum lift if brush is to be fitted).

Adjust cutting unit so that rear edge is about 2–4 mm higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5

mmabove the frame of the unit at the lowest cutting height.

5.Check that the oil levels in the engine and transmission are

correct.

6. Check and adjust tyre pressure (60 kPa, 0.6 bar).
7. Connect battery.
8. Fill with fuel and start engine.
9. Check that machine does not move in neutral.
10. Check:
Forward drive.
Reverse drive.
Operation of blades.
Seat safety switch.
Lift lever safety switch.
Safety switch for the hydrostat pedals.
11. Check engine revs 3,000 ±75 rpm.
12. Tell customer about:	Pre-delivery service carried out.
Need and benefits of following the service schedule.	No outstanding problems.
Need and benefits of following the service schedule.
Need and benefits of having machine serviced every 300	Certified:
Need and benefits of having machine serviced every 300
hours.
Servicing and the influence of this journal on the second-hand
value of the machine.
Range of applications for BioClip.
13. Complete proof of sale, etc.

After first 8 hours 1. Change engine oil.

72 – English

Image 73

Contents Rider Pro 15 Rider Pro Contents Dear customer InstructionDriving and transport on public roads TowingGood service Safety InstructionsSerial number Read the instructions Explanation of SymbolsGeneral use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationSpeed limiter Location of the controls Pro Cutting unitPresentation Throttle control Presentation PROChoke lever ChronometerLift lever for cutting unit Lever for adjustment of the cutting heightSeat Parking brakeFuelling Throttle control Lift lever for cutting unit Lights and power outlet Cutting tips DrivingRelease lever Before starting Driving PROStarting the engine Driving PRO Driving the machine Stopping the engine Before starting Driving PRO Driving the machine Stopping the engine Maintenance schedule MaintenanceYear Year 100 300 Engine cover Pro Removing of the machine hoodsFront cover Transmission coverLeft-hand fender Pro Right-hand fender ProChecking and adjustment of the steering wires Checking and adjustment of the throttle wire Adjusting the parking brakeChecking and adjusting the choke wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Pro Checking of the fuel pump’s air filter Cleaning the pulse air filterMuffler air intake Check the transmission’s air intakeReplacing the air filter Pro Maintenance Checking the engine’s cooling air intake Cleaning the engine and mufflerProcedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Replacing the light bulbs, Pro Checking the tyre pressure FusesObserve caution to avoid trapping your hand Fitting the cutting unitRemoving the cutting unit Installing BioClipCutting Height Checking and adjusting the cutting unit’s ground pressureBelt replacement on BioClip Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Placing in service position Service position for the cutting unitMaintenance Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin BioClip 90, CombiLubrication Lubrication chartLubrication General Lubricating wiresPedal mechanism in frame tunnel Pro Triangular link and joints Chains in frame tunnelDriver’s seat Belt tensioner Throttle and choke wires, lever bearingsEngine oil Changing the engine oil Gear leverTransmission oil level Parking brake wireTransmission Hydraulic oil filter, change Replacing the oil filterProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverBL = Wiring Diagram PROBR = Technical Data Side ejector Rear ejector Cutting unit BioClipCombi EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service ServicejournalWork done Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´z+H.6¶6*¨ Page 2003W07 114 01