Husqvarna Pro 18 manual Driving the machine

Page 24

DRIVING PRO 15

Driving the machine

1. Release the parking brake by pressing the brake pedal.

2.Carefully press down one of the pedals until the required speed is obtained.

To drive forward press down pedal (1), or to reverse pedal (2).

WARNING!

Make sure that branches do not obstruct the pedals when mowing under bushes, otherwise you may lose control.

2

1

3.Push in the lock button on the lift lever and lower down the cutting unit.

IMPORTANT INFORMATION

The life span of the drive belts is increased significantly if the engine runs at a low speed when the blades are engaged. Therefore apply full throttle first when the cutting unit has been moved to the mowing position.

4.Select the required cutting height (1–9) with the cutting height lever.

It is important that the air pressure in both front wheels is equal, 60 kPa / 8.5 PSI, to produce an even cutting height.

English – 23

Image 24

Contents Rider Pro 15 Rider Pro Contents Instruction Dear customerDriving and transport on public roads TowingSafety Instructions Good serviceSerial number Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationSpeed limiter Cutting unit Location of the controls ProPresentation Presentation PRO Throttle controlChoke lever ChronometerLever for adjustment of the cutting height Lift lever for cutting unitParking brake SeatFuelling Throttle control Lift lever for cutting unit Lights and power outlet Driving Cutting tipsRelease lever Driving PRO Before startingStarting the engine Driving PRO Driving the machine Stopping the engine Before starting Driving PRO Driving the machine Stopping the engine Maintenance Maintenance scheduleYear Year 100 300 Removing of the machine hoods Engine cover ProFront cover Transmission coverRight-hand fender Pro Left-hand fender ProChecking and adjustment of the steering wires Adjusting the parking brake Checking and adjustment of the throttle wireChecking and adjusting the choke wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Pro Cleaning the pulse air filter Checking of the fuel pump’s air filterMuffler air intake Check the transmission’s air intakeReplacing the air filter Pro Maintenance Cleaning the engine and muffler Checking the engine’s cooling air intakeCheck the level of the battery acid Procedures on contact with acidFitting the wrong spark plug type can damage the engine Inspecting the safety system Replacing the light bulbs, Pro Fuses Checking the tyre pressureFitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Removing the cutting unitChecking and adjusting the cutting unit’s ground pressure Cutting HeightAdjusting the parallelism of the cutting unit Belt replacement on BioClipChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Service position for the cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip 90, Combi Removal of BioClip plug CombiLubrication chart LubricationLubrication Lubricating wires GeneralPedal mechanism in frame tunnel Pro Chains in frame tunnel Triangular link and jointsDriver’s seat Throttle and choke wires, lever bearings Belt tensionerEngine oil Gear lever Changing the engine oilParking brake wire Transmission oil levelTransmission Replacing the oil filter Hydraulic oil filter, changeTrouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverWiring Diagram PRO BL =BR = Technical Data Cutting unit BioClip Side ejector Rear ejectorCombi EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Pre-delivery serviceWork done Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´z+H.6¶6*¨ Page 114 01 2003W07