Husqvarna Pro 18 Removing of the machine hoods, Engine cover Pro, Front cover, Transmission cover

Page 32

MAINTENANCE

Removing of the machine hoods

The engine becomes accessible for service when the engine cover is opened.

Engine cover Pro 15

1. Pull the seat forward to its foremost position.

2. Tip the seat forward.

3. Loosen the rubber strap.

4. Open the engine cover backwards.

Engine cover Pro 18

1.Pull the seat forward to its foremost position.

2.Fold up the seat.

3. Turn the cover lock on the top of the engine cover anti-clockwise a 1/4 turn.

4. Open the engine cover forwards. If necessary the engine cover can be lifted off by removing the hinge pins.

Front cover

Release the clip on the front hood and lift off the fender.

Transmission cover

Undo the two screws (one on each side) and lift off the transmission cover.

English – 31

Image 32

Contents Rider Pro 15 Rider Pro Contents Instruction Dear customerDriving and transport on public roads TowingSerial number Safety InstructionsGood service Explanation of Symbols Read the instructionsSafety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Speed limiter PresentationPresentation Cutting unit Location of the controls ProPresentation Presentation PRO Throttle controlChoke lever ChronometerLever for adjustment of the cutting height Lift lever for cutting unitFuelling Parking brakeSeat Throttle control Lift lever for cutting unit Lights and power outlet Release lever DrivingCutting tips Starting the engine Driving PROBefore starting Driving PRO Driving the machine Stopping the engine Before starting Driving PRO Driving the machine Stopping the engine Year MaintenanceMaintenance schedule Year 100 300 Removing of the machine hoods Engine cover ProFront cover Transmission coverRight-hand fender Pro Left-hand fender ProChecking and adjustment of the steering wires Adjusting the parking brake Checking and adjustment of the throttle wireChecking and adjusting the choke wire Poorly adjusted brakes can result in reduced braking powerReplacement of the fuel filter Pro Cleaning the pulse air filter Checking of the fuel pump’s air filterMuffler air intake Check the transmission’s air intakeReplacing the air filter Pro Maintenance Cleaning the engine and muffler Checking the engine’s cooling air intakeFitting the wrong spark plug type can damage the engine Check the level of the battery acidProcedures on contact with acid Inspecting the safety system Replacing the light bulbs, Pro Fuses Checking the tyre pressureFitting the cutting unit Observe caution to avoid trapping your handInstalling BioClip Removing the cutting unitChecking and adjusting the cutting unit’s ground pressure Cutting HeightAdjusting the parallelism of the cutting unit Belt replacement on BioClipChecking the cutting unit’s parallelism Replacing the cutting unit beltBelt change on Combi Maintenance Service position for the cutting unit Placing in service positionMaintenance Restoring from service position Checking the blades Replacing the break-pin BioClip 90, Combi Removal of BioClip plug CombiLubrication chart LubricationLubrication Lubricating wires GeneralPedal mechanism in frame tunnel Pro Driver’s seat Chains in frame tunnelTriangular link and joints Throttle and choke wires, lever bearings Belt tensionerEngine oil Gear lever Changing the engine oilTransmission Parking brake wireTransmission oil level Replacing the oil filter Hydraulic oil filter, changeTrouble Shooting Schedule Problem ProcedureService StorageWinter storage CoverWiring Diagram PRO BL =BR = Technical Data Combi Cutting unit BioClipSide ejector Rear ejector EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeWork done ServicejournalPre-delivery service Hour service Servicejournal 100/200 hour service Servicejournal At least once a season Work done Date, mileage, stamp, sign Servicejournal ´z+H.6¶6*¨ Page 114 01 2003W07