Husqvarna GT48XLSi To Replace Mower Blade Drive Belt, To Check Brake, Front Wheel TOE-IN/CAMBER

Page 24

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER BLADE DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 41)

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Remove mandrel covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

•With a 3/8" breaker bar and using the square opening in the idler arm, shift the arm counterclockwise () to relieve the tension on the belt.

•Carefully roll the belt over the top of the cutter housing

pulleys.

IDLER ARM

Fig. 41

•Remove the belt from around the electric clutch on the engine shaft.

MOWER DRIVE BELT INSTALLATION (See Fig. 42 & 43)

NOTE: For ease in installing the deck belt, refer to the routing decal on the cutting deck.

•Place the belt around all the pulleys except the idler pulley.

•With a 3/8" breaker bar, shift the idler arm counter- clockwise (). When there is enough slack, slip the belt onto the idler pulley.

BELT ROUTING

ENGINE

IDLER

BLADE BELT

PULLEY

 

Fig. 42

•Double check belt routing to make sure it matches the routing decal, and that the belt does not have any twist. Correct if needed.

•Adjust belt tension by turning the eyebolt until spring is extended to a length of 5.1" (13 cm).

•Belt tension should be set to 30 Ft. Lbs/40 Nm.

•Replace mandrel covers on both mandrel housings and secure with fasteners.

SPRING

EYEBOLT

NUT

Fig. 43

TO CHECK BRAKE

If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s Manual Manual de Operario English/SpanishSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To Adjust Mower Cutting Height See Fig To USE Throttle Control D SeeTo Move Forward and Backward See Fig To USE Cruise Control J See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Stop Mower Blades Reverse Operation System ROS See FigBattery INDICATOR/CHARGING Plug See Fig Battery Indicator Button See FigTo Transport See Fig Resetting Ignition System Passcode See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineSmartswitch Warning Lights See Fig To Start EnginePRE-START StartingMowing Tips Purge TransmissionHour Meter Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning Deck Washout Port See Fig Service and Adjustments To Install Mower SeeTo Remove Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower Mower, or, counterclockwise Loosen to lower Front mowerTo Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER PulleysBelt Installation To Replace Motion Drive Belt See FigTo Remove Wheel See Fig Belt RemovalTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Replace LED Headlight Interlocks and RelaysSmartswitch Ignition System Lights See Fig To Remove Hood and Grill Assembly See FigREMOVAL/REPLACEMENT To Adjust Throttle Control CableStorage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionTo run when oper Battery will notFires when turn Engine continuesConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXReglas DE Seguridad AdvertenciaFuncionamiento General II. Funcionamiento EN PendientesIII. Niños IV. RemolqueServicio Manipulación Segura DE LA GasolinaTabla DE Materias Especificaciones DEL ProductoResponsabilidades DEL Cliente Piezas SIN Montar MontajeHerramientas Necesarias Para EL Montaje Para Remover EL Tractor DE LA Caja DE CartónRevisión DE LA Presión DE LAS Llantas Revisión DE LA Nivelación DEL ConjuntoRevisión DE LA Posición Adecuada DE Todas LAS Correas Revisión DEL Sistema DE FrenosOperación Familiaricese CON SU Tractor Amperímetro Indica la carga + o la descarga de la bateríaComo Usar SU Tractor Para Ajustar EL Freno DE Estacionamiento Vea FigParada Vea Fig Cómo Usar EL Control DEL Cierre Diferencial Para Ajustar LAS Ruedas Calibradoras Vea Fig Para Operar LA SegadoraPara Parar LAS Cuchillas DE LA Segadora Sistema DE Operación EN Reversa ROS Vea FigPara Transportar Vea Fig RemolquedecarretillasootrosaccesoriosFaros Delanteros Testigo DE BATERÍA/CONECTOR DE Carga Vea FigAntesde Hacerarrancar EL Motor Revise EL Nivel DE Aceite DEL MotorAgregue Gasolina Para Operar DE LA Valvula DE Gasolina DE Reserva Vea FigArranque DEL Motor Consejos Para Segar Purgar LA TransmisiónContador Horario Mantenimiento Recomendaciones GeneralesTabla DE Lubricación Antes DE Cada USOTractor Operación DEL FrenoCuidado DE LA Cuchilla LlantasMotor Limpieza Puerto DE Lavado DE LA Cubierta Vea Fig Servicio Y Ajustes Instale LA Segadora VeaBarra Antibalanceo S Instale la correa pasándola por encima de la polea del motor Para Nivelar LA Segadora Controlar Y Ajustar EL Freno Impresión / Inclinación DE LAS Ruedas DEL- AnterasPara Cambiar LA Correa DE Impulsión DE Movimiento Vea Fig Desmontaje DE LA CorreaMontaje DE LA Correa Para Remover LAS Ruedas Vea FigPara Hacer Arrancar EL Motor CON UNA BAT- Ería Baja Vea Fig Reemplazar LA Bateria Vea FigSustitución DEL Faro LED Entrecierre Y ReléLuces DEL Sistema DE Arranque Smartswitch Vea Fig TransmisiónPara Remover EL Conjunto DEL Capota Y DEL Enrejado Vea Fig REMOCIÓN/REEMPLAZO DE LA TransmisiónAlmacenamiento OtrosSistema DE Combustible Aceite DEL MotorIdentificación DE Problemas Problema Causa CorrecciónFuncionando cuando Pendiente Productos de consumo equipados con ruedas Garantía limitada Cómo Obtener Servicio Transmisión** Giro cero EZ y MZ Moldeada, no reforzada Service NOTES/ Aviso Service NOTES/ Aviso 11/15/13 AP
Top Page Image Contents