Husqvarna GT48XLSi Transmission, Smartswitch Ignition System Lights See Fig, Removal/Replacement

Page 27

SERVICE AND ADJUSTMENTS

SMARTSWITCH IGNITION SYSTEM LIGHTS (See Fig. 49)

The SmartSwitch System is equipped with courtesy lights that are used to indicate system functions or faults.

FUNCTIONS

•The SmartSwitch Ignition (SSI) Button (F) will blink blue while waiting for the correct passcode to be entered. The SSI button will blink green when tractor is ready to start and remain solid green while running.

•The park brake symbol (CC) will be lit if the parking brake has not been engaged during a start attempt.

•The blade switch symbol (EE) will blink if the attachment clutch control is not in the "DISENGAGED" position during a start attempt.

•The Reverse Operation System (ROS) button (G) will be lit when Reverse Operation System is in use.

•The Headlight button (H) will remain lit while headlights are in use.

•During normal operation, the Battery Indicator Button (I) will not be lit.

FAULTS

•The SSI Button (F) will blink red for two seconds if the wrong passcode has been entered.

•The Reverse Operation System (ROS) button (G) will blink when there is a fault with the Reverse Opera- tion System. See "Reverse Operation System" in the Operation section of this manual.

•After the first unsuccessful start attempt, the Battery Indicator Button (I) will blink for two (2) seconds and then stay lit. This indicates that the battery voltage is below normal operating level. While engine is in op- eration, this light may also indicate a charging system failure.

•The Headlight Button (H) will blink when one or both of the headlight bulbs fail.

•All indicator lights will blink in the event the engine shuts off for unknown reasons; for example, if the engine has run out of fuel.

F

EE

CC

 

 

G

I

H

 

Fig. 49

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 50)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

07002

Fig. 50

TRANSMISSION

REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See“PURGETRANSMISSION” in the Operation section of this manual.

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents English/Spanish Operator’s Manual Manual de OperarioII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Toremovetractorfromcarton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigStopping See Fig To USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo USE Throttle Control D See To Move Forward and Backward See FigReverse Operation System ROS See Fig To Adjust Gauge Wheels See FigTo Operate Mower To Stop Mower BladesBattery INDICATOR/CHARGING Plug See Fig Battery Indicator Button See FigTo Transport See Fig ADD Gasoline Resetting Ignition System Passcode See FigBefore Starting the Engine Check Engine OIL LevelStarting Smartswitch Warning Lights See FigTo Start Engine PRE-STARTMowing Tips Purge TransmissionHour Meter Schedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Cleaning Deck Washout Port See Fig O P Service and AdjustmentsTo Install Mower See To Remove Mower See FigSecure with small washer and small retainer spring as shown Mower, or, counterclockwise Loosen to lower Front mower To Level MowerPulleys To Replace Mower Blade Drive BeltTo Check Brake Front Wheel TOE-IN/CAMBERBelt Removal Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel See FigInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace LED HeadlightTo Adjust Throttle Control Cable Smartswitch Ignition System Lights See FigTo Remove Hood and Grill Assembly See Fig REMOVAL/REPLACEMENTEngine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingEngine continues To run when operBattery will not Fires when turnConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationII. Funcionamiento EN Pendientes Reglas DE SeguridadAdvertencia Funcionamiento GeneralManipulación Segura DE LA Gasolina III. NiñosIV. Remolque ServicioTabla DE Materias Especificaciones DEL ProductoResponsabilidades DEL Cliente Para Remover EL Tractor DE LA Caja DE Cartón Piezas SIN MontarMontaje Herramientas Necesarias Para EL MontajeRevisión DEL Sistema DE Frenos Revisión DE LA Presión DE LAS LlantasRevisión DE LA Nivelación DEL Conjunto Revisión DE LA Posición Adecuada DE Todas LAS CorreasOperación Amperímetro Indica la carga + o la descarga de la batería Familiaricese CON SU TractorComo Usar SU Tractor Para Ajustar EL Freno DE Estacionamiento Vea FigParada Vea Fig Cómo Usar EL Control DEL Cierre Diferencial Sistema DE Operación EN Reversa ROS Vea Fig Para Ajustar LAS Ruedas Calibradoras Vea FigPara Operar LA Segadora Para Parar LAS Cuchillas DE LA SegadoraTestigo DE BATERÍA/CONECTOR DE Carga Vea Fig Para Transportar Vea FigRemolquedecarretillasootrosaccesorios Faros DelanterosPara Operar DE LA Valvula DE Gasolina DE Reserva Vea Fig Antesde Hacerarrancar EL MotorRevise EL Nivel DE Aceite DEL Motor Agregue GasolinaArranque DEL Motor Consejos Para Segar Purgar LA TransmisiónContador Horario Antes DE Cada USO MantenimientoRecomendaciones Generales Tabla DE LubricaciónLlantas TractorOperación DEL Freno Cuidado DE LA CuchillaMotor Limpieza Puerto DE Lavado DE LA Cubierta Vea Fig Servicio Y Ajustes Instale LA Segadora VeaBarra Antibalanceo S Instale la correa pasándola por encima de la polea del motor Para Nivelar LA Segadora Impresión / Inclinación DE LAS Ruedas DEL- Anteras Controlar Y Ajustar EL FrenoPara Remover LAS Ruedas Vea Fig Para Cambiar LA Correa DE Impulsión DE Movimiento Vea FigDesmontaje DE LA Correa Montaje DE LA CorreaEntrecierre Y Relé Para Hacer Arrancar EL Motor CON UNA BAT- Ería Baja Vea FigReemplazar LA Bateria Vea Fig Sustitución DEL Faro LEDREMOCIÓN/REEMPLAZO DE LA Transmisión Luces DEL Sistema DE Arranque Smartswitch Vea FigTransmisión Para Remover EL Conjunto DEL Capota Y DEL Enrejado Vea FigAceite DEL Motor AlmacenamientoOtros Sistema DE CombustibleProblema Causa Corrección Identificación DE ProblemasFuncionando cuando Pendiente Productos de consumo equipados con ruedas Garantía limitada Cómo Obtener Servicio Transmisión** Giro cero EZ y MZ Moldeada, no reforzada Service NOTES/ Aviso Service NOTES/ Aviso 11/15/13 AP
Top Page Image Contents